Perch — Clamp-On Headphone Holder
Created today
Description
Perch is a three-piece desk-edge headphone holder: a main body with hook and clamp jaws, a separate threaded adjustment screw with a large scalloped knob, and a loose pressure pad. Nothing is joined or printed in place, so the parts are laid out separately and assembled by hand after printing.
Features
- Clamp range of 15–35 mm, suited to a 20 mm desk
- Internal thread in the lower jaw with 0.4 mm radial clearance for the 18 mm, 4 mm-pitch screw
- 40 mm knob with scalloped grip
- Pad snaps onto an 8 mm peg at the screw tip and spins freely
- Reinforced hook with gusset and rounded lip
Print notes
- Body on its side, screw knob-down, pad flat
- PLA, 0.4 mm nozzle, 0.20 mm layers, 4 walls
- No supports expected
Assembly
Thread the screw up through the lower jaw from below, then press the pad onto the peg. Set the source's mode value to 1, 2 or 3 to export each part individually.
Images
More like this
Explore more in Desk & Tech →
Desk Clamp Headphone Holder, 15–35 mm
What it's for A two-piece headphone holder that clamps to a desk edge and holds headphones on an upper hook arm. A threaded screw with a large knob under the lower jaw tightens it. Dimensions Desk thickness range: 15–35 mm Width: 40 mm Body height: about 69 mm Hook reach: 55 mm past the spine, with a raised lip Screw: 10 mm diameter, 3 mm pitch, 26 mm pad, 32 mm knob Print notes Two parts: clamp body and screw Print the body on its side (40 mm face down) and the screw upright, both without supports PLA, 4 or more perimeters Remix ideas Add a rubber or felt pad to the screw head Lengthen the hook arm for larger headphones Add a cable notch on the lip
Pizza Spinner Fidget Print Set
What it's for A pizza-shaped fidget spinner that turns freely on a central hub. The pepperoni and olives are separate snap-on toppings, each with a split pin that clicks into a socket. Each topping also has a marked seat in the sauce, so the right position is easy to find. Dimensions Pizza: 62 mm diameter, bumpy crust, sauce with slice grooves Hub: protrudes on both sides, 0.5 mm clearance to the pizza 6 pepperoni: 10 mm, seat 10.6 mm 9 olives: 5 mm, seat 5.6 mm Pins: 3.4 mm split pins into 3.5 mm sockets Print notes Toppings print upside down, pin facing up, no supports needed. Olives are small; a standard 0.4 mm nozzle will soften the details. Pieces print in separate colours and can be mixed freely. Remix ideas Add mushrooms or peppers using the same pin and seat. Change the topping layout by moving the seat positions. Make the hub longer for a better grip.
Samsung S24 FE Snap-In Bumper Case
A one-piece snap-in bumper case for the Samsung S24 FE, sized from the 162.0 × 77.3 × 8.0 mm phone spec with 0.2 mm clearance. The open front leaves the screen clear, and the walls are 1.8 mm with a 1.5 mm back and a 1.2 mm lip that catches the screen edge. Camera cutout on the back Button slot along one side Bottom slot for USB-C and the speaker Prints back-down with no supports One piece, no assembly The case is rigid, so the phone presses in from one corner. PLA works, but a flexible filament such as TPU is easier on the phone and less likely to crack the lip. The camera and button positions are estimates, so check them against your phone before printing the whole case.
ReplixHD Gaming Cable Holder.
A low, slate-like desk plate in the spirit of a game-console accessory, with three rounded C-shaped clips standing in a symmetrical row. Cables press in from above, sit in a 4.4 mm round channel, and are held by smooth lips. Size: 60 × 20 mm, 5 mm base, 7 mm total height. Clips: three, 17 mm apart, 3.6 mm entry opening, lips about 1.2 mm thick at the opening. Floor: about 1.8 mm of material under each channel, measured from the tape recess. Underside: 48 × 12 mm tape recess, 0.5 mm deep. Printing: one solid piece, flat bottom, no supports needed.
Card Press met Schroefdop
Een persbakje voor Pokémon-kaarten, bestaand uit vier losse printdelen: een bakje, een persplaat, een draaischroef en een schroefdop. Het bakje is dicht aan de achter- en zijkanten, heeft een vingeruitsparing aan de voorkant en een brug met schroefdraad over de bovenkant. De plaat ligt op de kaarten en heeft een ronde inzinking in het midden. De draaischroef zet de plaat onder druk. De schroefdop draait op de punt van de schroef en heeft een ronde voet die in de inzinking past. Binnenruimte bakje: 68 × 93 mm Schroefdraad: 14 mm, spoed 3 mm Inzinking in de plaat: 16 mm doorsnede Schroefdop: 15 mm voet, 22 mm doorsnede Print de dop met de voet naar beneden, zonder support
Desk Holder for 6 USB Sticks
A solid block with six angled slots that keeps USB-A sticks upright on the desk instead of loose in drawers. Each slot leans back 30 degrees, so labels on the sticks face a person seated at the desk. Each slot is sized for a standard USB-A stick with a little room to spare, and the slots are separated by 2.5 mm dividers. The outer edges have a small chamfer, and the base sits flat on the bed with no supports needed. Capacity: 6 USB-A sticks Slot size: 13 mm wide, 6 mm deep Slot angle: 30 degrees tilted back Divider thickness: 2.5 mm Overall size: about 95 mm long, 19 mm deep, 30 mm tall Print orientation: flat on its base, no supports