Created 1 months ago
Description
A precisely dimensioned rectangular charm featuring gently rounded edges and delicate engraved details. Designed to lie perfectly flat while capturing intricate central motifs.
Images
A print-in-place articulated dragon built on 6 mm balls in 7 mm sockets, with faceted hexagonal crystal clusters on the head, spine, legs and tail tip. Fit and clearance Joint: 6 mm ball in a 7 mm socket (0.5 mm radial clearance), 5 mm neck opening so the ball cannot pull out. Chain: 42 body segments at 12 mm pitch, plus four legs of two segments each. Check before printing: the laid-out dragon is roughly 350 mm long in its S-curve, so verify your bed size or scale it down in the slicer. Scaling below about 80% closes the 0.5 mm clearance. Not suited to Printers with a bed under about 250 mm without rescaling. Printing the crystals first: the model lies flat on the bed, crystals pointing up, flat horns on the bed. Fast, uncooled printing: joint gaps need slow, well-cooled layers.

A round Stitch-style head bead with two pointed ears, a lighter face patch, eyes and a nose, threaded by a vertical hole for cord or wire. Remix hooks Head size: the head radius is 13 mm (26 mm across). Scale it down for jewelry-sized beads; keep the hole at 3.5 mm or larger for cord. Hole diameter: 3.5 mm runs top to bottom between the ears. Widen it for paracord or narrow it for thin elastic. Ear angle and length: ears are about 21 mm long, splayed 55° outward. Lower the angle for droopy ears, or shorten them for a chunkier keychain bead. Colours: the head, face patch, inner ears and eyes are separate regions, so they suit multicolour printing with filament swaps. Pairs with: plain round spacer beads, a keyring clasp, or a row of beads for a bag charm.
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
Pin con forma de mano esquelética cerrando el puño y con el dedo medio levantado. El dedo medio sube recto con sus tres falanges; el índice, el anular y el meñique quedan plegados hacia la palma. El pulgar va por detrás de los dedos plegados, así que solo asoma por el lado izquierdo y entre los huesos. Los huesos son blancos y de estilo realista: cada uno tiene una diáfisis fina y dos cóndilos redondeados en cada extremo, con una muesca central, y el extremo superior algo más pequeño. Las divisiones negras entre huesos marcan las articulaciones. En la palma hay cuatro metacarpianos y en la muñeca un grupo de huesos del carpo pequeños. La placa negra de 2 mm sigue la silueta de la mano y sobresale como borde. Los huesos van elevados 0,9 mm sobre ella, con la parte trasera completamente plana. La pieza mide unos 23 × 36 mm, así que queda 1 mm por encima de los 35 mm; el grosor total es de unos 2,9 mm. Para ajustarla al límite de 35 mm, reduce el borde de la placa. Placa negra plana de 2 mm; huesos blancos elevados 0,9 mm Huesos segmentados y separados por huecos negros de articulación, todos apoyados en la placa Sin piezas flotantes; se imprime como una sola pieza Sin soportes: la parte trasera es plana y los detalles se elevan desde la placa Huecos estrechos entre huesos; pensados para una boquilla de 0,4 mm
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge