Anglewright — 90° L Profile
Created today
Description
Anglewright is a clean 90° L profile with unequal legs: 3 in along one axis, 2 in along the other, and 12 in tall. Both legs are 0.5 in thick, giving a simple right-angle section for corner bracing, spacing, or building up a frame. The form is a single continuous L, so the shape itself carries the function.
Dimensions
- Overall height: 12 in (304.8 mm)
- Leg lengths: 3 in × 2 in (76.2 mm × 50.8 mm)
- Leg thickness: 0.5 in
- Corner angle: 90°
Print notes
The 12 in height is the main constraint. Standing upright it exceeds most print beds; print it lying on its side instead. The flat L section gives a stable orientation without needing a special base.
Images
More like this
Explore more in Home & Fixtures →
Kampas — Mini pakaba su briaunomis
Kampas yra maža vaikiškų drabužių pakaba su stačiakampe kilpa. Pakelti galiukai ir papildomos briaunos galuose neleidžia petnešėlėms nuslysti. Savybės Stačiakampė kabinimo kilpa Pakelti galiukai 30° kampu Briaunos galų pakraščiuose Plotis 10 mm Spausdinimas Spausdinama gulint ant plokščios pagrindo dalies, be atramų.
Capstop — Magnetic Wall Bottle Opener
Capstop is a wall-mounted bottle opener built around a simple idea: the cap should not hit the floor. A flat back plate carries a cap-catching lip, and a recess behind the opening holds a disc magnet that grabs the cap as it comes off the bottle. The magnet pocket is sized for a 20 mm diameter, 5 mm thick disc magnet, with a small clearance so it seats without forcing. Two countersunk screw holes let the plate sit flush against the wall. Features Back plate, 60 mm wide and 100 mm tall, with chamfered edges Opener lip with a cap slot, projecting from the front face Magnet recess for a 20 × 5 mm disc magnet, located behind the opener Two countersunk screw holes for wall mounting Slim funnel and removable cup intended to sit below the opener to collect caps Dimensions Plate: 60 × 10 × 100 mm Opener lip: 40 mm wide, 14 mm projection, 8 mm thick Magnet pocket: 20.4 mm diameter, 5.2 mm deep Screw holes: 4.5 mm shank, 9 mm countersink Print notes Print the plate on its back or side; the opener lip prints best flat. PETG or ASA is suggested for durability against repeated cap contact. Secure the magnet with a drop of glue if the wall mount sees heavy use.
100x59 Oval Body Hole Cover with Snap Clips
Einsteckbare Abdeckung für eine ovale Öffnung von 100 × 59 mm in etwa 1 mm dickem Blech. Die Frontplatte ist vollständig geschlossen und liegt mit einem 3 mm breiten Auflageflansch rundum auf dem Blech auf; außen misst die Abdeckung 106 × 65 mm bei 2,5 mm Plattendicke. Auf der Rückseite zentriert ein Rahmen mit 2 mm Wandstärke und einer Innenöffnung von 96 × 55 mm als ovales Langloch mit Endradius 27,5 mm. Der Rahmen reicht 7 mm über den Flansch hinaus. Die vier flexiblen Clips – je zwei an den langen Kanten – haben 0,8 mm hohe Haken und angeschrägte Einführflächen; die Rastkante sitzt 7 mm über der Flanschfläche. Mit den verlängerten Federschlitzen baut die Abdeckung insgesamt 13 mm hoch. Bei 1 mm Blech bleibt zwischen Blech und Rastkante in Einsteckrichtung Luft; der Clip rastet erst nach 7 mm Einstecktiefe ein. Werkzeuglose Montage und Demontage Einteiliger Körper, keine Schrauben und kein Kleber Flansch nach unten drucken, in PETG oder ASA Clipsitz beim ersten Druck prüfen, da die Federwirkung des Materials schwankt
Veranda End Bay with Leaf Outline Infill
A rectangular end frame for a veranda run, built from two uprights, a top beam and a lower rail, with a decorative leaf panel set into the opening. The infill is a collage of large overlapping leaves drawn as open outlines. Each leaf has a centre rib and four angled side veins, so the panel reads as fine, see-through line work rather than a solid fill. Leaves sit at random angles and positions and are clipped flush at the frame, where edge leaves run into the posts, top beam and bottom rail. A leaf sits one third of the way in from the left post, just under halfway up the panel. Frame and infill print as one piece. What it's for Closes the end of a veranda run with a decorative open screen instead of a solid infill. The overlapping leaf outlines fill the panel with line work while leaving gaps open, so sightlines and airflow stay partly clear. The scattered leaf layout gives an organic, uneven look rather than a repeating geometric pattern. The layout is fixed, so the pattern is the same from print to print. Dimensions Overall frame: 120 × 150 mm, 12 mm deep. Infill opening: about 96 × 123 mm, 6.5 mm deep; the leaf collage fills it edge to edge. Leaves: roughly 50–105 mm long and 26–46 mm wide, with a 1.2 mm outline, a 1 mm centre rib and four side veins at 0.8 mm. Frame and infill print as one piece; no assembly required. Print notes Lay the frame flat on the plate and print it as a single piece. The leaf outlines, ribs and veins are thin line work; slow the outer walls if the printer tends to string across the gaps. Because the leaves are placed at random, a leaf near the edge may be held only by its neighbours rather than by the frame. Check the perimeter first when cleaning up the print. Remix ideas Change the frame proportions to suit a different veranda or porch opening. Reuse the leaf collage alone as a decorative screen or window insert. Simplify the leaf outlines for a bolder, less detailed screen. Swap the leaf shape for a different botanical outline while keeping the scattered layout.
83mm Desk Grommet with Sealed Hollow Body
A one-piece desk grommet for an 83 mm hole, with an off-center cable passage. The barrel drops through the desk and the 99 mm flange rests on the surface; 3 mm caps close the part at both ends and the interior is a sealed hollow, so it uses little filament for its size. A 14 mm cable hole sits 30 mm from the center, about 4 mm in from the rim, and passes through the flange and both caps. It takes most round power cables but will not pass a plug. Desk hole: 83 mm Barrel: 82.6 mm outside diameter, 20 mm tall Flange: 99 mm diameter Cable hole: 14 mm diameter, 30 mm from center, near the edge Wall and cap thickness: 3 mm; cable-hole wall: 2 mm Interior: sealed hollow cavity Fit: desk tops up to about 17 mm thick Print: one piece; no external supports; the enclosed cavity will bridge internally near the top of the void Overall footprint on the plate: 99 × 99 × 20 mm
CrestHook — 80 mm D-Ring S-Hook
CrestHook is an 80 mm S-hook made to bridge a D-ring and whatever needs hanging from it. Two opposing round hooks share the same crest-to-crest length, and each end has a 20 mm opening intended to clear a typical D-ring bar with room to spare. The hook is laid flat for printing, so the layers follow the curve rather than crossing it. Dimensions Overall footprint: 58 × 80 × 8 mm on the print plate Length: 80 mm crest to crest Hook opening: 20 mm at each end Wire section: 6 mm thick × 8 mm tall Print orientation: lies flat on the plate