Tapered Bagel Shell
Created 1 months ago
Description
A bagel shoved into a backpack always turns into a flat puck, and a square tub takes up too much room. This hard clamshell is shaped precisely for the bagel itself—tapering in at the base so it doesn't waste space, with a central mounting cone that keeps the bread from sliding around and slamming against the walls.
It prints fully open as one piece, snapping shut with a friction latch.
Fit Details
- Max Bagel Width: 110 mm
- Max Bagel Height: 45 mm
- Print Requirements: No supports needed; prints flat on the bed.
Images
More like this
Explore more in Kitchen & Bathroom →
Toy Story Sky Cloud Cookie Cutter
A cookie cutter echoing the wallpaper clouds from Andy's room: a big bump on the upper left, smaller puffs along the top and a long flat base. The centre is open so dough passes straight through. 15 mm tall wall, about 1.2 mm thick, thin clean cutting edge on the flat bottom Widened rim at the top for pressing by hand About 100 mm wide, prints flat with no supports
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Sink Caddy With Drain Slots
Sponges and brushes left in a flat tray sit in a puddle and go sour. This sink caddy lifts them on ribs over a slotted floor so water runs out, and a separate tall holder takes a brush upright. Key numbers Tray: 200 x 110 x 45 mm, 2.4 mm walls Floor: 2.5 mm with 9 drain slots, plus 4 mm ribs to keep items off the surface Front notch: 60 mm wide, lets water pour off the front edge Brush socket: 48 mm square, inner opening 44 mm Removable holder: 40 x 40 x 100 mm with side slots for drainage; 2 mm clearance in the socket Printing Print the tray flat, no supports Print the holder upright 0.2 mm layers, PETG suggested for wet use
CornerSlide — Shower Basket
This is a custom-fit modular shower basket meant for standard glass partitions. The L-shaped caddy hugs the corner, saving space while giving you plenty of room for soap and bottles. Features Heavy Drainage: 20x8 grid cut deep through the floor means zero water pooling. Adjustable Hangers: Print-in-place T-slot sliders let you click the hook to the exact width of your glass. Rugged Base: Printed flat to ensure the hangers won't snap under tension. Easy Print: Built in separate pieces to maximize bed adhesion and strength. Print Notes Lay the sliders flat. The rails have a slight overhang, so throwing some standard supports under the T-slot stem will help keep it crisp.
Antalya Kebap Untersetzer 3.0
Runder Getränkeuntersetzer im Kebap-Stand-Look: Die Schrift ANTALYA KEBAP II steht 1 mm erhaben auf einer glatten Fläche, umgeben von einem hohen Rand, der Kondenswasser und Verschüttetes im Zaum hält. Durchmesser 100 mm, Boden 5 mm stark Umlaufender Rand bis 6 mm Höhe Schrift 1 mm erhaben, Bebas Neue Die Schrift endet auf Randhöhe, daher bleibt oben alles bündig
Obsidian — Ribbed Can Cooler with Handle
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports. Dimensions Inside diameter: 68 mm Inside height: 105 mm (above a 3 mm base) Wall: 2 mm, base: 3 mm Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel Features Diagonal ribs outside, perfectly smooth bore inside Rounded top rim Broad, rounded handle, 24 mm wide Flat front panel, 40 × 66 mm Print notes Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers No supports expected; fits a 180 mm build volume