SUPPORT PRINTYTRON
New Model
Loading 3D preview…

Galaxy Cap & Pets

Made by GravelPliers

Created 1 months ago

Kitchen & Bathroompop-topcan-coverskullcollectiblepetsno-supportssnap-fitpetg
Remix this model →

Remixed once

Description

A standalone pop-top can cover designed for easy swapping of customizable 3D-printable pets.

Hooks for Remixing

  • The Peg System: The mounting peg on the cap is a standard 3.8 mm cylinder, sitting slightly toward the back edge. Any custom object with a matching 4.2 mm socket will drop right on.
  • Skull Profile: The flat skull on the cap is an exact scaled-down copy of the original 3D geometry.
  • Expansion: Want to add more utility? You could stretch the cap base horizontally to house three or four pets simultaneously, or angle the peg so the figure faces upward when the can is open.

Images

SUPPORT PRINTYTRON
Tip Jar
Printytron built this for free. If it saved you a trip to the shop, a tip helps keep it free.
Need filament at a great price?
Printing this one? Stock up through our eSun partner link — your price stays the same, but Printytron gets a small commission to go towards our costs.
Brutalist T-Post Cap with Square Platform

Brutalist T-Post Cap with Square Platform

A blocky sleeve that drops over a T-post and carries a flat square platform on top — a brutalist plinth silhouette in cap form, all hard edges and stacked planes. The pocket inside is T-shaped, cut generously around a typical steel fence T-post: a 38 × 7 mm flange opening and a 7 × 38 mm stem slot, leaving roughly a millimetre of play per side so it drops on without a fight. The sleeve is 40 mm deep with 3 mm walls and a 4 mm roof, and the whole cap stands 46 mm tall over a 60 × 60 × 6 mm platform. Design notes T-shaped pocket for a T-post — flange opening 38 × 7 mm, stem slot 7 × 38 mm. Pocket sized with a little slack per side; the 7 mm slot width is the fit-critical dimension on real posts. 40 mm deep sleeve, 3 mm walls, 4 mm roof. 60 × 60 × 6 mm square platform sits on top as one solid piece with the sleeve. Overall footprint on the print plate: 60 × 60 mm, 46 mm tall. Prints as a single part; no assembly and no fasteners. Good to know The pocket is shaped from a typical steel fence T-post rather than a measured one — check your post's flange width, stem length and metal thickness before committing to a long print. Platform size is independent of the pocket, so it can grow or thicken without touching the post fit. Tightening or loosening the pocket is a small change if the cap ends up sloppy or stubborn on the post. The sleeve's outside was widened to 44 mm to keep the walls at a full 3 mm around the bigger pocket, so the cap stays chunky rather than thin-shouldered.

DeftPossum · 14 days agoRemix →
Tiered 12-Jar Spice Rack

Tiered 12-Jar Spice Rack

A three-tier spice rack that holds 12 jars, four per tier, with each tier stepping up so every label stays in view without lifting a jar out. Each pocket is sized for jars about 40 mm across, so the rack is easy to scan for cumin or anything else. The rack measures 180 mm wide, 150 mm deep and 66 mm tall at the back. Tier heights are 26 mm (front), 46 mm (middle) and 66 mm (back). Each tier is 50 mm deep and 20 mm taller than the one in front. Each jar sits in a 42 mm round pocket, 3 mm deep, which stops it sliding forward. The edges carry a 1 mm chamfer. It prints as one piece, and the three tiers are shown in separate colours so they are easy to tell apart. Remix hooks Step height (20 mm): raise it for taller jars behind, or lower it for a shorter rack. Labels stay readable as long as the step is at least as tall as the label band on the jar in front. Tier depth (50 mm): this is set equal to the back-step. Widening both leaves room for larger jars, and a wider step also gives a clearer view of the row behind. Pocket diameter (42 mm) and depth (3 mm): 2 mm of clearance suits 40 mm jars. Increase the diameter for jars that run a little wide. Deepen the pocket for a firmer hold, or set the depth to 0 for a flat shelf. Jars per tier (4, 44 mm pitch): change the count to alter the rack width. Drop to 3 per tier for a narrower footprint, or add a fourth tier for 16 jars. Pairs well with: a non-slip mat underneath, or a rear lip or wall panel to mount it in a cupboard.

Guest · 1 day agoRemix →
Steep-Shouldered Funnel for Clean, Targeted Pouring

Steep-Shouldered Funnel for Clean, Targeted Pouring

A broad-shouldered funnel with a gothic streak: a 100 mm outside rim (84 mm inside) gathers a jug or bottle mouth, the cone narrows into a 26 mm bore, and the stream drops toward the filler. At 82 mm tall it stays compact enough for a tight engine bay, and the inner cone has no side holes, so the pour runs down the middle. The spout is built around a 36.5 mm major-diameter, 3 mm pitch right-hand screw thread that runs the full 10 mm from the tip up to a 40 mm sealing shoulder. The 26 mm bore keeps the pour path open; the thread is the fit feature, so check the filler neck and gasket stack before printing, since the thread has to match the mating part. Four sealed air tunnels, 3 mm across and spaced 90° apart, run inside the wall from the top rim down through the cone. At the lower end each turns inward and opens through the bore wall about 3 mm above the spout tip, so the bottom face stays solid and air can climb while oil runs down the middle. No holes pierce the side of the cone, so it vents without weeping out. The threaded spout wall carries these passages; at the bore openings the material is thin, so inspect the slicer preview before printing. Four raised skulls ring the cone between the tunnels, one every 90°, angled to follow the slope. Each is about 19 mm wide and stands roughly 2.5 mm proud of the surface, with eye sockets, nose and teeth lines cut into the face; the fine teeth lines may print faintly on a 0.4 mm nozzle. They give the funnel a gothic edge without interrupting the flow path. Fit notes 36.5 mm major-diameter, 3 mm pitch right-hand screw thread on the spout Threaded section runs the full 10 mm from the spout tip to the sealing shoulder 40 mm sealing shoulder for a gasket 26 mm bore through the spout Verify thread fit and gasket compression on the filler neck before printing Check the thin tunnel openings near the bore in the slicer preview Design notes 100 mm outside opening, 84 mm inside — a wide catch area 82 mm overall height Four internal 3 mm air tunnels, evenly spaced, opening into the bore about 3 mm above the tip and exiting at the rim Four raised skulls about 19 mm wide and 2.5 mm proud, set between the tunnels Prints as one piece

RafterPrawn · 17 days agoRemix →