Stenhus Gymnasium Nøglering
Created yesterday
Description
En robust nøglering med Stenhus Gymnasiums navn sat op i blok-format (hvor linjerne er tvunget til samme bredde), og et dedikeret svunget bølge-symbol i venstre side med vandrette afskæringer i top og bund.
- Mål: Basen er 90 x 30 mm med afrundede hjørner og et forstærket hul til nøgleringen.
- Relief: Både tekst og logo løfter sig diskret 0,6 mm fra basen, hvilket giver et skarpt print uden at det griber for meget fast i lommen.
- Tekst: Ordene er sat med Roboto, hvor bunden er skaleret for at give et balanceret, tungt udtryk.
Images
More like this
Explore more in Keychains & EDC →
Chunky Modern Type Keychain
A solid, pocket-sized keychain featuring a custom typographic design. The base perfectly contours the bold lettering, creating a clean and modern silhouette that feels sturdy in hand. Pocket-Friendly Size: Scaled down to slide easily into a pocket without snagging. Sturdy Build: A solid 5 mm base prevents flexing, with 2 mm raised lettering that holds up to daily wear. Ready to Mount: Features a fully through 5 mm keyring hole to accommodate standard rings or small carabiners.
Embossed Corporate Logo Keychain
A minimalist, single-piece keychain blank featuring raised corporate typography. The body uses a flat-bottomed pill geometry to print seamlessly on an FDM bed without supports, while the integrated mounting hole ensures the outer perimeter remains completely uninterrupted. Print Specifications: Dimensions: 65 mm × 32 mm × 4.2 mm (total height including text). Mounting interface: 5.5 mm diameter integrated hole, positioned for 4 mm of solid wall thickness to resist torsion. Lettering clearance: Text is extruded 1.2 mm above the base layer, providing enough depth for a mid-print filament swap if high-contrast text is desired. Material guidance: Prints cleanly in PETG or PLA. No brim required.
BTS Balm Capsule
A bright pink travel capsule sized for standard lip balm tubes, featuring the BTS door logo repeating across the exterior. The friction-fit cap includes a sturdy heart-shaped loop for attaching to a keychain or lanyard, keeping your balm secure and accessible on the go. Staggered logo pattern wrapping both the sleeve and cap Built-in push hole at the bottom to easily eject the tube Sized with a 16mm inner diameter to prevent rattling
Captive-Pea Emergency Keychain Whistle
A 50mm print-in-place emergency whistle built around a 12mm spherical resonating chamber. It features a tapered mouthpiece and an integrated 7mm captive pea that creates a high-decibel warble, all packed into a low-profile keychain block. Remix Hooks & Constraints Chamber Geometry: The fundamental tone is dictated by the 12mm sphere. Expanding this chamber lowers the pitch, while shrinking it creates a sharper, higher shriek. Captive Pea: The 7mm pea prints with a 0.2mm floor gap. This clearance is just tight enough to prevent the sphere from tearing off the build plate, but weak enough to break free with a pen tip. Windway & Fipple: The air channel is fixed at 1.5mm high to compress the airstream before it hits the 45-degree splitting edge. Changing the fipple angle will dramatically alter the sound quality. Mounting Loop: The 5mm bore at the rear fits standard split rings and 550 paracord. If scaling the model for a heavier carabiner, reinforce the tail block first.
Piaggio Yamaha Demon Keychain
A solid-block Piaggio and Yamaha crossover keychain. The tuning fork emblem takes the center, flanked by sunken demon faces tucked neatly inside the primary shield perimeter. Overall footprint: Scales out to 40mm wide by 60mm tall. Key ring bore: Roughly 4.4mm internal diameter on the revised scale. Fitment note: Verify your split-ring gauge against the bore before committing to the plate. Prints dead flat.
Creality 8-Key Switch Tester Set
An 8-slot mechanical switch tester keychain featuring a rigid frame with standard 14mm square cutouts for mechanical switches. Now includes eight matching keycaps forming the word "creality". Frame: 175mm wide frame with side-engraved "creality" text and a 5.5mm keychain loop. Keycaps: 8 individual keycaps with Cherry MX-compatible cross stems. Assembly: Snap your own switches into the frame slots, then press the printed keycaps onto the stems.