Made by FoilMoose
Created 3 months ago
Description
A custom replacement L-bracket designed to hold a 626ZZ ball bearing at the top of a cross-flow fan rotor in a tower unit. Built to secure the 6mm fan shaft while maintaining precise wall clearance.
Because the bearing housing now protrudes 3mm past the bottom of the main arm, the model is lifted so the lowest point rests on the print bed. You will need to enable supports under the flat arm, or rotate the part manually in your slicer if you prefer a different print orientation.
Images
A 25 mm square corner block, 8 mm tall, with a quarter-circle channel on top that seats a 10 mm LED strip and turns it 90 degrees. Made for under-shelf lighting where the strip needs to follow an inside corner without kinking. The underside is flat, so it takes adhesive tape or double-sided foam. The channel is 10 mm wide and 4 mm deep, with a 12.5 mm centerline radius. It enters and exits through the two sides that meet at the far corner. Vertical corners carry a 1 mm chamfer. Remix hooks Block size (25 mm): the main lever. A 35 mm block with a 17.5 mm centerline radius gives a gentler bend for stiffer strips. Centerline radius (12.5 mm): keep it at half the block size so the channel meets the edges, or shrink it for a tighter turn. Channel width (10 mm): add 0.3 to 0.5 mm of clearance for strips with thick silicone sleeves, or narrow it for bare strips. Channel depth (4 mm): deepen it to sink the strip below the surface, or make it shallower and add a diffuser lip. Height (8 mm): can be lowered to about 6 mm and still keep the 4 mm channel with a solid floor. Pairs with Straight strip sections between corners, with one bracket per inside corner. A snap-in diffuser cover cut to the same 10 mm channel width. A mirrored variant for the opposite corner direction. Print notes Print flat on the back, with no supports needed. Use PETG or ABS if the bracket sits near warm drivers.

GripRoot is a replacement cane tip for a 19 mm tube, built for the case where an old tip has worn through and started to clack. A wide 40 mm base spreads the load, a tapered body leads up to a deep socket, and a cross-hatch tread on the underside gives grip on wet floors. The grooves run straight out through the edge of the base, so water has a path to escape instead of pooling under the tip. Dimensions Base diameter: 40 mm, with a chamfered lower edge Overall height: 31 mm Neck diameter at the top: 29 mm Socket: 19.5 mm inner diameter, 25 mm deep Socket mouth: small flared lead-in to help the tube seat Tread Cross-hatch grid of grooves, 3 mm wide and 2.5 mm deep 6 mm pitch in both directions Grooves open at the base edge for drainage Print notes Designed for stiff TPU, printed base-down with no supports needed The 19.5 mm socket against a 19 mm tube gives roughly 0.5 mm of interference, which suits a flexible material Measure the actual tube before printing, since nominal 19 mm tubing often varies slightly Adjust socket diameter or groove depth if a tighter grip or a more aggressive tread is wanted
Hideaway ist eine kleine, oben offene Box mit Haken, die über einen Türrahmen gehängt wird und eine Batteriebox für Lichterketten verdeckt. Der Haken sitzt an der Rückseite, der Kabelausschnitt wandert seitlich aus der Box, damit die Vorderwand geschlossen bleibt. Maße Innenraum: 62 × 30 × 24 mm (passend für eine 3×AA-Batteriebox) Haken: für Türrahmen von ca. 20 mm Dicke, 40 mm breit Wandstärke: 2,4 mm Kabelausschnitt: 8 × 8 mm in der rechten Seitenwand, knapp über dem Boden Hinweise Ein Teil, kein Deckel – oben offen Vorderwand geschlossen, Kabelauslass seitlich Ohne Stützen druckbar, Rückseite flach auf das Druckbett
Replacement two-way joiner for the top-front-center of a fiberglass-rod printer enclosure. It splices two nominal 8.2 mm rods end-to-end and carries a flat-lying arm with a screw boss for a Sercomm RC8110 camera. Print it as one piece with the arm flat on the bed, then rotate the part about the rod axis during installation to aim the camera downward and toward the bed center. Specifications Rod sockets: 8.35 mm ID, 30 mm deep per side, 0.5 mm entry chamfers, separated by a 3 mm solid center stop; 63 mm overall sleeve length. Sleeve: approximately 14.35 mm OD with 3.0 mm wall thickness. Arm: 20 mm wide and 6 mm thick, extending 50 mm from the sleeve, with a root block and gusset blending it into the sleeve. Camera boss: 28 mm diameter and 6 mm thick, with a 6.6 mm through-hole and a 12 mm × 2 mm counterbore for a 1/4"-20 camera screw. Print footprint: 63 × 71.2 × 14.4 mm as oriented on the plate; the teardrop socket bores and flat arm are intended to print without support. Fit: press-fit for measured 8.19–8.20 mm rods; PETG wall thickness is sized to resist splitting and bending from the tensioned enclosure fabric.
A screw-on lid in the spirit of a big jar cap, sized to seal the wall bracket that takes a 6 inch portable AC hose. The inside carries a female thread that mates with the bracket's 145 mm male thread, so it twists on the same way the hose does. Design notes 12 mm pitch, 5 mm thread depth, 2.5 mm clearance over the 145 mm thread 155 mm outer diameter with a 3 mm closed top and thin walls to save print time Scalloped grip notches around the rim Prints open-side up or top-down; the thread is coarse, so a 0.4 mm nozzle is fine
StrapSlot is a rectangular slot ring made for velcro straps — a buckle ring, strap keeper, or loop in one compact part. The internal opening is a clean 20 × 6 mm slot, and the 4.7 mm body uses 4.5 mm walls with rounded corners for a tidy outer profile. A 1 mm chamfer on the outer top and bottom edges softens the outside of the ring, while the slot edges stay square. Use it to keep a strap flat and contained, or as a replacement ring where a rectangular slot is needed. Dimensions | Feature | Size | | --- | --- | | Ring (each) | 29 × 15 × 4.7 mm | | Internal slot | 20 × 6 mm | | Wall thickness | 4.5 mm | | Outer edge chamfer | 1 mm on top and bottom | | Slot edges | Square | | Corners | Rounded | | Full set footprint | 63 × 55 mm, 4.7 mm tall | In the set Six identical rings, arranged in a 2×3 grid with 5 mm gaps between them. The whole set sits flat on the plate at a single 4.7 mm height, so it prints as one batch. Snap or separate the rings after printing to use them individually. Fit notes The 20 × 6 mm slot is the critical fit dimension; check your strap width and thickness against it. The 4.7 mm overall thickness sets the ring depth. The 4.5 mm walls, rounded outer corners, and 1 mm outer-edge chamfer define the outside shape.