Description
What it's for
A small solid block for use as a spacer, shim, test piece or placeholder.
Dimensions
- Length: 15 mm (X)
- Width: 4 mm (Y)
- Height: 4 mm (Z)
- Edges chamfered 0.4 mm
Remix ideas
- Add a through hole for a screw or string.
- Increase the chamfer for a softer look.
- Engrave a label on the front face.
Images
More like this
Explore more in Workshop & Tools →
5 x 5 x 1 mm Square Block
A plain square block measuring 5 mm by 5 mm by 1 mm, flat on the bed and ready to print. Remix hooks Footprint: 5 x 5 mm is the starting value. Change it to make a tile, spacer or shim. Thickness: 1 mm is about five layers at 0.2 mm. Raise it for a sturdier piece. Edges: Add a small chamfer or rounding for a softer look. Keep it under 0.5 mm at this size. Pairs with: Use it as a test cube for tolerance checks, or as a base for a hole, text or a peg.
Plain Square Block
A plain square block, 55 × 55 mm and 10 mm thick, with no grooves or other features. Footprint: 55 × 55 mm Thickness: 10 mm Flat base, prints without supports Suitable as a simple spacer, base plate or test piece.
U profilis, 60 mm tarpas, aukštos sienelės
U formos laikiklis, kuriame detalė neslysta į šonus: 60 mm tarpas tarp sienelių, 10 mm sienelės ir dugnas, 50 mm pagrindo plotis. Matmenys Vidinis tarpas: 60 mm Sienelių ir dugno storis: 10 mm Sienelės virš dugno: 60 mm (pailgintos 50 mm) Bendras dydis: 80 × 50 × 70 mm Spausdinimas: dugnu ant stalo, atramų nereikia
60 mm Square With Lengthwise Side Slots
What it's for A 60 mm square block with a thin slot cut into two opposite sides, useful as a test piece, a card or shim holder, or a slotted insert. Dimensions Footprint: 60 × 60 mm Height: 10 mm Slots: 5 mm deep, 0.4 mm wide, running the full length of each of two opposite sides, at mid-height Remix ideas Change the slot width to fit a specific sheet or card thickness. Add slots on the other two sides. Vary the block height or slot depth.
Bracelet Link Fit Gauge Block
A bracelet repair print that turns out too tight or too loose wastes hours. This fit gauge block is a 15-minute test piece that checks the fork slot and pin bores before the real part gets printed. Key numbers Block: 14 x 32 x 6 mm, origin at center, 1.2 mm edge fillets Fork slot: 5.2 mm wide, 12 mm deep, open at the -Y end, flat end wall at Y = -4 Prongs: 4.4 mm wide each Bores: Ø1.6 along X at Y = -10 (through both prongs) and Y = +10 (solid section) Tongue sample: 4.4 x 4.6 mm, 8 mm long on the +Y end, 0.9 mm end fillets, Ø1.6 bore at Y = +19 (40 mm overall) Printing Flat on the bed, PLA or PETG, 0.4 mm nozzle, 0.2 mm layers 4+ walls, 100% infill, 3 mm brim, no supports, 40 mm/s or slower Ream both bores once by hand with a 1.5 mm drill bit Checks A bracelet tongue link should enter the slot with slight friction. An original pin should slide through the -Y bore.
Sleeve — 0.385" OD Spacer Tube
Sleeve is a plain, precise hollow cylinder sized in inches: a straight-through bore and a clean outer wall, ready to use as a spacer, bushing or standoff. Dimensions Outer diameter: 0.385" (9.78 mm) Inner diameter: 0.26" (6.60 mm) Length: 0.75" (19.05 mm) Wall thickness: about 0.0625" (1.59 mm) Print notes Print standing on end, no supports needed. Bore may print slightly tight; ream or scale up a touch if fit matters.