Cactus Pot With Drainage Hole
Created today
Description
A cactus pot with a drainage hole, so water leaves the soil instead of rotting the roots. A separate saucer catches the runoff so it doesn't end up on the windowsill.
Key numbers
- Pot: 70 mm base, 90 mm opening, 75 mm tall, 96 mm rim lip
- Drainage hole: 10 mm diameter, centred in the 6 mm floor
- Saucer: 90 mm diameter, 12 mm tall, 2.5 mm floor. The pot's 70 mm base sits inside it.
- Print: no supports needed, both pieces print upright. 0.2 mm layers, PETG or PLA.
Images
More like this
Explore more in Home & Fixtures →
100x59 Oval Body Hole Cover with Snap Clips
Einsteckbare Abdeckung für eine ovale Öffnung von 100 × 59 mm in etwa 1 mm dickem Blech. Die Frontplatte ist vollständig geschlossen und liegt mit einem 3 mm breiten Auflageflansch rundum auf dem Blech auf; außen misst die Abdeckung 106 × 65 mm bei 2,5 mm Plattendicke. Auf der Rückseite zentriert ein Rahmen mit 2 mm Wandstärke und einer Innenöffnung von 96 × 55 mm als ovales Langloch mit Endradius 27,5 mm. Der Rahmen reicht 7 mm über den Flansch hinaus. Die vier flexiblen Clips – je zwei an den langen Kanten – haben 0,8 mm hohe Haken und angeschrägte Einführflächen; die Rastkante sitzt 7 mm über der Flanschfläche. Mit den verlängerten Federschlitzen baut die Abdeckung insgesamt 13 mm hoch. Bei 1 mm Blech bleibt zwischen Blech und Rastkante in Einsteckrichtung Luft; der Clip rastet erst nach 7 mm Einstecktiefe ein. Werkzeuglose Montage und Demontage Einteiliger Körper, keine Schrauben und kein Kleber Flansch nach unten drucken, in PETG oder ASA Clipsitz beim ersten Druck prüfen, da die Federwirkung des Materials schwankt
Bug Zapper Battery Compartment Cover
Replacement battery compartment cover for a handheld bug zapper, built as a flat plate with a locating lip and a latch tab. Dimensions are estimates and need checking against the original. Plate: 34 x 60 x 2 mm, chamfered edges Inner lip: 30 x 56 x 1.8 mm Latch tab: 10 x 3 x 4.5 mm at one end Grip grooves: four, on the outer face Material: PLA or PETG, printed flat with no supports
83mm Desk Grommet with Sealed Hollow Body
A one-piece desk grommet for an 83 mm hole, with an off-center cable passage. The barrel drops through the desk and the 99 mm flange rests on the surface; 3 mm caps close the part at both ends and the interior is a sealed hollow, so it uses little filament for its size. A 14 mm cable hole sits 30 mm from the center, about 4 mm in from the rim, and passes through the flange and both caps. It takes most round power cables but will not pass a plug. Desk hole: 83 mm Barrel: 82.6 mm outside diameter, 20 mm tall Flange: 99 mm diameter Cable hole: 14 mm diameter, 30 mm from center, near the edge Wall and cap thickness: 3 mm; cable-hole wall: 2 mm Interior: sealed hollow cavity Fit: desk tops up to about 17 mm thick Print: one piece; no external supports; the enclosed cavity will bridge internally near the top of the void Overall footprint on the plate: 99 × 99 × 20 mm
Pay For Photos At Till Sign
A "Please pay for photos at the till" sign for counters and shop windows, where customers walk off with prints without paying. Raised white lettering on a flat blue plate reads clearly from a distance. Print details Plate: 160 × 60 × 8 mm, rounded edges Lettering: two lines, raised 1.2 mm from the front face Print flat on its back; switch filament for the letters, or paint them No supports needed Attach with double-sided tape or foam pads
Vileda Broom Bar Hook
A bare metal broom top snags on everything, and the mushroom-shaped anchor on a Vileda stick gives a plain hook nothing secure to grab. This replacement end cap sleeves 20 mm down over the sharp top of the stick, then snaps over the anchor on four flexing collet fingers with locking pads. The open hook sits centered over the sleeve so the broom hangs straight on a 27 mm bar, and the flared mouth catches the bar without needing perfect alignment. Fit and print Broomstick: fits a 25.3 mm Vileda stick; the sleeve drops 20 mm over the sharp top edge. Anchor: clears the 13 mm mushroom cap and locks around the 10 mm shaft. The four fingers are 3 mm at their weakest point and taper to 4.5 mm at the base, with a 24 mm relief void and 2 mm slits so they splay outward without binding. Hook: open downward U-channel for a 27 mm bar, not a closed loop; the flared mouth funnels the bar in. Wall: solid plastic separates the flex mechanism from the hook cavity, and the hook sits raised clear of the flex chamber. Printing: lay the 2 mm flat plateau on top of the arch on the bed and print upside down — no supports, the internal ceiling bridges. Feel: the thicker fingers take a firmer push to seat, and hold once they do. Size: 31 mm wide, 63.5 mm deep, 118 mm tall as oriented for printing.
White 4 x 10 Inch Flat Vent Grill
Flat slotted vent grill, 10" x 4" with a thickness of 1/4". Two banks of eight through-slots are separated by a center rib for stiffness, inside a solid border. Size: 254 x 101.6 x 6.35 mm Slots: 8 per side, 5 mm wide, 112 mm long, rounded ends Border: about 10 mm solid on the long edges, 15 mm on the ends Print flat, no supports; PETG or ASA suits warm airflow Edges: 4 mm rounded vertical corners