ploca 1/4
Created today
Description
A 200 x 200 x 10 mm board with a 5x5 engraved grid and a 4 mm through-hole in the centre of each of the 25 cells. Two 4 mm side holes, 6 mm deep, sit at the midpoint of the front and left faces.
Check before printing
- Side hole depth: 6 mm, drilled in from the face at mid-thickness (5 mm).
Fit notes
- Holes are 4 mm nominal, so no clearance is added. They suit M4 screws only with a tight fit. Ream or enlarge them if needed.
- The side holes are blind and do not meet the vertical holes.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Platte mit Schrift
What it's for Kleine Beschriftungsplatte mit erhabenem Schriftzug HENKIES und zwei Befestigungslöchern, z. B. als Namensschild oder Anhänger. Dimensions Platte: 70 × 18 × 1 mm Löcher: 2 × Ø 4 mm, 55 mm Abstand (Mitte zu Mitte), mittig auf der langen Achse Schrift: HENKIES, 0,7 mm erhaben, mittig, Gesamthöhe 1,7 mm Schriftart: Liberation Sans (Arial-kompatibel) Remix ideas Ecken abrunden Größere Schrift oder andere Schriftart Zusätzliche Fase an den Plattenkanten
Women's Sunglasses Frame with Folding Arms
Printed sunglasses where the parts crowd each other on the plate and fuse: this set lays the frame, two folding arms, ribbon inserts and hinge pins out with clear space between them. Frame width: 145 mm, 50 mm tall, 5 mm plate, hinge ears 18.5 mm high Lens openings: 50 × 36 mm each, 16 mm bridge gap Arms: about 139 mm long, 8 mm wide, 6 mm thick, with at least 4.8 mm between each part on the plate Hinge pins: four, 2 mm across, in 2.4 mm holes Hearts and breast cancer awareness ribbons recessed 1 mm on the frame and arms Print flat, no supports needed for the arms
Pallina Natalizia Vetro Soffiato Classica
Una pallina da albero dal sapore vintage, con la sua sfera lucida, il cappuccio dorato e l'anello per il filo. Tre fasce in rilievo girano attorno al corpo come i vecchi addobbi di vetro soffiato. Diametro sfera: 50 mm Anello in alto per nastro o gancio Tre fasce decorative che si possono stampare in un colore a contrasto Ottima da appendere o da regalare
4 mm Hanging Hole Snowflake Christmas Ornament
A flat, six-armed snowflake ornament with a 4 mm string hole through a round eyelet that sits on the tip of the top arm. It prints as one solid piece, 3 mm thick, flat on the bed with nothing to support. Fits String, twine or thin ribbon up to roughly 4 mm through the eyelet; a knot or bead wider than the hole keeps it from pulling through. A tree branch, hook or nail with about 71 mm of clear height, so the eyelet and the point below it hang free. Does not fit / not included No hook, clip, stand or separate hanger — the eyelet is part of the print itself. No text, logo or engraved date; nothing is lettered on it. Not a multi-part kit; there is nothing to assemble. Check before printing Overall footprint is 55.3 mm wide across the flat sides and 70.5 mm tall including the eyelet, at 3 mm thick. Confirm the hanging spot leaves that much room and that your cord end passes the 4 mm hole — a hole that prints slightly tight may need a quick ream with a 4 mm drill bit. What is on the part Six broad arms, 4.5 mm wide with rounded ends, joined by side branches 4 mm wide — thick enough to handle and pack away each year. A 14 mm hexagon at the centre with a 6 mm hole through it, which trims filament without thinning the arms. An 11 mm rounded eyelet overlapping the full width of the top arm, so it reads as an extension of the arm rather than something stuck on. Every arm and branch is solid and properly joined, so the whole ornament stays low on filament while holding up to a season of hanging.
Lantern Support Frame Stops Cardboard Sides Bowing
A cardboard Diwali lantern bows at the panels and loses square at the corners. This insert frame sits inside the lantern and holds all four walls out at full width, so the sides stay flat instead of sagging inward. Assembled, it measures 417 mm square, with a 4 mm thin outer border and two 6 mm diagonal braces crossing at the centre in an X, all 30 mm tall. Fit Assembled outer size: 417 × 417 mm (41.7 cm) Inside opening: 409 × 409 mm, set by the 4 mm border Height: 30 mm — depth is what keeps the cardboard from flexing, so go taller before wider if it still bows Two 6 mm diagonal braces meet in the middle of the opening Hidden inside the lantern once it is closed up Printing and assembly Prints as four separate corner pieces, labelled Corner Piece A–D. They are the same shape rotated, so print the same piece four times. Each piece is about 209 × 217 × 30 mm, so the bed needs roughly 217 mm square plus printer margin. Inner joints use dovetail tabs and matching sockets at the centre where the X arms meet. Slide each tab straight down into its socket; these joints lock mechanically. Outer wall joints use a plain full-thickness slot, open at the outer face and 0.3 mm wider than the tab. The neighbouring tab slides in flush with both wall faces; a 4 mm wall is too thin for a dovetail lock there, so add a drop of glue. Tabs sit inside the sockets and do not add to the outer size. Each tab extends 8 mm past its cut edge — without that it cannot lock — and it is hidden once the frame is assembled. The outer-wall tab sits at the centre of the 4 mm wall, 2 mm in from the outer edge, with its tip trimmed flush so nothing sticks out past the wall faces. The border is only 4 mm wide, so the joints are the weak point: print with extra perimeters and handle the assembled frame by the border rather than the tabs.
Festive Headstand: Upside-Down Pineapple with Ball Gag
A cartoon pineapple does a festive headstand: it balances on an oversized leafy crown, the fruit body rising above, and a big fluffy red Christmas hat droops off to one side, ending in a single large rounded bobble. Two wide-open eyes with dark pupils and brows sit on the fruit, a small skin-toned nose between them, and a black ball gag framed by small red puckered kissing lips takes the place of a mouth. The lips form a compact ring with cupid's-bow lobes on top and a fuller lower lip, set back into the fruit's surface around the ball so the black shows through the middle. The strap runs around the head and across the front, outside the lips, lying against them as it passes over their corners and into the ball, so the lips sit behind it. The leaves are the star of the stand: a dozen broad blades plus a ring of shorter ones fan out beneath the fruit and lift it clear of the surface, giving the upside-down pose its height and silhouette. The body is scaled in staggered rows of triangular scales, kept clear of the face, so the fruit reads as a pineapple from any angle. And yes — the inverted pineapple is the classic swinger sign, worn here in full holiday dress. Use it as intended, or simply as a seasonal oddity. Made to hang A loop sits upright on the hat's peak, ready for a hook, ribbon or tree branch. With no base disc under the crown, the pineapple rests on its leaf tips — perfect for hanging, less so for standing on a shelf. The hat's tip droops to one side and ends in one large rounded bobble, so check clearance around the hook. Design notes Tall, wide leaf crown with 12 broad leaves and a ring of shorter ones; it doubles as the stand. Face: two open eyes with pupils and brows, a small nose, a black ball gag, and small red puckered kissing lips with a cupid's bow. The lips are sunk back into the face around the ball rather than standing proud of it, so the strap sits in front and the red shows as a ring. Strap wraps the back of the head and bands across the front outside the lips, resting against the face and covering their corners. Staggered triangular scales wrap the body in rows, with the face left smooth. Oversized hat with a thick trim of rounded puffs and a smooth bobble, finished with the hanging loop. The fluffy hat trim is the widest point, so check your bed size before printing.