Description
A 50 mm dual-sided token featuring bold raised text on the front and flush, mirrored text inlaid on the back. Designed to be printed flat on the bed, using contrasting colours to make the details pop.
- Front: Raised "Round TUIT" text
- Back: Flush-inlaid "3DP@GIRTON.ORG" text
- Dimensions: 50 mm diameter, 3 mm base thickness
Images
More like this
Explore more in Keychains & EDC →
21mm Disk Holder with Snap Lip
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge
Round Turbah Keychain Container
A 40 mm round container with a press-fit lid and a keyring loop, sized for a 35 mm turbah disc. The lid carries a red medallion with a silver ornamental pattern of petals, dots and rings. It has no text. Remix hooks Interior fit: the cavity is 36 mm wide; change ID for a tighter or looser disc. Height: the base is 11 mm and the lid adds 3 mm for a stack of about 14–15 mm; raise the base height for thicker discs. Ornament: petal count (12 at 30° steps), ring diameters and relief height (0.4 mm) are easy to change. Lid grip: the 30 ribs around the rim can be removed or swapped for a knurl. Colours: print black, red and silver as separate colour regions in a multicolour slicer. Pairs with: a split ring or lanyard clip through the 6 mm loop hole.
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
35 mm Threaded Keychain Container, Rosette Lid
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
Pin de mano esquelética con dedo medio levantado
Pin con forma de mano esquelética cerrando el puño y con el dedo medio levantado. El dedo medio sube recto con sus tres falanges; el índice, el anular y el meñique quedan plegados hacia la palma. El pulgar va por detrás de los dedos plegados, así que solo asoma por el lado izquierdo y entre los huesos. Los huesos son blancos y de estilo realista: cada uno tiene una diáfisis fina y dos cóndilos redondeados en cada extremo, con una muesca central, y el extremo superior algo más pequeño. Las divisiones negras entre huesos marcan las articulaciones. En la palma hay cuatro metacarpianos y en la muñeca un grupo de huesos del carpo pequeños. La placa negra de 2 mm sigue la silueta de la mano y sobresale como borde. Los huesos van elevados 0,9 mm sobre ella, con la parte trasera completamente plana. La pieza mide unos 23 × 36 mm, así que queda 1 mm por encima de los 35 mm; el grosor total es de unos 2,9 mm. Para ajustarla al límite de 35 mm, reduce el borde de la placa. Placa negra plana de 2 mm; huesos blancos elevados 0,9 mm Huesos segmentados y separados por huecos negros de articulación, todos apoyados en la placa Sin piezas flotantes; se imprime como una sola pieza Sin soportes: la parte trasera es plana y los detalles se elevan desde la placa Huecos estrechos entre huesos; pensados para una boquilla de 0,4 mm
Portachiavi Famiglia Raganella con rilievo
Il portachiavi a raganella risolve il momento in cui tutte le chiavi di casa sembrano la stessa copia e si finisce a provarle una per una. La rana e la scritta FAMIGLIA RAGANELLA restano in rilievo sulla piastra, mentre le zampe anteriori e posteriori sono state abbassate fino a fondersi con il portachiavi: non restano sospese sopra la piastra e non sporgono come elementi separati. Misure e stampa Set da cinque portachiavi: ingombro 194 × 52 mm sul piano di stampa Piastra singola: 34 × 44 mm, spessore 3 mm Foro per l'anello: 5 mm Rana e scritta in rilievo, circa 1 mm sopra la piastra Zampe anteriori e posteriori fuse alla piastra Stampa piatta, senza supporti, anche in PLA