C-Shaped Lamp Sleeve With Slots
Created today
Description
A single-piece C-channel sleeve that slides onto a 120 x 40 mm, 12 mm thick LED lamp panel and blocks light except through three evenly spaced slots.
The front plate and side walls are 2.4 mm thick, enough to be opaque in PLA. Back lips hold the panel in place, and the cavity has 0.2 mm clearance per side for a sliding fit. Two 6 mm bridges at the ends keep the strips between the slots connected.
- Cavity: 120.4 x 12.4 mm
- Slots: three, 6 x 40 mm, equal spacing
- Sleeve length: 52 mm
- Prints in one piece, front face down, no supports needed for the walls
- Fits the Bambu A1 mini bed
Images
More like this
Explore more in Desk & Tech →
Frostmourne Fantasy Sword Sculpture
A detailed gothic fantasy sword sculpture, laid flat on the print plate with the handle on the left and the blade pointing right. The pommel underside and the guard spikes are trimmed flush so the whole sword rests on the plate at z=0, which makes it sit stable while printing and lets it lie flat as a display piece. The blade runs about 157 mm long with a beveled, notched double edge, rune cuts down the middle and a thin central groove. The crossguard is the widest point at roughly 101 × 76 mm, built as a central block with curved horns, an upper horn, a rear spike and a forward spike. The grip is a core wrapped in raised rings, and the pommel carries a collar, radial spikes and a tail spike. Everything is modelled as one connected solid with the deep relief, sharp edges and layered ornament of the original design. Blade, crossguard and wrapped grip as one connected piece Beveled double edge with sculpted runes and a centre groove Curved horn crossguard with rear and forward spikes Round pommel with collar, radial spikes and tail spike Pommel and guard spike tips trimmed flat to sit on the plate Prints in millimeters; the thinnest spike tips taper down to about 1.5 mm The thin spike tips are the fragile part of the model — handle them carefully when removing the print, and thicken them if you want a sturdier piece.
Fidget toy à trois engrenages et boutons
Fidget toy mécanique compact, imprimable en PLA sans supports, sans ressort métallique ni pièce achetée. Les trois engrenages sont en prise : en tourner un entraîne les deux autres. Chacun porte une molette à encoches sur le dessus, et le troisième clique contre une languette flexible imprimée avec la base. Les engrenages tournent sur des axes séparés qui se clipsent par le dessus dans la base. Chaque roue repose à 0,5 mm au-dessus de la base et est retenue par la tête de son axe. Les trois boutons poussoirs se clipsent eux aussi par le dessus et se verrouillent avec un clic en position haute et en position basse. Base arrondie de 50 × 50 mm, hauteur totale 17 mm Engrenages de 14, 10 et 12 dents, module 1,5, jeu entre dents de 0,4 mm 3 axes clipsables, pied fendu avec ergot, jeu de 0,3 mm dans la roue 3 boutons avec 2 mm de course et deux crans de maintien Languette de cliquet imprimée avec la base Pièces à imprimer séparément : base, 3 engrenages, 3 axes, 3 boutons
Skeletal — Open-Frame Solar Tracker
Skeletal is a minimal-plastic, screw-free single-axis solar tracker: an open-frame base, a snap-in SG90 servo holder, a rotating platform and a ribbed mock solar panel, with a front bracket that holds two LDRs behind a central divider. Features 1.2 mm walls and an open-frame base to keep filament use low Servo holder with small chamfered snap lugs that grip the SG90 body, so it clicks in and pulls out without tools Cable slot from the base up to the rotating platform Panel centred on the rotation axis, with a raised rim, cell lines and a light ribbed underside Two LDR openings with a vertical divider in the front sensor bracket Print notes Printed flat in PLA, 0.4 mm nozzle, 0.2 mm layers Nano, SG90, horn and LDR dimensions are nominal. Measure the real parts and adjust the values at the top before printing.
iPhone 17 Pro Max Hülle mit Kameraausschnitt
Massive Schutzhülle für das iPhone 17 Pro Max: 4 mm Wände, 3 mm Rückseite und eine 3 mm breite Frontlippe, die höher über das Display steht. Kameraausschnitt, Öffnungen für die Seitentasten und eine Öffnung unten für den Anschluss sind vorgesehen. Die Hülle wird in einem Stück gedruckt. Auf der Druckplatte misst das Teil etwa 86,6 × 172 × 15,1 mm. Auf der Rückseite ist ein eigenes Logo eingraviert: ein Doppelring mit „09“ in der Mitte, umlaufen vom Bogen-Schriftzug „BORUSSIA DORTMUND“. Die Gravur ist etwa 66 mm breit und 1 mm tief. Von hinten gesehen ist sie lesbar und sitzt unter dem Kameraausschnitt. Bei 3 mm Rückseite bleiben 2 mm Material unter der Gravur. Es ist kein offizielles Vereinswappen. Passt für iPhone 17 Pro Max (Gehäuse 163,4 × 78 × 8,75 mm; die Hülle ist mit etwas Spiel darauf ausgelegt) Vor dem Drucken prüfen Die Lage der Kamera- und Tastenausschnitte ist geschätzt und nicht an einem echten Gerät kontrolliert. Miss vor dem Druck die Positionen an deinem Gerät nach und verschiebe die Ausschnitte bei Bedarf. Durch die dickeren Wände sind die Tastenöffnungen tiefer; die Tasten lassen sich dadurch schwerer drücken. Prüfe, ob das für dich noch passt. Für den Bau ist TPU statt PLA sinnvoller, weil es Stöße besser abfedert. Passt nicht Andere iPhone-Modelle, auch nicht die früheren Pro-Max-Größen mit anderem Gehäusemaß.
FoldDeck — Phone Shell and Printed-Hinge Keyboard Cover
FoldDeck is a clamshell-style phone-and-keyboard case built around a Galaxy A14 5G and a K808 Mini keyboard. The cover folds shut over the phone like a pocket flip-style mini laptop, and the hinge is printed as part of the design, so no pin, screw or other outside hardware is needed. Features Phone shell that replaces the phone's back, with snap hooks, a USB-C slot and flexing button covers Keyboard tray with screw posts for the K808 board Snap-on face plate with a window over the keys and touchpad Printed hinge: 3 mm round stubs on the tray knuckles seat in 3.6 mm blind bores in the shell knuckles Print notes Print the hinge parts with the stubs lying along the bed PETG or ASA is recommended for the snap hooks and hinge Port, button and camera positions are placeholders until measured
Nothing Phone (1) Case with Flipper Zero Cradle
A snap-on case for the Nothing Phone (1) with an integrated cradle on the back for a Flipper Zero. The phone enters from the screen side and is held by a 1.5 mm lip, while side-button slots and a bottom opening keep the buttons, USB-C port and speaker clear. The cradle sits on the lower two-thirds of the back, clear of the camera, and holds the Flipper Zero with snap ridges and finger notches. Corners on both the case and the cradle are rounded generously for a softer outline. Specs Phone fit: Nothing Phone (1); open front with a 1.5 mm retaining lip; side-button slots; USB-C and speaker opening. Back window: opening over the camera and glyph area. Flipper cradle: lower two-thirds of the back; 13 mm pocket height; port slots at both ends; finger notches on the long sides; snap ridges to hold the Flipper Zero. Flipper clearance: the Flipper Zero is 25 mm thick, so about half of it sits above the cradle rim. Corners: case outline 11 mm radius, cradle 10 mm radius; pockets and screen opening rounded to match; the cradle rim's top edges are still square. Overall size: the case is about 80 mm wide and 164 mm tall; the cradle is about 46 mm wide and 106 mm tall. Wireless charging: the cradle covers the phone’s wireless-charging area. Printing: print screen-side down with the cradle opening facing up. TPU is recommended for the 1.5 mm lip; PLA makes the lip stiff. Print status: this version has not been test-printed.