Support-Free Braided Crucifix Pendant
Created today
Description
Pendants that look good from the front usually refuse to sit flat on a print bed, leaving you picking stringy supports out of fine details for half an hour. This cross solves that by keeping a meticulously carved face and an intertwined braided rope lashing, while silently shaving the entire rear face perfectly flush.
It drops right onto the build plate and prints in one clean shot.
- Dimensions: 34 mm wide, 55 mm tall
- Mounting: Heavy-duty 3.5 mm integrated through-bore, practically un-snappable
- Printability: Zero supports needed. The back is sliced flat so it anchors perfectly to the bed.
Images
More like this
Explore more in Keychains & EDC →
FlexiLink — Llavero Articulado TAMARA
Este es un llavero articulado de impresión print-in-place que no requiere soportes ni montaje. Las letras conforman el cuerpo de los propios eslabones, y se unen mediante un sistema de pasador cautivo oculto con holguras diseñadas para liberar el movimiento tan pronto como la pieza termina de imprimirse. Características Legibilidad mejorada: Los pasadores se conectan directamente a los laterales de las letras, manteniendo el interior limpio. Articulaciones sueltas: Diseñadas con 0.4 mm de tolerancia, pensadas para la calibración habitual de PLA en impresoras modernas. Sin ensamblaje: Todo el llavero se imprime como un solo cuerpo que se pliega. Anilla integrada: El extremo cuenta con una gaza con espacio para una anilla estándar de llaves.
Chubby Sitting Hamster Keychain
A compact, sitting hamster figure modelled with exaggerated, rounded proportions for a chunky silhouette. The base is sheared flat to allow support-free printing directly on the build plate, and a reinforced loop is integrated into the upper back of the head. Dimensions: ~28mm wide, 30mm tall. Keyring Loop: 3.2mm horizontal bore, heavily chamfered outer ring. Print Settings: Print upright. The limbs and facial features intersect closely with the main body to minimise overhangs; no supports are required.
Fidget
What it's for A fully print-in-place fidget roller inspired by continuous-motion hand toys. It features two heavily grooved outer cylinders captured on a rigid internal frame. Built to be rolled continuously in one hand to keep fingers busy. Dimensions Overall size: 37 mm wide, 63 mm tall, 22 mm deep. Rollers: 22 mm diameter, 50 mm tall with 20 scalloped grip grooves. Clearance: Designed with a 0.5 mm gap top, bottom, and radially around the axles for a free spin immediately off the build plate. Print notes Prints completely vertically without supports. The top frame link is designed with a flat bottom to bridge cleanly across the two internal axles without adhering to the rollers beneath it. Once finished, a firm twist breaks any minor stringing and frees the rollers.
Sifflet Tactique Double Chambre
Un sifflet de survie compact et puissant, construit autour d’une architecture à double chambre. Imprimable sans aucun support, il utilise deux cavités de résonance de longueurs différentes pour générer une dissonance acoustique perçante. Pour les remixeurs Ce design est purement mathématique et conçu pour être ajusté : Pitch et Dissonance : La longueur des chambres (actuellement 41 mm et 47 mm) dicte la fréquence. Raccourcissez-les pour un son plus aigu. Coupe du sifflet (Fipple) : L'angle de la rampe est fixé à -18 degrés et le bord d'attaque divise le flux d'air à Z=11.0. Si votre imprimante a tendance à sur-extruder, ajustez la hauteur de la fenêtre de frappe pour garantir que l'air ne soit pas étouffé. Grips : Les rainures latérales et supérieures sont de simples soustractions itératives, faciles à remplacer par des logos ou du texte plat.
Pocket Multi-Fidget Block
What it's for A dense, multi-function pocket fidget block that packs six tactile mechanisms into a single footprint. Designed to be printed entirely flat without supports, it features a print-in-place captive joystick, a spinning side-wheel, and two cantilevered clicky buttons. The front edge houses a deep hidden storage slot containing a flat-packed basketball kit. The backboard (complete with a rubber band hook on the rear) slots into the top of the block, and the rim snaps firmly into the backboard. Finally, one quadrant contains an internal hollow tank cavity with a threaded fill plug and a side spout. The top wall of the tank is intentionally thin (0.8mm) with a tactile button pad—pressing it lightly flexes the roof, simulating a squirt-pump mechanism. (While functional in TPU, printing in PLA serves as a satisfying, slightly yielding fidget button). Dimensions Base Block: 60 × 60 × 18 mm. Storage Slot: 46 mm wide, 58 mm deep, 4.5 mm tall. Backboard: 30 × 25 mm (excluding base peg). Rim: 18 mm outer diameter. Assembly Print Settings: No supports required. Ensure your printer is dialed in for 0.4mm print-in-place tolerances so the joystick and spinner break free smoothly. Hoop: Slide the backboard out of the front slot, insert the peg into the slot on the top deck, and press the rim peg into the backboard hole. Tank: The included friction plug seals the top fill hole.
VortexCore — Inel Giroscopic
Un model giroscopic compact format din patru elemente concentrice, creat pentru a fi imprimat direct articulat. Fără asamblare posterioară. Pivoții conici sunt calculați la o toleranță generoasă, permițând fiecărui inel să se rotească liber pe axa sa de îndată ce este ridicat de pe patul de imprimare. Dimensiuni Diametru total: 60 mm Înălțime: 10 mm Toleranță îmbinări: ~1.2 mm diametral Detalii de printare Se printează fără suport (no-supports). Designul pivoților folosește unghiuri de 45 de grade specifice printării FDM în sistem print-in-place, garantând că sferele interioare nu necesită susținere suplimentară pe axa Z. După finalizare, este suficientă o ușoară presiune pentru a dezlipi inelele unele de altele.