Description
A slim, hard-shell card wallet designed to hold up to six standard payment or ID cards. The internal pocket is precision-sized to maintain a secure fit, while the bottom of the wallet features a specialized push-out track. Instead of deploying all cards equally, the thumb cutout steps forward, allowing the front-most card to slide out higher than the remaining stack for immediate access.
- Built with an 86.5 x 55 x 6mm internal capacity to fit six standard cards
- Stepped thumb slot isolates and elevates the primary card
- Minimalist exterior profile reduces pocket bulk
Images
More like this
Explore more in Keychains & EDC →
Staircase Slim Card Wallet
A card wallet with the silhouette of a tiny amphitheatre: six standard cards sit in a tall open pocket, and the floor climbs toward the front in 1.5 mm steps so the front card rides highest. A rounded thumb cutout in the front wall lets you push the stack up and out, and the front card pops clear of the rest for a quick grab. The pocket is sized for standard credit cards (85.6 x 54 x 0.76 mm) with a little breathing room, in a slim 90.5 x 10 x 58 mm body. The stepped floor is a separate colour region in the preview so the staircase is easy to read. Design notes Pocket: 86.5 x 55 x 6 mm, open at the top Floor: six steps, each 1.5 mm higher than the one behind, so the front card sits about 7.5 mm above the back one Thumb cutout: round-bottomed notch through the front wall, 36 mm wide Vertical corners rounded at 1.5 mm for a comfortable pocket feel Prints upright or flat; no supports are needed for the main body Remix hooks Taller or shorter steps for a different stagger A narrower thumb notch for a stiffer front wall Fewer steps and a thinner pocket for a 3 or 4 card version
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
Minecraft Grass Block Keychain
What it's for A keychain shaped like a Minecraft grass block: smooth brown dirt body, green grass cap that overhangs slightly, and blunt, irregular grass drips on all four sides. A sturdy corner loop takes a key ring. Dimensions Approx. 27 × 27 × 28 mm Cap about 5 mm thick; drips 3.5–8 mm long Loop hole about 4 mm, at one top corner Remix ideas Swap colours for mycelium or snow blocks Change drip layout Enlarge the loop hole for a lanyard
35 mm Threaded Keychain Container, Rosette Lid
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
Pin de mano esquelética con dedo medio levantado
Pin con forma de mano esquelética cerrando el puño y con el dedo medio levantado. El dedo medio sube recto con sus tres falanges; el índice, el anular y el meñique quedan plegados hacia la palma. El pulgar va por detrás de los dedos plegados, así que solo asoma por el lado izquierdo y entre los huesos. Los huesos son blancos y de estilo realista: cada uno tiene una diáfisis fina y dos cóndilos redondeados en cada extremo, con una muesca central, y el extremo superior algo más pequeño. Las divisiones negras entre huesos marcan las articulaciones. En la palma hay cuatro metacarpianos y en la muñeca un grupo de huesos del carpo pequeños. La placa negra de 2 mm sigue la silueta de la mano y sobresale como borde. Los huesos van elevados 0,9 mm sobre ella, con la parte trasera completamente plana. La pieza mide unos 23 × 36 mm, así que queda 1 mm por encima de los 35 mm; el grosor total es de unos 2,9 mm. Para ajustarla al límite de 35 mm, reduce el borde de la placa. Placa negra plana de 2 mm; huesos blancos elevados 0,9 mm Huesos segmentados y separados por huecos negros de articulación, todos apoyados en la placa Sin piezas flotantes; se imprime como una sola pieza Sin soportes: la parte trasera es plana y los detalles se elevan desde la placa Huecos estrechos entre huesos; pensados para una boquilla de 0,4 mm
21mm Disk Holder with Snap Lip
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge