Onewheel Charger Port Plug
Created today
Description
Mud, sand, and metallic dust have a habit of finding their way straight into the exposed charge port, packing it solid until the charger refuses to seat properly. This plug seals the port to stop the debris before it becomes a problem.
Fit and Printing
- Insert Diameter: 15.3mm, designed to friction-fit a standard Onewheel XLR charge port.
- Alignment: Features a 2.5mm keyway rib to match the port's orientation slot.
- Removal: Includes an extended tab with a 3.5mm hole for a lanyard, making it easy to yank out even with gloves on.
- Material: Print this in TPU (flexible filament) for a watertight seal and best friction fit, though PETG will work if your printer's tolerances are dialed in.
Photos
Technical views
More like this
Explore more in Automotive, RC & Hobby →
M2 Slotted GO 3S Mount
Fixed-angle TPU sleeve for the standalone Insta360 GO 3S camera, geared for flat-top drone frames like the AOS series. The Fit: Holds the bare GO 3 / GO 3S camera unit only (not the Action Pod). The Mount: Slotted M2 tracks spanning 19mm to 27mm, meant to catch 20x20 or 25.5x25.5 top plate hardware. The Pitch: Locked at 25 degrees of up-tilt. Print in TPU. Do not try this in rigid plastics; you'll never get the camera seated.
Onewheel Trunk Cradle
A thirty-pound wheel rolling freely in the back of a moving car is a problem that solves itself by smashing your groceries. This cradle stops the board from tipping and sliding on every sharp turn. Footprint: 180mm wide by 160mm deep — fits cleanly on most printer beds. Fit: The 290mm curve holds XR and GT tires perfectly, and Pints will seat securely against the slopes. Anchors: Features four 5.5mm countersunk holes for bolting directly to a cargo floor or wood base, plus two side channels for hooking a standard bungee cord over the tire. Printing: Needs a decent amount of infill (15-20% minimum) to handle the board's weight. No supports required.
Walkable SPD-SL Cleat Cover
What it's for A slip-on protection cover designed for Shimano SPD-SL road cycling cleats. It prevents slipping on hard surfaces like wet cafe tiles while protecting the plastic cleats from premature wear off the bike. Features a deep, cross-hatched tread pattern on the sole for traction. An internal tapered lip locks the cover securely over the top edge of the cleat hardware. A solid rim surrounds the treads to prevent the edges from catching while walking. Dimensions Internal Layout: 75mm long by 55mm wide at the heel, matched to standard SPD-SL profiles. Side Walls: 3mm thick for lateral rigidity and protection. Base: 4mm thick solid sole, structured to accommodate 2.5mm deep tread grooves. Materials Printing this model in a flexible filament like TPU is strongly recommended. The flexibility allows the inner retaining lip to stretch over the cleat body during installation and removal, while the rubber-like material provides the necessary slip resistance. Remix ideas Adapt the internal cavity geometry and overall footprint to fit Look Keo or standard SPD cleat profiles. Replace the cross-hatched tread with aggressive horizontal lugs or a custom dot pattern. Add a small tether loop to the heel end to leash the covers together when stored in a cycling jersey pocket.
Print-in-Place Flexible Crocodile
Toy reptiles are fine until you try to pose them and realise they're cast into a single, rigid block that snaps if you push it. This fixes that. It’s an eight-segment articulated crocodile that prints entirely assembled, right on the bed. The joints are enclosed captive hinges with a 0.45mm clearance, meaning they fuse just enough structure to print safely before breaking free instantly for a massive range of motion. The body tapers from a stylized head down to a narrowed tail, with distinct rib extensions and legs built into the mid-sections. Print Instructions Clearance: 0.45mm gaps in the hinges — make sure your flow rate is dialed in to avoid the joints fusing. Layer Height: 0.2mm recommended. The internal pin tapers rely on standard layer heights to bridge successfully. Adhesion: It prints flat. No brim is required unless you have severe warping issues on small footprints (like the tail tip). Supports: None. The hinge pins use 45-degree chamfers so they print perfectly in mid-air inside their sockets.
Dwarven Rampart With Battle Scatter
A heavy tabletop defense rampart for 28mm-scale wargaming, featuring a wide walkway, solid rear stairs, and deep dwarven geometric cuts along the front. Remix Hooks Scale: The wall sits at a 120mm width and 30mm height — scale the overall block if you're fielding larger forces. Scatter: The walkway holds a small 12x10mm dropped chest and a plunged sword. You can freely translate these across the -Y and X axes, or replace them with your own fallen shields and banners. Details: The geometric diamond cuts on the front face are modular — swap the depth or pattern to match your specific underground factions.
Door Handle Insert Storage Tray
A hollow storage tray insert designed to slip into the factory grab handle cavity of a vehicle door panel. The primary body tapers downward with a slight asymmetric offset to clear internal door mechanisms, while a perimeter lip catches the edge of the armrest opening to suspend the tray in place. Top Profile: 135mm x 42mm (excluding lip) Depth: 58mm clearance Wall Thickness: 2mm standardized shell Fitment Note: Based on approximate baseline dimensions for mid-size SUV door handles. The retention lip extends 4mm outward to prevent the tray from falling into the door cavity.