90x60mm Campaign Magnet-final-final-super-final
Created 2 months ago
Description
A three-colour stepped campaign magnet formatted for a 90x60mm footprint. Designed to print cleanly with two manual filament swaps.
Fitment
- Magnets: Four 6.05mm x 3mm disc magnets, set into the rear face.
- Layer Heights: Blue base to 3.6mm, white layer to 4.6mm, red top layer to 5.6mm.
Features a classic bell-tower schoolhouse and a reshaped apple graphic flanking the bottom text line, with adjusted margins across the middle lines to tighten up the vertical spacing.
Images
More like this
Explore more in Keychains & EDC →
Safety Third Diamond Keychain
A keychain for the keyring that always ends up at the bottom of the bag: a diamond-shaped yellow warning sign with "SAFETY THIRD" in black on two lines, and a loop at the top apex for the ring. It is oversized on purpose, so it reads as a sign rather than a tag and is easy to find by feel and grab. Fit and print Overall size: about 97 mm across and about 107 mm tall including the top loop — big for a keychain, deliberately. Lettering: both lines are centred in the diamond at a size that keeps "SAFETY" inside the inner border, with a small gap at the top corners. Attachment: 6 mm hole through the plain yellow loop at the top apex; no black ring around the hole. Two-colour print: yellow base with the black border and text raised 0.8 mm; swap filament at 0.8 mm. Assembly: prints as one piece, with the black layer sitting proud of the yellow face.
Dawg Tee — Georgia Fan Golf Tee
The Dawg Tee is a Georgia fan golf tee in red and black, made for showing team colors out on the course. It stands 62 mm tall with a compact, shallow dish at the top to seat the ball, a black head, and four black bands breaking up the red shaft along most of its length. Below the bands the shaft tapers into a short, sharp point that starts easily in the ground. The narrow head keeps the silhouette tidy, and the alternating red-and-black blocking gives the tee a look that reads instantly from the tee box. Dimensions Overall height: 62 mm Shaft: 5 × 5 mm, 58 mm tall including the point, tapering from a 0.6 mm tip over the lowest 7 mm Head: black shallow dish, 14 mm across, 4 mm tall with a 0.8 mm recess Bands: four black rings around the shaft, 4.7 mm across, spaced roughly 7, 20, 28 and 40 mm up and together covering 38 mm of the shaft Features Slim, low-profile head that keeps the ball sitting close to the shaft Red shaft with a black head and four contrasting black bands Short, sharp point for pushing into the ground Prints as one solid piece — no separate parts to assemble Print notes The 0.6 mm tip is fine and fragile; print in a tough material and avoid forcing it into hard, compacted ground. Rounding the very tip slightly makes it far more durable at the cost of a little bite. The shallow 0.8 mm recess holds the ball more loosely than a deeper cup; deepen the recess if you want a firmer seat. Multi-color printing brings out the red shaft against the black head and bands; a single-color print still works but loses the contrast. The tapered shaft prints cleanly without supports.
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
35 mm Threaded Keychain Container, Rosette Lid
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
Pin de mano esquelética con dedo medio levantado
Pin con forma de mano esquelética cerrando el puño y con el dedo medio levantado. El dedo medio sube recto con sus tres falanges; el índice, el anular y el meñique quedan plegados hacia la palma. El pulgar va por detrás de los dedos plegados, así que solo asoma por el lado izquierdo y entre los huesos. Los huesos son blancos y de estilo realista: cada uno tiene una diáfisis fina y dos cóndilos redondeados en cada extremo, con una muesca central, y el extremo superior algo más pequeño. Las divisiones negras entre huesos marcan las articulaciones. En la palma hay cuatro metacarpianos y en la muñeca un grupo de huesos del carpo pequeños. La placa negra de 2 mm sigue la silueta de la mano y sobresale como borde. Los huesos van elevados 0,9 mm sobre ella, con la parte trasera completamente plana. La pieza mide unos 23 × 36 mm, así que queda 1 mm por encima de los 35 mm; el grosor total es de unos 2,9 mm. Para ajustarla al límite de 35 mm, reduce el borde de la placa. Placa negra plana de 2 mm; huesos blancos elevados 0,9 mm Huesos segmentados y separados por huecos negros de articulación, todos apoyados en la placa Sin piezas flotantes; se imprime como una sola pieza Sin soportes: la parte trasera es plana y los detalles se elevan desde la placa Huecos estrechos entre huesos; pensados para una boquilla de 0,4 mm
21mm Disk Holder with Snap Lip
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge