Hinged Latching Box With Front Divider
Created today
Description
Small parts slide into one pile as soon as a drawer opens; this hinged latching box stops that with a fixed divider and a lid that snaps shut. The interior is 150 × 125 × 45 mm, split by a 2.5 mm divider set 95 mm back from the front.
Fit and compartments
- Interior: 150 × 125 × 45 mm (length × width × height).
- Divider: 2.5 mm thick, 95 mm back from the front, leaving a larger front bay and a shallower rear bay.
- Walls and floor: 2.5 mm.
- Lid: small inner lip so it locates on the base.
Printing and assembly
- Prints as three separate pieces: base, lid, and hinge pin.
- The pieces are laid out apart on the plate with gaps: the lid is flipped so its flat top face is on the bed, and the 3 mm pin lies flat in the gap. None of the three touch.
- If your slicer imports the model as one body, use Split to objects or Separate parts.
- Hinge: seven interleaved knuckles with a 3 mm pin (153 × 3 × 3 mm). Use a 3 mm rod or filament, or print the pin.
- Front snap latch: hooked tab on the lid over a bump on the front wall. The snap is untested, so expect to tune it.
Images
More like this
Explore more in Storage & Organization →
Mister Box Holder with Open Front
A wall-mounted cradle for a 2.25" x 4.75" x 2" mister box, sized with extra width clearance and a little extra depth so the box slots in easily but can't tip forward out of it. The front is open below a solid top rim so the buttons stay reachable, and a low lip along the bottom front edge holds the box in. Two identical ears on the back face carry countersunk screw holes for mounting to the side of furniture. Full 4.75" (120.65 mm) wall height 10 mm width gap, 3 mm depth gap Cord notch in the left rim only, 15 mm wide, centered 1.5" from the inside back wall, open at the top Window cutouts on the sides to save filament Two back ears with countersunk screw holes
peterson 80x95 v3
sdf
Petersson 95x80 v2
A 95 × 80 mm open-top tray, 50 mm tall, with 2 mm walls and a 2 mm floor. What it has 1.5 mm chamfers on the bottom edges and vertical corners; the top rim stays square. Four triangular corner gussets at the rim (z 47–50 mm), each with a 6.1 mm pocket 2.1 mm deep. A 44 mm long, 45 mm tall cut-out in the centre of the -X wall, leaving a 5 mm bottom lip. 13 vertical grooves (2 mm wide, 0.8 mm deep) on the outside of the +X wall. Check before printing The cut-out is 44 mm long so it stays clear of the gussets. Wider cut-outs would cut into them. Does not fit The earlier 155 mm length is gone; the tray is now 80 mm long.
Apothecary Box With Lift-Off Lid
A classic apothecary-style storage box, 6" x 4" x 2", with a separate lid whose inner lip plugs into the body. The two pieces are laid out side by side for viewing and print as two separate jobs, so each fits an 18 x 18 cm bed. Body: 152.4 x 101.6 x 47.5 mm, 2.4 mm walls, chamfered edges Lid: 152.4 x 101.6 mm, 3 mm plate with a 5 mm plug lip Fit: 0.3 mm clearance between lip and body recess Print the lid flat with the lip facing up, no supports needed
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
Two-Piece Gridfinity Caliper Box
A 6 x 3 unit Gridfinity caliper box split at the middle into two halves, each about 126 x 126 x 25.4 mm, so each fits a 150 mm print bed. Two dovetail keys join the halves. The stepped pocket holds a 9.25 in caliper: a 15.9 mm body slot and a 78 x 97.5 mm head recess, both 12.7 mm deep. The stacking lip and finger scoops are kept. Remix hooks Split position: the cut is at X = 0, on a Gridfinity cell boundary. Moving it in whole 42 mm steps keeps the cells intact. Dovetail size: 8 mm at the root, 13 mm at the tip, 16 mm tall, at Y = ±35. The socket has 0.25 mm clearance. Loosen or tighten it to suit your printer. Joint type: swap the dovetails for round pins or add glue grooves. Pairs with: other Gridfinity bins on a 42 mm baseplate.