Massives ESP32 Sensor-Gehäuse
Created 1 months ago
Description
What it's for
Ein massives, komplett schraubenloses Gehäuse-System für ESP32-Projekte. Alle Komponenten werden in maßgefertigte Schienen eingeschoben. Der ESP32 rastet im Unterteil ein, das OLED-Display und der Lichtsensor finden im Deckel Platz.
Dimensions
- Außenmaße: 200 × 140 × 70 mm
- Wandstärke: 3 mm
- ESP32-Schienen: Passend für 55,3 × 28,0 mm (DevKitC)
- OLED-Schienen: Passend für 27,3 × 27,3 mm (bis 11 mm Tiefe)
- VEML7700-Schienen: Passend für 17,7 mm Breite
Assembly
Beide Teile (Basis und Deckel) werden separat auf dem Druckbett platziert. Der Deckel wird auf dem Kopf liegend gedruckt, um Support für die Deckeloberfläche zu vermeiden. Die Komponenten werden einfach in die Schienen auf der Innenseite eingeschoben, danach wird der Deckel durch die Passkante auf die Basis gedrückt.
Images
More like this
Explore more in Storage & Organization →
C Clip for 9V Battery Container
What it's for A snap-in C clip that holds a 22 x 33 mm 9 V battery container. The opening sits in the front long wall, so the container presses in and pulls out when the battery needs changing. Dimensions Inside pocket: 22 x 33 mm Height: 20 mm Wall thickness: 2.5 mm Opening: 27 mm wide, leaving 3 mm of retaining wall on each side Outside: 38 x 27 mm Remix ideas Widen the opening to 28 or 29 mm for an easier release. Add a mounting tab or screw holes on the back wall. Print in PETG or nylon for better flex at the snap.
Caregiver Check Station Enclosure, Gray and Red
A caregiver check-in box with no obvious place to tap, and a back panel that fights you at every repair. This enclosure puts a large red TAP HERE panel on the front and a screw-on back cover behind it, so the electronics come out without disturbing the front. Size: 150 × 110 × 36 mm body, with a 3 mm back cover. NFC panel: 64 × 64 × 2 mm red panel, replaceable, behind a 1.5 mm lip. It is held by a separate holder with four M2.5 screws. Back cover: four M3 × 12 screws into body posts, with a 0.3 mm clearance skirt. Two keyhole slots handle wall mounting. Openings: PIR window 23 mm, three 5 mm LED holes (green, yellow, red), BME280 air slots, 12 × 6.5 mm USB-C slot, 5 mm reed-switch cable hole, and top and bottom vent slots. Printing: body and panel face-down, cover outside-down. PLA, no supports, 3 walls, about 15% infill. Not final: every board position is a placeholder. Measure the ESP32, PN532, PIR and BME280 before fixing the internal layout.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Support 25 Clés USB
Un support de bureau lourd et stable conçu pour ranger et organiser 25 clés USB en un seul endroit. Variables à ajuster Espacement (28 mm x 23 mm) : Pensé pour accepter la plupart des corps de clés USB sans qu'elles se chevauchent. Peut être resserré si vous n'avez que des clés très fines. Taille des encoches (14 mm x 7,5 mm) : Les fentes offrent un jeu confortable autour d'un connecteur USB-A standard. Profondeur (12 mm) : Laisse les clés bien droites tout en conservant 3 mm de matière pleine au fond du bloc (hauteur totale de 15 mm).
lock 95x155
An open-top rectangular tray with a 95 x 155 mm outer footprint, 50 mm total height, and 2 mm floor and walls. It leaves a 91 x 151 x 48 mm interior. Fit notes Outer size: 95 mm (X) x 155 mm (Y) x 50 mm (Z). Inner cavity: 91 x 151 mm, 48 mm deep. Measure the item you plan to store against the 91 x 151 mm interior before printing. Not included: lid, dividers, corner rounding, mounting holes. Corners are square.