SUPPORT PRINTYTRON
New Model
Loading 3D preview…

Long Ash-Catching Incense Holder

Made by a Guest

Created 4 days ago

Home & Fixturesincenseash-catcherincense-holdertroughtrayno-supportshome-decor
Remix this model →

Description

A 250 × 30 mm incense holder with a shallow trough running its full length, so ash from a burning stick lands in the channel and stays off the shelf. A raised block at one end carries a 3 mm stick hole angled 35° out over the trough. The channel continues underneath the block, so ash drops straight into it.

Remix hooks

  • Stick hole diameter (3 mm): The default is snug for thin sticks. Open it to 3.3–3.6 mm for thicker ones, or to about 2.5 mm for fine sticks.
  • Hole angle (35°): A steeper angle makes the stick stand more upright and shortens the ash path. A shallower one lengthens the burn path and needs a longer tray.
  • Trough depth (5 mm) and floor (2 mm): Deepen the trough for loose ash or to hold a layer of sand. The side walls are 2 mm, so widening the trough thins them.
  • Overall length (250 mm): This is a free choice. Shorten it for shorter sticks. The block is 30 mm long and 22 mm tall.
  • Block height (22 mm): Raise it to let longer sticks clear the tray end.

Pairs with

  • A thin layer of sand or ash in the trough to catch embers.
  • Multiple holes along the block for several sticks.
  • A lid or cover cut from a flat strip for storage.

Print flat with the base down. The angled hole is drilled through the block, so check how your slicer handles the overhang at the angle and consider supports if it sags.

Photos

Technical views

SUPPORT PRINTYTRON
Tip Jar
Printytron built this for free. If it saved you a trip to the shop, a tip helps keep it free.
Need filament at a great price?
Printing this one? Stock up through our eSun partner link — your price stays the same, but Printytron gets a small commission to go towards our costs.
Draining Sleeve Foot for a Laundry Hamper Leg

Draining Sleeve Foot for a Laundry Hamper Leg

The wood at the bottom of a hamper leg is the first thing to go: it stands in whatever puddle the bathroom floor collects, drinks it up, and goes soft until the basket slumps and rocks. This sleeve slides onto the end of one rectangular wooden leg, holds the wood about 9 mm clear of the floor, and slopes its pocket floor so splash water runs out the sides instead of sitting in there against the wood. What it does Pocket: 31 × 15 mm inside, sized exactly to the leg with no added play — that measurement already accounts for clearance. 15 mm deep at its shallowest point, the centre ridge, and deeper toward the sides where the floor falls away. Stand-off: a single arched cut runs the full depth of the underside, leaving two flat feet that hold the leg about 9 mm off the floor. Overall height is about 27 mm. Drainage: the pocket floor is a shallow ridge sloping down to both long sides, with one 16 mm slot through each long wall at the low edge. Water leaves sideways, and the slot bottoms sit 10.5 mm above the floor, so no opening rests in the wet. Each slot is pointed at the top rather than flat-roofed, which is what lets it print clean. Shape: 1.2 mm chamfer at the opening to get it started over the wood, 3 mm rounding on the vertical and top edges so it doesn't snag a mop or a bare toe. The bottom edges are left sharp so they sit flat on the bed. Printing it Print in PETG with the sleeve opening facing up and the two feet on the bed — no supports anywhere. The arch sides are 45°, so the only bridge is the flat strip about 6 mm across the roof of the arch. The finished part measures roughly 36 × 20 × 27.2 mm, walls 2.5 mm thick. A plain matte finish in white, grey or black sits well in a bathroom. A zero-clearance pocket is tight in PETG. Check the leg with calipers before printing if the wood looks swollen or tapered — if it won't slide on, the pocket wants a few tenths opening up.

JollyNewt · 6 days agoRemix →