Scatola con foro e alette laterali
Created today
Description
Scatola rettangolare con fondo aperto che si avvita di lato su un mobile senza spostarsi o ruotare. Spigoli netti con piccolo smusso, niente raccordi tondi.
Misure
- Corpo: 40 × 20 × 60 mm, pareti da 2,4 mm
- Foro centrale sul top: 13 mm
- Due alette sul lato posteriore, 2 fori da 3,4 mm ciascuna (viti M3)
- Alette con finestra centrale per risparmiare filamento
- Stampa: fondo aperto verso il piatto, senza supporti
Images
More like this
Explore more in Home & Fixtures →
T-Post Cap With 3-Inch Round Platform
A slip-on cap for a steel T-post: 4 in tall, with a T-shaped socket that drops over the post and a 3 in round platform, 1/4 in thick, on top. Fits Steel T-posts, matched to the T-socket below. The socket is a T: a 36 mm crossbar, 7 mm wide at the stem entry, with a 7 × 30 mm stem running down, and a 4 mm wall following that T all the way around. Takes the place of a plain post cap and adds a flat, 3 in round surface on top of the post. Check before printing The socket is the whole fit, and its numbers are a starting size, not a standard — T-posts differ in flange width and web thickness between manufacturers and post weights. Measure the post you intend to use across the crossbar, across the stem, and across the full depth, then set the socket to those sizes plus a little clearance for paint and burrs before you commit filament. Nothing else on the part affects fitment. Does not fit Round posts, wooden 4x4 posts, or any post without a T cross-section. T-posts whose crossbar or stem is wider than the socket above — T-post profiles are not interchangeable, so do not assume a fit from the post name or the post weight alone. The cap prints as a single piece, 76 × 76 × 102 mm overall.
Патрубок Ø45 с раструбом Ø48
Пластиковый патрубок с небольшим расширением на одном конце, под соединение с трубой того же диаметра. What it's for Соединительный патрубок для трубопровода или воздуховода. Основная часть имеет внутренний диаметр 45 мм, а на конце есть раструб 48 мм, в который вставляется другая труба. Dimensions Общая длина: 140 мм Основная часть: длина 120 мм, внутренний Ø45 мм Раструб: длина 20 мм, внутренний Ø48 мм Толщина стенки: 3 мм (наружный Ø51 и Ø54 мм) Внутри есть плавный конический переход между диаметрами. Remix ideas Изменить толщину стенки под нужное давление. Добавить ребра жёсткости или упорный бортик. Сделать раструб на обоих концах.
Bug Zapper Battery Cover 27.65 x 60 mm
Sliding battery compartment cover plate for a bug zapper, 27.65 x 60 mm. A locating lip sits in the compartment opening, a latch tab sits at one end, and two low retention tabs at the opposite end keep the cover from falling out. Plate: 27.65 x 60 x 2 mm, chamfered edges Lip: 23.65 x 56 mm, 3.8 mm total height Retention tabs: two, 5 mm wide, flush with lip height, at X = ±8 mm Latch tab: 10 mm wide at the +Y end Grip grooves on the outer face Dimensions are estimates; verify against the original opening
Tampão com travas para abertura de pontas semicirculares
Tampão para abertura de pontas semicirculares que não fica solto: cobre o vão e trava por pressão nas quatro laterais — sem parafuso, sem fita e sem cair quando alguém esbarra. As travas são flexíveis e ficam embutidas no corpo, com um ressalto de 1,4 mm que pula para dentro da abertura e segura o tampão no lugar. Medidas que decidem o encaixe Abertura coberta: 27 × 114 mm, com pontas em semicírculo de raio 13,3 mm; o corpo tem 26,6 × 113,6 mm, já com a folga de encaixe. Aba de 2 mm em volta: assenta na borda e impede o tampão de afundar. Quatro travas embutidas: 30 mm em cada lado comprido e 12 mm em cada ponta, com ressalto de 1,4 mm que termina em 7,5 mm. Espessura total: 8 mm, contando a aba — o perfil fica baixo, rente à superfície. Peça completa: 32,6 × 119,6 × 8 mm. As travas das pontas ficam sobre uma superfície curva; confira se a abertura real tem o mesmo perfil antes de imprimir. Para imprimir Sai em uma peça só, sem montagem; nada de parafusos ou cola. As travas são finas e precisam de um material que ceda um pouco — PETG funciona bem; PLA muito rígido pode rachar a trava no primeiro encaixe. Imprima com o lado da aba para baixo, apoiado na mesa, para as travas ficarem limpas. Se o encaixe sair apertado ou folgado demais, ajuste a folga antes de mexer nas travas.
Antenna Cover With Mounting Flange
An antenna protective cover that keeps weather and knocks off the antenna: a hollow cylinder with a domed top, open at the bottom, on a flat bolt-down flange. Total height: 115 mm including the 4 mm flange Body: 50 mm outer, 46 mm inner diameter (2 mm wall), dome radius 25 mm blending tangentially into the cylinder Flange: 72 mm diameter, 4 mm thick Holes: four 5 mm through-holes in a square, 43.1 mm between adjacent centres Print: open end down on the flange, no supports needed, 3+ perimeters recommended
Fly Screen Frame Snap Lock for Wall Gap
A fly-screen frame snap lock holds the screen frame in a narrow gap between wall and frame without screws. The frame presses past two angled lips into a 10.4 mm channel sized for a 10 mm frame, and the back has a shallow inset so a glue strip sits flush against the wall. Fit: 10.4 mm channel for a 10 mm frame, with 0.4 mm clearance; the frame snaps in from above past the lips. Wall gap: 5 mm tall overall, sized for a 0.5 cm gap. Glue pocket: 0.8 mm deep, 24 × 11.4 mm recess on the back, so the glue strip does not hold the clip off the wall. Footprint: 30 × 15.4 mm against the wall.