Garage Vent to 6-Inch Adapter
Created today
Remixed once
Description
A custom 2-part venting adapter designed to connect a 360x210mm drywall vent gap to a standard 6-inch exhaust duct.
- Two-Part Assembly: Splits perfectly down the middle with a 10mm external flat flange for easy gluing.
- Tapered Male Fitting: Connects securely inside standard 6-inch ducting.
- Support-Free Print: Internal lofts are designed to print cleanly with no supports while encouraging laminar exhaust flow.
- Mounting Integration: Six #6 screw holes for securing to drywall, with an extended bottom footing to rest cleanly on a garage concrete foundation.
Photos
Technical views
More like this
Explore more in Home & Fixtures →
10x10cm Ceiling Vent Air Deflector
A snap-on directional air deflector designed to fit standard 10x10cm ceiling vents. The angled blade redirects downward airflow horizontally across the room, preventing direct drafts over specific areas like workstations and desks. The base attaches directly to the vent housing using integrated flexible geometry. Configured for a 100x100mm outer dimension profile. Integrated flex tabs designed to snap securely over a 5mm thick vent lip. Main deflector blade pitched at a 30-degree angle to sweep cold air laterally. Toolless, print-in-place design requiring no additional mounting hardware.
Geriffelte Pilzkopf-Schraubenkappe
Diese aufschraubbare Kappe verdeckt scharfkantige Holzschrauben, die aus Brettern oder Platten herausragen. Die Form erinnert an einen klassischen Drehknopf und bietet durch die seitlichen Aussparungen sicheren Halt beim Festziehen. Selbstschneidend: Das innere Loch ist konisch geformt (4,2 mm unten, 3,0 mm oben). Das grobe Gewinde der Holzschraube frisst sich beim Aufdrehen von selbst fest. Sicherer Abschluss: Entschärft gefährliche Spitzen und verhindert Kratzer. Druckfertig: Benötigt keine Stützstrukturen, druckt flach auf dem Druckbett.
AquaDart — Garden Hose Nozzle
AquaDart introduces a streamlined approach to targeted water pressure. This single-piece nozzle adapts a standard garden hose down to a precise 0.2-inch exit stream. The internal geometry is specifically contoured to accelerate water smoothly, while the exterior features deep grooves for secure hand-tightening even when wet. Dimensions Overall height: 63 mm Base diameter: 38 mm (at the grip) Exit bore: 5.08 mm (0.2 inches) Interface: Standard 3/4" Female Garden Hose Thread (11.5 TPI) Compatibility & Usage Designed to thread directly onto standard North American garden hoses and spigots. Requires a standard rubber hose washer to sit on the internal ledge. Without the rubber washer, standard garden hose threads will leak under pressure. Print Notes Prints completely completely upright and support-free as oriented. Thick walls (4+ perimeters) and 100% infill are heavily recommended to contain the water pressure and prevent layer separation. PETG or ABS is preferred if this will be left outdoors in the sun.
Under-Shelf LED Routing Corner
A 25mm right-angle block designed to route under-shelf LED strips cleanly around inside corners without kinking. It guides the strip through a 90-degree arc inside a 10.5mm wide, 4mm deep channel, with flat back faces meant for simple adhesive mounting against the shelf walls. Remix Hooks & Constraints Wall Offset: The block's 25x25mm footprint sets the center of the strip exactly 12.5mm from both walls. Changing the block's footprint will let you shift the lighting closer to or further from the front edge of the shelf. Channel Clearance: The 10.5mm width seats a standard bare 10mm LED strip. If you swap to waterproof IP65 strips with heavy silicone doming, this channel needs to be widened to 12.5mm to avoid pinching the arc. Mounting Strategy: The current design relies entirely on flat surfaces for double-sided tape or VHB. An obvious variant for rougher wood shelves is adding a pair of 3mm countersunk holes on the mounting faces.
Aquarium Plant Stem Weight
What it's for This flat, disc-shaped weight anchors live aquarium plants into the substrate. The design features a narrow side-entry slot that leads to a slightly wider central resting hole, allowing stems to be securely trapped without being crushed. It is ideal for newly planted aquascape stems that have not yet developed a stable root system. Dimensions Overall footprint: 25mm in diameter and 8mm thick. Entry slot: 2.5mm wide, running from the edge to the center. Center hole: 4mm diameter clearance to accommodate typical aquatic plant stems safely. Remix ideas Increase the overall thickness to provide more anchoring mass for highly buoyant plants. Widen the entry slot and center hole to accept thicker stem varieties. Change the outer shape from a cylinder to a square or hexagon to pack multiple weights tightly together in dense planting zones.
60mm Projection Coat Hook
A robust wall-mounted coat hook designed with a 60mm projection to accommodate heavy winter coats and standard garments. The geometry features a swept upward arm that terminates in a rounded end to prevent fabric stretching while keeping the item securely suspended. The base plate incorporates two strategically placed countersunk screw holes at a 66mm spacing. The upper hole is positioned to allow clear, unobstructed access for a screwdriver or bit driver during installation. Specifications and print details: 60mm total hook projection Countersunk holes sized for M4 or M5 wood screws 66mm center-to-center hole spacing Print-friendly angles that do not require support structures Smoothly rounded contact points to protect fabrics