Lever — EDC Money Clip
Created 1 months ago
Description
Launch a heavy-duty daily carry designed to tackle two essentials at once. Engineered specifically for a birthday gift, this rigid money clip secures folded banknotes while integrating a discrete bottle opener into the reinforced base plate. The top face features bold, industrial Bebas Neue typography to celebrate the recipient.
Features
- Reinforced Base: Thickened lower plate featuring a targeted cutout to grip and pop standard 26mm bottle caps.
- Tension Fit: A precise 1mm tuned gap securely holds an everyday stack of approximately 8 folded banknotes.
- Typography: Bold "DAD" lettering extruded on the upper face.
Dimensions
- Profile: 60mm overall length by 30mm width.
- Format: Scaled specifically to house standard bottle caps without compromising the clip's structural integrity.
Images
More like this
Explore more in Keychains & EDC →
Chunky Modern Type Keychain
A solid, pocket-sized keychain featuring a custom typographic design. The base perfectly contours the bold lettering, creating a clean and modern silhouette that feels sturdy in hand. Pocket-Friendly Size: Scaled down to slide easily into a pocket without snagging. Sturdy Build: A solid 5 mm base prevents flexing, with 2 mm raised lettering that holds up to daily wear. Ready to Mount: Features a fully through 5 mm keyring hole to accommodate standard rings or small carabiners.
Captive-Pea Emergency Keychain Whistle
A 50mm print-in-place emergency whistle built around a 12mm spherical resonating chamber. It features a tapered mouthpiece and an integrated 7mm captive pea that creates a high-decibel warble, all packed into a low-profile keychain block. Remix Hooks & Constraints Chamber Geometry: The fundamental tone is dictated by the 12mm sphere. Expanding this chamber lowers the pitch, while shrinking it creates a sharper, higher shriek. Captive Pea: The 7mm pea prints with a 0.2mm floor gap. This clearance is just tight enough to prevent the sphere from tearing off the build plate, but weak enough to break free with a pen tip. Windway & Fipple: The air channel is fixed at 1.5mm high to compress the airstream before it hits the 45-degree splitting edge. Changing the fipple angle will dramatically alter the sound quality. Mounting Loop: The 5mm bore at the rear fits standard split rings and 550 paracord. If scaling the model for a heavier carabiner, reinforce the tail block first.
Dog Remote Belt Holster 3
Fumbling for the remote when you actually need it defeats the point of having one. This holster locks the transmitter to your belt so it stays exactly where your hand expects it to be. The front channel leaves the main buttons clear to press without drawing the remote, and the bottom cutout lets you push it up easily when you do need it. Fit Details Sleeve Dimensions: Fits bodies up to 34 mm wide and 28 mm thick. Clip Capacity: Fits belts up to 45 mm (1.75 inches) wide and 6 mm thick. Printing: Print standing upright. PETG is strongly recommended over PLA so the belt clip has enough flex to snap over your belt without snapping off.
Embossed Corporate Logo Keychain
A minimalist, single-piece keychain blank featuring raised corporate typography. The body uses a flat-bottomed pill geometry to print seamlessly on an FDM bed without supports, while the integrated mounting hole ensures the outer perimeter remains completely uninterrupted. Print Specifications: Dimensions: 65 mm × 32 mm × 4.2 mm (total height including text). Mounting interface: 5.5 mm diameter integrated hole, positioned for 4 mm of solid wall thickness to resist torsion. Lettering clearance: Text is extruded 1.2 mm above the base layer, providing enough depth for a mid-print filament swap if high-contrast text is desired. Material guidance: Prints cleanly in PETG or PLA. No brim required.
Flush Face Bean Fidget
What it's for A pocket-sized fidget shaped like a standing bean, designed to house a standard Cherry MX mechanical keyboard switch. The face plate acts as an oversized keycap, sitting flush within the body's front pocket when at rest, and depressing smoothly inward when clicked. Dimensions Overall Assembled Size: ~36 x 24 x 50 mm Switch Fit: Standard 14.1 mm friction-fit MX socket with bottom clearance for the center pin. Face Cap Tolerance: 1 mm gap around the perimeter of the face plate to ensure frictionless travel inside the pocket. Assembly Snap an MX switch into the back of the body cavity. Press the face plate's rear stem bracket firmly onto the switch's cross stem. No glue required if tolerances are dialled in on your printer.
Horizontal Fidget Tower
hi