Maverick Dash Phone Wedge
Created today
Description
A low-profile dash wedge built to tuck securely behind the gauge cluster in a Ford Maverick. It sits low to stay out of the primary sightline, angling the phone back steeply for easy screen viewing while keeping it firmly trapped behind the 6mm front lip.
Dimensions to tweak
- Slot width: The flat pocket is currently 14mm wide, which clears most phones in a standard case.
- Rear slope: The back face is pitched forward slightly (the top edge sits 12mm inward from the base) to clear the sloped cluster plastic.
- Overall height: Capped at 30mm max.
Images
More like this
Explore more in Automotive, RC & Hobby →
Tapered Traxxas Slash Front Bumper
A replacement front bumper designed for the Traxxas Slash chassis, featuring a tapered wedge geometry on the leading edge. The angled profile directs frontal impact energy upward, allowing the vehicle to ride over ground obstacles rather than absorbing direct perpendicular strikes from curbs or barriers. Target Specifications Vehicle Fitment: Traxxas Slash chassis Mounting Interface: 25mm horizontal pitch Hardware Required: Designed for two M3 fasteners Mount Location: Recessed 8mm from the rear bumper face Primary Feature: Angled lower deflection wedge
M2 Slotted GO 3S Mount
Fixed-angle TPU sleeve for the standalone Insta360 GO 3S camera, geared for flat-top drone frames like the AOS series. The Fit: Holds the bare GO 3 / GO 3S camera unit only (not the Action Pod). The Mount: Slotted M2 tracks spanning 19mm to 27mm, meant to catch 20x20 or 25.5x25.5 top plate hardware. The Pitch: Locked at 25 degrees of up-tilt. Print in TPU. Do not try this in rigid plastics; you'll never get the camera seated.
Print-in-Place Flexible Crocodile
Toy reptiles are fine until you try to pose them and realise they're cast into a single, rigid block that snaps if you push it. This fixes that. It’s an eight-segment articulated crocodile that prints entirely assembled, right on the bed. The joints are enclosed captive hinges with a 0.45mm clearance, meaning they fuse just enough structure to print safely before breaking free instantly for a massive range of motion. The body tapers from a stylized head down to a narrowed tail, with distinct rib extensions and legs built into the mid-sections. Print Instructions Clearance: 0.45mm gaps in the hinges — make sure your flow rate is dialed in to avoid the joints fusing. Layer Height: 0.2mm recommended. The internal pin tapers rely on standard layer heights to bridge successfully. Adhesion: It prints flat. No brim is required unless you have severe warping issues on small footprints (like the tail tip). Supports: None. The hinge pins use 45-degree chamfers so they print perfectly in mid-air inside their sockets.
Dwarven Rampart With Battle Scatter
A heavy tabletop defense rampart for 28mm-scale wargaming, featuring a wide walkway, solid rear stairs, and deep dwarven geometric cuts along the front. Remix Hooks Scale: The wall sits at a 120mm width and 30mm height — scale the overall block if you're fielding larger forces. Scatter: The walkway holds a small 12x10mm dropped chest and a plunged sword. You can freely translate these across the -Y and X axes, or replace them with your own fallen shields and banners. Details: The geometric diamond cuts on the front face are modular — swap the depth or pattern to match your specific underground factions.
Door Handle Insert Storage Tray
A hollow storage tray insert designed to slip into the factory grab handle cavity of a vehicle door panel. The primary body tapers downward with a slight asymmetric offset to clear internal door mechanisms, while a perimeter lip catches the edge of the armrest opening to suspend the tray in place. Top Profile: 135mm x 42mm (excluding lip) Depth: 58mm clearance Wall Thickness: 2mm standardized shell Fitment Note: Based on approximate baseline dimensions for mid-size SUV door handles. The retention lip extends 4mm outward to prevent the tray from falling into the door cavity.
5/16x14 Cue Joint Protectors
A matched set of joint protectors for pool cues using the 5/16x14 piloted joint standard, heavily used by Schon and similar makers. Includes a female cap to protect the exposed butt pin, and a male plug to seal the shaft insert. Both feature fluted outside edges for easy threading and unthreading. Remix Hooks Cue Diameter: Default is 21.5mm OD. Thicker cues might want 22mm; older cues might sit closer to 21.2mm. Clearance: The female thread (butt protector) is oversized by 0.6mm, and the male pin undersized by 0.2mm to survive FDM printing tolerances. Dial these in depending on your printer's flow rate. Pilot Recess: The butt protector has a 13.5mm diameter x 3.5mm deep recess to clear a standard Schon pilot collar. Grip Profile: The 4mm semi-circle edge flutes can easily be swapped for a knurled mask or flat-cut hex sides.