Created 21 days ago
Description
A classic apothecary-style storage box, 6" x 4" x 2", with a separate lid whose inner lip plugs into the body. The two pieces are laid out side by side for viewing and print as two separate jobs, so each fits an 18 x 18 cm bed.
Images
A hexagonal box with a matching lid, printed as two separate pieces. The box is 50 mm tall and 80 mm across the corners, with 2.4 mm walls and a 3 mm floor. The lid is a 3 mm hexagonal plate with a 6 mm hollow lip underneath. The lip sits inside the box opening with about 0.4 mm of clearance per side, so the lid stays put without a tight press fit. Box: 80 mm across corners, 50 mm tall, chamfered base edge Lid: 80 mm across corners, 3 mm plate, 6 mm inner lip Print the lid flat with the lip facing up No supports needed for either piece
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
Two-bay deck box for sleeved Yu-Gi-Oh! cards with a separate accessory bay for dice and other game items. A plug-in lid carries a Millennium Puzzle triangle with an eye and "Yu-Gi-Oh!" lettering in a regular-weight font. Millennium Items are raised on the outside walls. Card bay: 70 mm wide, for sleeved decks Accessory bay: 40 mm wide, with a cross divider separating dice from other items Front: Millennium Scale and Millennium Eye, 1.2 mm raised relief Back: Millennium Ankh and Millennium Ring Sides: Millennium Key (left) and Millennium Rod (right) Lid: flat plate with plugs for both bays, printed plate-side down
What it's for A hinged tackle box for bass fishing gear, with a locking front latch, removable thick dividers and a leaping bass on the lid with SMITH FISHING lettering. Dimensions Base: 240 × 160 × 50 mm, 4 mm walls, 3 mm floor Lid: 240 × 160 × 22 mm with raised artwork Dividers: 5 pieces, 2.6 mm thick, sliding in 3.2 mm grooves Hinge: 5 knuckles with a separate 4.2 mm pin Latches: 2 front latches with pivot pins Remix ideas Change the lettering to a different name Add more divider grooves for smaller compartments Swap the lid artwork for another species
Nook is a round pencil cup sized to hold pens, pencils, markers and short rulers upright on a desk. The design keeps a clean, fully circular profile — no flat back, no corners — so it reads as a plain cylinder from every side. What sets this version apart is a wall of openings cut all the way around and up the side: three staggered rows of small round holes that let you see at a glance what's inside, let the cup breathe, and keep the barrel light. At 80 mm across and 70 mm tall it takes a full handful of writing tools while staying low enough to reach into from a seated position. Dimensions Diameter: 80 mm, fully round Height: 70 mm Walls: 4 mm Footprint: 80 × 80 mm Side openings: 36 round holes, 10 mm across, in three staggered rows of 12, spread around and up the cup wall Features Full circle profile with no flat back — the same silhouette from any angle A staggered grid of 10 mm holes around the side wall, small enough to leave solid wall between them Base and top rim stay solid, so the cup holds its shape and stands straight Wide 80 mm mouth for pencils, pens, markers and short rulers 4 mm walls give it enough weight at the base to stay put while you pull a pen out Freestanding: it sits directly on a desk, shelf or tray with nothing to fix or hang Print notes Prints as a single piece with no supports. Print it upright as it sits on the plate so the walls and the round holes stay clean, or lay it on its side if you prefer a smoother inner surface and can accept a light support under the outer curve. A slightly wider brim helps on taller, narrow prints.
A round 88 mm ornament disc, 4.8 mm thick, with a grid of LEGO-compatible studs on the face and a hanging loop at the top. Printed in red, flat, with no supports. Remix hooks Stud diameter: 5.0 mm now (standard is 4.8 mm). Raise it to 5.05 for a firmer grip, or drop it to 4.9 if bricks sit too tight on your printer. Stud height: 1.8 mm. Taller studs give a deeper grip but need more bridging care. Disc thickness: 4.8 mm, or 1.5 LEGO plates. Use 3.2 mm for one plate or 9.6 mm for a full brick height. Disc diameter: 88 mm on an 8 mm stud pitch. The stud grid is cut to a 37 mm radius, which leaves a plain rim. Loop: 13 mm outer, 5.5 mm hole. Widen it for ribbon. Pairs with: 1x1 and 2x2 bricks, tiles, and small minifigure scenes.