17 mm Pocket Capsule for a Nurofen Tablet
Created today
Description
A small two-piece capsule for carrying a single Nurofen Flex 400 mg tablet in a pocket. The cavity is sized so the tablet stands upright inside with about 2 mm to spare, and a push-fit lid closes over the body. The lid sits beside the body on the print plate.
Specifications
- Capacity: One Nurofen Flex 400 mg tablet, standing on end.
- Internal cavity: 13 mm wide × 20 mm deep.
- Overall height: About 28 mm including the floor and lid seat.
- Body size: 17 mm across × 28 mm tall.
- Lid size: 17 mm across × 8.8 mm tall.
- Pieces: Prints as two pieces — capsule body and push-fit lid.
- Lid fit: The lid plug is about 0.2 mm smaller than the seat on each side; check the fit after printing and expect it to vary with your printer.
- Tablet check: Sized around an assumed tablet of about 18 × 10 × 7 mm; measure your own tablet before relying on the fit.
Images
More like this
Explore more in Storage & Organization →
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
RigPot — Bankstick Jar with Rig Loops
RigPot is a 30 mm bore, 100 mm tall screw-top jar built for carp tackle. It has a 50 mm side clip for a 15 mm bankstick, and three half-round loops for hanging rigs. Features 30 mm inside diameter, 100 mm tall Screw lid printed separately beside the jar Bankstick clip, 50 mm long, 15.4 mm bore with a snap-in slot Three flat half-ring rig loops at 90°, 180° and 270°, both ends fused into the jar wall Print notes The jar, clip and loops print as one body The lid is a separate piece and prints beside the jar
Telescoping Tube Container with Detent
What it's for Two rectangular tubes, each closed at one end, that slide together lengthwise into a closed container. Small detent bumps keep it shut. Dimensions Interior when closed: 112 x 262 x 55 mm Overlap: 60 mm Each tube: about 163 mm long, fits a 250 mm plate lying flat Clearance: 0.4 mm per side Print notes Print each tube as its own job. They are spaced apart in the preview so they do not touch. The detent is a pair of small round bumps on the inner tube that click into matching dimples in the outer tube's walls. Remix ideas Add a finger notch on the rim. Deepen the dimples for a firmer hold. Add dividers inside.
Kaugummiautomat im Heißluftballon-Stil für 18-mm-Kaugummis
Der Kaugummiautomat gibt einzelne Kaugummis vorne aus dem Zylinderfuß aus. Die Kugel sitzt mittig über dem Fuß und lässt sich über einen abnehmbaren Deckel befüllen. Vier gerade, senkrechte Streben tragen die Kugel vom Fußrand bis in die Kugelwand. Ein Rohr führt von der Kugelmitte über einen schrägen Trichter zur Drehmechanik im Zylinder: Eine Drehscheibe mit einem Loch für je ein Kaugummi wird von außen durch die Seitenfenster gedreht, sodass pro halber Umdrehung ein Kaugummi zur vorderen Öffnung rollt. Vor der 22-mm-Öffnung liegt eine mitgedruckte Ablagerampe, die das Kaugummi auffängt und nach vorn führt. Gesamtgröße (Druckplatte): 82 × 91 × 129 mm Kaugummi-Durchmesser: ca. 18 mm Deckel: 55,8 × 55,8 × 19 mm, abnehmbar Drehscheibe: 55 × 55 × 20 mm, im Fuß mit ca. 0,3 mm Luft eingebaut Streben: vier Stück, gerade und senkrecht vom Fußrand bis in die Kugelwand Rohr: oben mittig unter der Kugel, unten zum versetzten Loch der Drehscheibe abgewinkelt; ein Trichter in der Kugel leitet die Kaugummis dorthin Ausgabe: 22 mm breite Öffnung vorn, davor eine 26 mm breite Ablagerampe mit 2 mm Seitenwänden, 20 mm Länge, 6 mm hoher Frontkante und Abfall von 4 mm auf 1,5 mm Druck: als ein Stück; im Bereich der Drehscheibe Stützmaterial einplanen oder die Scheibe nach dem Druck kurz lösen
Monster Kart box
A hinged-lid card game box for a deck of 63 × 88 mm cards, sized for about 50 cards. The lid pivots on a mechanical barrel hinge along the back: three knuckles on the box and two on the lid, interleaved and held by a removable 1.75 mm filament pin. A front snap latch keeps the lid closed, and the hinge axis sits behind the back wall so the lid corner clears the rear wall and knuckle supports through 120°. Beneath the card stack, a removable divider plate with a 20 mm finger hole covers a hidden 12.7 mm compartment for paper inserts or original drawings. The box and divider plate are plain black to limit AMS waste; only the lid top carries the four-colour relief artwork. Specifications Box: 72.4 × 106.8 × 45.7 mm overall; card space approximately 66 × 91 × 20 mm for about 50 cards. Hidden compartment: 12.7 mm high under the card stack, with four corner posts supporting the divider plate. Divider plate: flat and removable, 2 mm thick, with a 20 mm finger hole. Hinge: five interlocking 9 mm knuckles with 0.4 mm axial gaps; moving-part clearance approximately 0.3–0.4 mm; 2.1 mm bores on one straight coaxial axis. The axis sits 4.9 mm behind the back wall. A 1.75 mm filament pin feeds in from one end through a flared lead-in and is held by friction; the opposite end is closed 1.2 mm short of the face, so the pin is pulled back out from the entry side. Latch: two flexing front posts with sloped hooks snap into lid notches; a thumb tab at the front centre releases it. Lid artwork: red rectangular border; dark black/purple background; large white moon near the upper centre; black haunted-castle silhouette with varied pointed towers; black bat silhouettes that read mainly as two long curved wings with very small bodies, sharp tips and scalloped trailing edges; purple hills and mist; a curved purple path; angled MONSTER in white and KART in red with black outlines; a 16 mm interlocking TB monogram centred near the bottom — a white glyph inside a red disc separated by a 0.5 mm black gap. The T carries an 8 mm top bar and a 1.8 mm full-height stem. The B shares the stem as a flat left spine, with a smaller upper bowl and fuller lower bowl, a pinched waist, and D-shaped counters rather than circular holes. A gap of about 1 mm separates the T bar from the top of the B. Only black, red, purple and white are used. Printing: support-free geometry for a 0.4 mm nozzle; latch posts are 1.4 mm thick; bat membranes come to about 1 mm. In the TB monogram the upper counter is about 1.1 mm tall — check it on a first print. Assembly: three printed pieces — box, divider plate and lid — plus a 1.75 mm filament pin. The lid's colour layers are grouped as one multi-colour object for four-slot AMS printing.
Stickpot
A screw-top tackle jar in the spirit of a carp angler's bankstick kit: tall bore, flat slotted tabs at the base, and a half-circle arch standing on the lid for hanging rigs. Design notes 30 mm bore, 100 mm tall Bankstick clip now runs from the base of the jar upward, 50 mm long, with a snap-in slot Three flat slotted loops at the base, printing flat with no overhang Lid with a 6 mm wide half-circle arch, printed upside-down beside the jar