Overwatch — Event Badge Holder
Created 2 days ago
Description
A rigid, oversized vertical credential holder built to exactly 5.5 × 3.5 inches footprint. It features a central thumb cutout to let you quickly pop the badge out when needed, while retaining tabs lock the card securely in place during wear.
Features
- Dual Attachment Points: Lanyard and clip slots at both the top and bottom edges so you can hang it standard or tether it down.
- Snap-In Tabs: Low-profile overhanging clips securely grip the top and bottom of the card.
- Thumb Ejector: A large central window in the backplate makes removing the badge quick and frictionless.
Images
More like this
Explore more in Keychains & EDC →
Football Keycap Topper
A custom Cherry MX-compatible mechanical keycap featuring a gently domed top and recessed seams, channeling the look of a classic basketball. Built from the ground up to respect a precise 17.25mm footprint, it trades the standard typing dish for a smooth, tactile convex surface. Court-Ready Specs Switch Profile: Deep Cherry MX compatible stem with a flared entrance for an easy press-fit. Surface Feel: A smooth domed top intersected by 0.6mm-deep recessed channels tracing the iconic hoops cross-and-arc pattern. Dimensions: Exact 17.246 mm square footprint at the base, tapering cleanly up to the rim. Printability: Designed fully manifold with built-in internal bracing ribs. The bottom cross interface is lightly chamfered to combat elephant's foot and ensure tight tolerances straight off the bed.
BTS Balm Capsule
A bright pink travel capsule sized for standard lip balm tubes, featuring the BTS door logo repeating across the exterior. The friction-fit cap includes a sturdy heart-shaped loop for attaching to a keychain or lanyard, keeping your balm secure and accessible on the go. Staggered logo pattern wrapping both the sleeve and cap Built-in push hole at the bottom to easily eject the tube Sized with a 16mm inner diameter to prevent rattling
M22 Threaded Kettlebell Stash
A two-piece threaded kettlebell stash keychain. The main body has been hollowed out to maximize internal storage, then split squarely at the equator with a sturdy 2mm-pitch thread holding the halves together. Both halves print exactly as oriented — the base sits flat on its machined underside, and the top half prints directly on its equator ring. Fitment Notes Thread Clearance: Engineered with a 0.5mm radial offset on the internal thread. Check your flow rate if the halves bind on the first turn. Split Ring: The arch remains standardized for a 1.5mm wire gauge ring. Internal Volume: The cavity is approximately 20mm wide and 19mm deep when closed. Fits standard folded emergency bills or small hardware.
CourtGuard — Vented Finger Splints
Designed to quickly immobilise jammed or sprained fingers, CourtGuard splints provide rigid support without trapping moisture. Ideal for handling the inevitable basketball court impacts, the half-cylinder trough design features a rounded capsule geometry that sits comfortably against the skin without digging in. A dorsal ridge of vent holes keeps the finger cool during recovery, while integrated side notches securely anchor standard Velcro straps to keep the splint exactly where it belongs. Sizes Included Small (Pinky): 55mm length, 15mm inner diameter, 4 vent holes. Medium: 65mm length, 18mm inner diameter, 5 vent holes. Large: 75mm length, 21mm inner diameter, 6 vent holes. Print Notes All three sizes are designed to print-in-place in their current flat orientation, requiring absolutely no supports. A rigid material like PETG or standard PLA is recommended for maximum immobilization.
90x60mm Campaign Magnet-final-final-super-final
A three-colour stepped campaign magnet formatted for a 90x60mm footprint. Designed to print cleanly with two manual filament swaps. Fitment Magnets: Four 6.05mm x 3mm disc magnets, set into the rear face. Layer Heights: Blue base to 3.6mm, white layer to 4.6mm, red top layer to 5.6mm. Features a classic bell-tower schoolhouse and a reshaped apple graphic flanking the bottom text line, with adjusted margins across the middle lines to tighten up the vertical spacing.
Round Tuit Dual-Sided Token, V 1
A 50 mm dual-sided token featuring bold raised text on the front and flush, mirrored text inlaid on the back. Designed to be printed flat on the bed, using contrasting colours to make the details pop. Front: Raised "Round TUIT" text Back: Flush-inlaid "3DP@GIRTON.ORG" text Dimensions: 50 mm diameter, 3 mm base thickness