Made by VertexAdze
Created 3 months ago
Description
An ultra-minimalist, single-piece light stand designed to slip effortlessly under a terrarium. The wide, flat base is held secure by the weight of the glass, while a slender 12mm pillar rises up to suspend an 8x8 LED matrix squarely over the enclosure.
Photos
Technical views
StrapSlot is a rectangular slot ring made for velcro straps — a buckle ring, strap keeper, or loop in one compact part. The internal opening is a clean 20 × 6 mm slot, and the 4.7 mm body uses 4.5 mm walls with rounded corners for a tidy outer profile. A 1 mm chamfer on the outer top and bottom edges softens the outside of the ring, while the slot edges stay square. Use it to keep a strap flat and contained, or as a replacement ring where a rectangular slot is needed. Dimensions | Feature | Size | | --- | --- | | Ring (each) | 29 × 15 × 4.7 mm | | Internal slot | 20 × 6 mm | | Wall thickness | 4.5 mm | | Outer edge chamfer | 1 mm on top and bottom | | Slot edges | Square | | Corners | Rounded | | Full set footprint | 63 × 55 mm, 4.7 mm tall | In the set Six identical rings, arranged in a 2×3 grid with 5 mm gaps between them. The whole set sits flat on the plate at a single 4.7 mm height, so it prints as one batch. Snap or separate the rings after printing to use them individually. Fit notes The 20 × 6 mm slot is the critical fit dimension; check your strap width and thickness against it. The 4.7 mm overall thickness sets the ring depth. The 4.5 mm walls, rounded outer corners, and 1 mm outer-edge chamfer define the outside shape.

A raised feeding platform in the spirit of a low mesa: a broad, tapered block with two round recesses cut into the top, built to lift a pair of 160 mm pet bowls to 120 mm so an older dog with dodgy hips can eat without stooping. The bowls drop into their rings and stay put, so a shove across the kitchen floor doesn't send them travelling. Wide cross feet at each end extend the footprint to 270 mm front to back, giving the stand a planted, anti-tip stance. Design notes Height: 120 mm overall Recesses: two, 164 mm diameter (160 mm bowl plus 4 mm clearance), 25 mm deep, with a chamfered lip for easy drop-in Spacing: 40 mm between the two recesses Footprint: 460 mm long, tapering upward, with a hollow underside to save material Anti-tip feet: 10 mm thick cross feet, 270 mm deep, at both ends Print notes At 460 mm long, the stand is larger than most print beds. Plan on a large-format printer or split it into sections. Bowls with a different diameter need the recess size adjusted to match.

A table lamp stand with a twisted six-lobe column rising from a round base to a cup that holds a standard E27 lamp socket. A 12 mm bore runs down the centre and a 7 mm channel carries the cable out the back of the base, so the wiring stays hidden. Remix hooks Socket pocket: 40.6 mm diameter, 26 mm deep. Measure your socket body and adjust socket_d before printing; many holders vary by a millimetre or two. Twist and lobes: 120° twist, 6 lobes. Change the twist angle for a gentler or more dramatic spiral, or the lobe count for a different silhouette. Height: the column is 140 mm; total height is about 182 mm. Taller columns suit larger shades. Base: 120 mm diameter, 8 mm thick. Widen it or add weight (coins, steel washers) for large shades. Set-screw hole: a 3.2 mm cross hole near the cup top is there for an M3 grub screw to lock the socket. Pairs with: an E27 socket with threaded nipple or clip-in body, a fabric cord with inline switch, and any E27 drum or cone shade. Print upright without supports. Use mains-rated, certified electrical parts, and a low-heat LED bulb rather than incandescent.
A hollow pipe that bends 70° along a 70 mm centreline and then splits into two diverging branches. The main bore is Ø42 with a 3 mm wall (Ø48 outside), giving a bend radius of roughly 57 mm. Where the bend meets the branches, the junction is stretched into a long egg-shaped blend — about 76 mm along the flow and 62 mm across — so the outside runs smoothly from the bend into each branch and the Ø42 bore narrows gradually into the two Ø33 bores, with no step or flat seam at the joint. On the print plate the two smaller branches lie flat and fan out sideways, side by side at ±17°, while the big curved pipe rises from them and bends upward, leaving its Ø42 inlet at the top of the bend rather than on the plate. The branches leave from either side of the junction rather than a single shared point, and the gap between them narrows quickly toward the blend, so only the outer stretch of each pipe stays clear for a hose — about 16 mm of clear space at the open ends, on centres roughly 56 mm apart. The whole part prints as a single hollow form with the branches already joined to the curve — no separate pieces or assembly. As it sits on the plate it measures about 92.6 × 141.2 mm with a height of about 69.9 mm, so check that against your bed before slicing. Keep the internal passages free of supports or bridging material so the flow stays unrestricted. Main bore: Ø42 inner, Ø48 outer, 3 mm wall Bend: 70° over a 70 mm centreline (≈57 mm radius), rising upward Branches: two, at ±17°, Ø38 outer, Ø33 inner (≈2.5 mm wall), 62 mm long, lying flat and fanning sideways Junction: stretched egg-shaped blend, approx. 76 mm along the flow and 62 mm across, feeding both branch bores without a step Branch spacing: ≈56 mm centre to centre, ≈16 mm clear at the open ends Footprint on the plate: approx. 92.6 × 141.2 mm, height approx. 69.9 mm Use it where a single round duct has to turn a corner and then divide into two angled outlets of a smaller diameter that each take a hose.
Hideaway ist eine kleine, oben offene Box mit Haken, die über einen Türrahmen gehängt wird und eine Batteriebox für Lichterketten verdeckt. Der Haken sitzt an der Rückseite, der Kabelausschnitt wandert seitlich aus der Box, damit die Vorderwand geschlossen bleibt. Maße Innenraum: 62 × 30 × 24 mm (passend für eine 3×AA-Batteriebox) Haken: für Türrahmen von ca. 20 mm Dicke, 40 mm breit Wandstärke: 2,4 mm Kabelausschnitt: 8 × 8 mm in der rechten Seitenwand, knapp über dem Boden Hinweise Ein Teil, kein Deckel – oben offen Vorderwand geschlossen, Kabelauslass seitlich Ohne Stützen druckbar, Rückseite flach auf das Druckbett
Replacement two-way joiner for the top-front-center of a fiberglass-rod printer enclosure. It splices two nominal 8.2 mm rods end-to-end and carries a flat-lying arm with a screw boss for a Sercomm RC8110 camera. Print it as one piece with the arm flat on the bed, then rotate the part about the rod axis during installation to aim the camera downward and toward the bed center. Specifications Rod sockets: 8.35 mm ID, 30 mm deep per side, 0.5 mm entry chamfers, separated by a 3 mm solid center stop; 63 mm overall sleeve length. Sleeve: approximately 14.35 mm OD with 3.0 mm wall thickness. Arm: 20 mm wide and 6 mm thick, extending 50 mm from the sleeve, with a root block and gusset blending it into the sleeve. Camera boss: 28 mm diameter and 6 mm thick, with a 6.6 mm through-hole and a 12 mm × 2 mm counterbore for a 1/4"-20 camera screw. Print footprint: 63 × 71.2 × 14.4 mm as oriented on the plate; the teardrop socket bores and flat arm are intended to print without support. Fit: press-fit for measured 8.19–8.20 mm rods; PETG wall thickness is sized to resist splitting and bending from the tensioned enclosure fabric.