Made by devilmaycry
Created 3 days ago
Description
A table lamp stand with a twisted six-lobe column rising from a round base to a cup that holds a standard E27 lamp socket. A 12 mm bore runs down the centre and a 7 mm channel carries the cable out the back of the base, so the wiring stays hidden.
socket_d before printing; many holders vary by a millimetre or two.Print upright without supports. Use mains-rated, certified electrical parts, and a low-heat LED bulb rather than incandescent.
Photos
Technical views
Replacement two-way joiner for the top-front-center of a fiberglass-rod printer enclosure. It splices two nominal 8.2 mm rods end-to-end and carries a flat-lying arm with a screw boss for a Sercomm RC8110 camera. Print it as one piece with the arm flat on the bed, then rotate the part about the rod axis during installation to aim the camera downward and toward the bed center. Specifications Rod sockets: 8.35 mm ID, 30 mm deep per side, 0.5 mm entry chamfers, separated by a 3 mm solid center stop; 63 mm overall sleeve length. Sleeve: approximately 14.35 mm OD with 3.0 mm wall thickness. Arm: 20 mm wide and 6 mm thick, extending 50 mm from the sleeve, with a root block and gusset blending it into the sleeve. Camera boss: 28 mm diameter and 6 mm thick, with a 6.6 mm through-hole and a 12 mm × 2 mm counterbore for a 1/4"-20 camera screw. Print footprint: 63 × 71.2 × 14.4 mm as oriented on the plate; the teardrop socket bores and flat arm are intended to print without support. Fit: press-fit for measured 8.19–8.20 mm rods; PETG wall thickness is sized to resist splitting and bending from the tensioned enclosure fabric.
A 25 mm square corner block, 8 mm tall, with a quarter-circle channel on top that seats a 10 mm LED strip and turns it 90 degrees. Made for under-shelf lighting where the strip needs to follow an inside corner without kinking. The underside is flat, so it takes adhesive tape or double-sided foam. The channel is 10 mm wide and 4 mm deep, with a 12.5 mm centerline radius. It enters and exits through the two sides that meet at the far corner. Vertical corners carry a 1 mm chamfer. Remix hooks Block size (25 mm): the main lever. A 35 mm block with a 17.5 mm centerline radius gives a gentler bend for stiffer strips. Centerline radius (12.5 mm): keep it at half the block size so the channel meets the edges, or shrink it for a tighter turn. Channel width (10 mm): add 0.3 to 0.5 mm of clearance for strips with thick silicone sleeves, or narrow it for bare strips. Channel depth (4 mm): deepen it to sink the strip below the surface, or make it shallower and add a diffuser lip. Height (8 mm): can be lowered to about 6 mm and still keep the 4 mm channel with a solid floor. Pairs with Straight strip sections between corners, with one bracket per inside corner. A snap-in diffuser cover cut to the same 10 mm channel width. A mirrored variant for the opposite corner direction. Print notes Print flat on the back, with no supports needed. Use PETG or ABS if the bracket sits near warm drivers.

A raised feeding platform in the spirit of a low mesa: a broad, tapered block with two round recesses cut into the top, built to lift a pair of 160 mm pet bowls to 120 mm so an older dog with dodgy hips can eat without stooping. The bowls drop into their rings and stay put, so a shove across the kitchen floor doesn't send them travelling. Wide cross feet at each end extend the footprint to 270 mm front to back, giving the stand a planted, anti-tip stance. Design notes Height: 120 mm overall Recesses: two, 164 mm diameter (160 mm bowl plus 4 mm clearance), 25 mm deep, with a chamfered lip for easy drop-in Spacing: 40 mm between the two recesses Footprint: 460 mm long, tapering upward, with a hollow underside to save material Anti-tip feet: 10 mm thick cross feet, 270 mm deep, at both ends Print notes At 460 mm long, the stand is larger than most print beds. Plan on a large-format printer or split it into sections. Bowls with a different diameter need the recess size adjusted to match.
This T pipe inlet joins a 31 mm line to a 41 mm line instead of stacking adapters that leak at every joint. The main run holds its 41 mm outside diameter all the way past the side branch, then necks down through a short taper to a 31 mm spigot long enough to grip a hose or slide into a coupling. The plate carries two identical copies side by side, 70 mm apart along Y, so one print gives you a pair; each copy is a separate hollow part with nothing to assemble. Fit and print notes Two identical pipes laid out side by side, 70 mm apart across Y Main run: 84 mm long overall per pipe — the 41 mm OD section carries on past the branch to within a few millimetres of its edge before reducing 41 mm centre section: 48 mm long Taper: 6 mm, from 41 mm OD down to 31 mm OD Reduced end: 30 mm of straight 31 mm OD spigot Other end: stays at the full 41 mm OD, no reduction Side branch: 31 mm OD, 45 mm out from the centreline Bores: 26 mm through the 31 mm spigot and the branch, 36 mm through the 41 mm section Wall thickness: 2.5 mm throughout Sits flat on the plate, no supports needed Only one end reduces, so orientation matters when you install it. The 84 mm length is what keeps the branch on the full-size section — check the gap before you commit, and dry-fit the 41 mm end first if it has to butt against something.

A 250 × 30 mm incense holder with a shallow trough running its full length, so ash from a burning stick lands in the channel and stays off the shelf. A raised block at one end carries a 3 mm stick hole angled 35° out over the trough. The channel continues underneath the block, so ash drops straight into it. Remix hooks Stick hole diameter (3 mm): The default is snug for thin sticks. Open it to 3.3–3.6 mm for thicker ones, or to about 2.5 mm for fine sticks. Hole angle (35°): A steeper angle makes the stick stand more upright and shortens the ash path. A shallower one lengthens the burn path and needs a longer tray. Trough depth (5 mm) and floor (2 mm): Deepen the trough for loose ash or to hold a layer of sand. The side walls are 2 mm, so widening the trough thins them. Overall length (250 mm): This is a free choice. Shorten it for shorter sticks. The block is 30 mm long and 22 mm tall. Block height (22 mm): Raise it to let longer sticks clear the tray end. Pairs with A thin layer of sand or ash in the trough to catch embers. Multiple holes along the block for several sticks. A lid or cover cut from a flat strip for storage. Print flat with the base down. The angled hole is drilled through the block, so check how your slicer handles the overhang at the angle and consider supports if it sags.

GripRoot is a replacement cane tip for a 19 mm tube, built for the case where an old tip has worn through and started to clack. A wide 40 mm base spreads the load, a tapered body leads up to a deep socket, and a cross-hatch tread on the underside gives grip on wet floors. The grooves run straight out through the edge of the base, so water has a path to escape instead of pooling under the tip. Dimensions Base diameter: 40 mm, with a chamfered lower edge Overall height: 31 mm Neck diameter at the top: 29 mm Socket: 19.5 mm inner diameter, 25 mm deep Socket mouth: small flared lead-in to help the tube seat Tread Cross-hatch grid of grooves, 3 mm wide and 2.5 mm deep 6 mm pitch in both directions Grooves open at the base edge for drainage Print notes Designed for stiff TPU, printed base-down with no supports needed The 19.5 mm socket against a 19 mm tube gives roughly 0.5 mm of interference, which suits a flexible material Measure the actual tube before printing, since nominal 19 mm tubing often varies slightly Adjust socket diameter or groove depth if a tighter grip or a more aggressive tread is wanted