70mm Desk Hole Cap, Hollow
Created today
Description
A hollow, fully closed cap for a 70 mm desk hole. A 69.6 mm barrel fits the hole and an 86 mm flange sits on the desk surface. Both ends are closed with 3 mm caps, and the interior is left empty to save filament.
- Barrel: 69.6 mm diameter, 20 mm tall
- Flange: 86 mm diameter, 3 mm thick, chamfered edge
- Caps: 3 mm solid at both ends
- Interior: sealed hollow, 63.6 mm diameter
- Print with the flange side down; no supports needed
Images
More like this
Explore more in Home & Fixtures →
Pool Noodle End Cap Plug
A pool noodle end cap that plugs the hole so water, sand and grit stay out of the foam, and the open end stops getting chewed up. The plug uses the same barbed shaft as the noodle connector, so it grips the foam instead of working loose. Key numbers Shaft: 22 mm diameter, 56 mm long, tip chamfered for easy starting Barb rings: four, 28 mm diameter, 14 mm apart, chamfered both sides Head: 70 mm diameter, 8 mm thick, rounded top edge, stops flush against the noodle end Sized for a roughly 25 mm centre hole; foam stretches over the rings Printing Print head-down on the plate, shaft pointing up No supports needed, the ring chamfers handle the overhang PETG or similar; 3 perimeters for stiffer barbs
100x59 Oval Body Hole Cover with Snap Clips
Push-in cover for a 100 x 59 mm oval opening in 1 mm sheet metal. The front plate is fully closed, with a 3 mm overlap flange all round (106 x 65 mm outer, 2.5 mm thick). A 2 mm wall locating frame (99.4 x 58.4 mm, 5 mm deep) centres the cover in the opening. Four flexible cantilever clips (two per long edge) have tapered lead-ins and 0.8 mm hooks that lock behind the sheet metal. Tool-free install and removal Single solid body, no screws or glue Print flange-side down in PETG or ASA
Vileda Broom Bar Hook
A bare metal broom top snags, and the mushroom-shaped anchor on a Vileda stick gives a plain hook nothing secure to grab. This replacement end cap sleeves 20 mm down over the sharp top of the stick, then snaps over the anchor with long leaf-spring arms and locking pads. The open hook sits centered over the sleeve so the broom hangs straight on a 27 mm bar, and the flared mouth catches the bar without needing perfect alignment. The hook arch is raised clear of the internal flex chamber, leaving solid plastic between the two cutouts. Fit and print Broomstick: fits a 25.3 mm Vileda stick; the sleeve drops 20 mm over the sharp top edge. Anchor: clears the 13 mm mushroom cap and locks around the 10 mm shaft; the 28 mm tall relief cavity gives the 1.75 mm leaf springs room to flex. Hook: open downward U-channel for a 27 mm bar, not a closed loop; the flared mouth helps catch the bar. Wall: solid plastic separates the flex mechanism from the hook cavity. Printing: lay the 2 mm flat plateau on top of the arch on the bed and print upside down; no supports, internal ceiling bridges. Material: PETG suits the flexing snap mechanism. Size: 31 mm wide, 63.5 mm deep, 118 mm tall as oriented for printing.
White 4 x 10 Inch Flat Vent Grill
Flat slotted vent grill, 10" x 4" with a thickness of 1/4". Two banks of eight through-slots are separated by a center rib for stiffness, inside a solid border. Size: 254 x 101.6 x 6.35 mm Slots: 8 per side, 5 mm wide, 112 mm long, rounded ends Border: about 10 mm solid on the long edges, 15 mm on the ends Print flat, no supports; PETG or ASA suits warm airflow Edges: 4 mm rounded vertical corners
12V-Stabschiene 6 mm Klemmplatte für Ø80 Spot
Zweiteilige Trägerplatte für einen runden 220V-Spot mit 80 mm Basis auf einem 12V-Stabsystem: zwei parallele Stäbe Ø6 mm, 35 mm Mitte zu Mitte. Die Oberplatte trägt den Spot, die Unterplatte klemmt die Stäbe von unten dagegen. Passt auf Zwei Rundstäbe Ø6 mm, Abstand 35 mm Mitte zu Mitte (Nuten Ø6,3 mm) Runde Spotbasis Ø80 mm (Senkung Ø80,4 mm) Passt nicht auf Stäbe mit anderem Durchmesser oder anderem Abstand Spots mit abweichendem Lochbild: angenommen sind drei Löcher Ø4,5 mm auf Lochkreis 60 mm Vor dem Drucken prüfen Lochbild des Spots und Stabdurchmesser nachmessen. Montage Sechs Schrauben M4 von unten durch die Unterplatte (Senkung für den Kopf) in die Oberplatte; Bohrung Ø3,4 mm schneidet das Gewinde selbst. Kabeldurchlass Ø14 mm in der Mitte. Beide Teile liegen mit offenen Nuten nach oben auf dem Druckbett, ohne Stützen. Ein 220V-Spot an einer 12V-Schiene braucht eine saubere elektrische Trennung. Das Druckteil ersetzt keine Schutzisolierung.
70 × 108 × 25.5 mm Box Snap-Clip Frame
Snap-clip mounting frame for a 70 × 108 × 25.5 mm box, with two 20 mm clips joined by a lightweight frame. Fit Clips sit 108.6 mm apart, inside to inside. Four 20 mm corner blocks locate the box sideways, with 0.3 mm of play per side. Three countersunk screw holes: one in each clip flange and one at the center. Check before printing Confirm the box measures 70 × 108 × 25.5 mm. It does not suit other sizes without changing the clip spacing and block positions. Structure The frame is 3 mm thick. It uses two edge rails, three crossbars and a center screw pad, and prints flat on its back.