Basgiath Riders Shield Keychain

Apple Watch SE 44mm Keychain Case

What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.

25 days agoRemix →

35 mm Threaded Keychain Container, Rosette Lid

Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.

11 days agoRemix →

21mm Disk Holder with Snap Lip

What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge

16 days agoRemix →

Portachiavi Famiglia Raganella con rilievo

Sei portachiavi con una raganella in rilievo e la scritta FAMIGLIA RAGANELLA, per distinguere le chiavi di casa senza provare tutte le copie. I sei pezzi sono disposti su due file da 3, con 40 mm tra un portachiavi e l'altro lungo X e 56 mm tra le file in Y: si stampano tutti insieme su un'unica piastra, pronti da separare e da agganciare agli anelli. La disposizione resta compatta e tra una piastra e l'anello della fila successiva rimangono pochi millimetri. Le zampe della raganella, davanti e dietro, sono abbassate fino a toccare la piastra del portachiavi, così non restano sospese. Misure e stampa Sei portachiavi in due file da 3 Passo di 40 mm in X, 56 mm tra le file in Y Ingombro totale sul piatto: 114 × 108 × 11,4 mm Piastra singola: 34 × 44 mm, spessore 3 mm Foro per l'anello: 5 mm Corpo della raganella e scritta in rilievo, circa 1 mm sopra la piastra; zampe a contatto con la piastra Stampa piatta, senza supporti, anche in PLA Note Lo spazio tra le file è stretto: se serve più margine attorno ai pezzi, si possono distanziare o stampare in due passaggi.

1 day agoRemix →

Pocket Snaplink Print-in-Place Carabiner

A compact, D-shaped snaplink in the spirit of the little accessory carabiners that hang off backpack straps and key rings. The 70 mm body carries a pivoting gate and a thin flexure spring that nudges it shut, all printed together in one go. Pop the gate open with a thumb, slip a key ring or bottle loop in, and let it snap back. Not rated for climbing or load-bearing safety use. Keep it to keys, bottles and bag clips. Design notes Size: 70 mm long, 38 mm tall, 8 mm thick. Gate: hinged at the right end, swings inward about 32° for a roughly 12 mm opening. Spring: a 1 mm living-hinge arm along the bottom wall returns the gate to closed. Print-in-place: 0.5 mm clearance gaps around the gate and spring, so no assembly is needed. Material: PETG is recommended for the flexing spring arm. Work the gate a few times after printing to free it. Tuning: if the gate sticks or rattles, adjust the clearance for your printer. The spring thickness sets how stiff the gate feels.

1 day agoRemix →

Bharat Key — Mini Number Plate Keychain

Bharat Key is a miniature Indian-style number plate keychain made to carry the exact registration PB 65 BK 3388. The long, slim plate uses a light grey/white base, a thin raised black border, and bold black lettering raised on one horizontal line. The single keyring hole sits at the extreme left with a raised ring around it for strength, while the registration stays centred in the remaining space. No blue IND strip, flag, extra colour or decoration is present, so the tag keeps a clean plate look while staying sturdy enough for a keyring. Dimensions Plate: 75 × 20 × 2.5 mm Raised border and text: 0.6 mm above the base; border 1 mm wide Lettering block: about 57 × 11 mm, fitted to the space right of the hole Keyring hole: 4 mm diameter, cut fully through at the extreme left Hole ring: raised black ring around the hole for extra strength Features Exact registration text: PB 65 BK 3388 on one horizontal line Bold black lettering raised above a light grey/white base Thin raised black border around the whole plate One circular keyring hole at the extreme left, fully through the plate Raised black ring around the hole to reinforce the keyring area Flat rectangular body with slightly rounded corners and a smooth flat backside Light grey/white base and black details only — no blue, no flag, no logos or decorations Print notes Print flat on the back; no supports are needed. The raised border and lettering sit 0.6 mm above the base and read clearly at miniature scale. Keep the 4 mm hole clear so the plate hangs cleanly on a keyring.

3 days agoRemix →