White 4 x 10 Inch Flat Vent Grill
Created today
Description
Flat slotted vent grill, 10" x 4" with a thickness of 1/4". Two banks of eight through-slots are separated by a center rib for stiffness, inside a solid border.
- Size: 254 x 101.6 x 6.35 mm
- Slots: 8 per side, 5 mm wide, 112 mm long, rounded ends
- Border: about 10 mm solid on the long edges, 15 mm on the ends
- Print flat, no supports; PETG or ASA suits warm airflow
- Edges: 4 mm rounded vertical corners
Images
More like this
Explore more in Home & Fixtures →
108 mm Vent Grille Cap, Center-Rib Clearance
Closed 108 mm rounded-square cap for an installed round vent grille (about 99 mm body, 108 mm flange), with a dedicated recess over the raised center rib. Fit Fits over: round grille up to about 100 mm, flange up to about 101.5 mm square. Face: 4 mm, fully closed. Cavity: 100.5 mm round, 15 mm clearance above the grille, plus a 24 mm wide channel along X reaching 21 mm clear. Lip: 10 mm deep, 3 mm walls, 102 mm pocket, eight small friction bumps. Check before printing Measure the center rib's height and direction. The channel assumes it runs along X and stays under about 18 mm tall. Not compatible Flanges over 101.5 mm square or grilles wider than 100 mm.
12V-Stabschiene 6 mm Klemmplatte für Ø80 Spot
Zweiteilige Trägerplatte für einen runden 220V-Spot mit 80 mm Basis auf einem 12V-Stabsystem: zwei parallele Stäbe Ø6 mm, 35 mm Mitte zu Mitte. Die Oberplatte trägt den Spot, die Unterplatte klemmt die Stäbe von unten dagegen. Passt auf Zwei Rundstäbe Ø6 mm, Abstand 35 mm Mitte zu Mitte (Nuten Ø6,3 mm) Runde Spotbasis Ø80 mm (Senkung Ø80,4 mm) Passt nicht auf Stäbe mit anderem Durchmesser oder anderem Abstand Spots mit abweichendem Lochbild: angenommen sind drei Löcher Ø4,5 mm auf Lochkreis 60 mm Vor dem Drucken prüfen Lochbild des Spots und Stabdurchmesser nachmessen. Montage Sechs Schrauben M4 von unten durch die Unterplatte (Senkung für den Kopf) in die Oberplatte; Bohrung Ø3,4 mm schneidet das Gewinde selbst. Kabeldurchlass Ø14 mm in der Mitte. Beide Teile liegen mit offenen Nuten nach oben auf dem Druckbett, ohne Stützen. Ein 220V-Spot an einer 12V-Schiene braucht eine saubere elektrische Trennung. Das Druckteil ersetzt keine Schutzisolierung.
70 × 108 × 25.5 mm Box Snap-Clip Frame
Snap-clip mounting frame for a 70 × 108 × 25.5 mm box, with two 20 mm clips joined by a lightweight frame. Fit Clips sit 108.6 mm apart, inside to inside. Four 20 mm corner blocks locate the box sideways, with 0.3 mm of play per side. Three countersunk screw holes: one in each clip flange and one at the center. Check before printing Confirm the box measures 70 × 108 × 25.5 mm. It does not suit other sizes without changing the clip spacing and block positions. Structure The frame is 3 mm thick. It uses two edge rails, three crossbars and a center screw pad, and prints flat on its back.
Pool Noodle End Cap Plug
A pool noodle end cap that plugs the hole so water, sand and grit stay out of the foam, and the open end stops getting chewed up. The plug uses the same barbed shaft as the noodle connector, so it grips the foam instead of working loose. Key numbers Shaft: 22 mm diameter, 56 mm long, tip chamfered for easy starting Barb rings: four, 28 mm diameter, 14 mm apart, chamfered both sides Head: 70 mm diameter, 8 mm thick, rounded top edge, stops flush against the noodle end Sized for a roughly 25 mm centre hole; foam stretches over the rings Printing Print head-down on the plate, shaft pointing up No supports needed, the ring chamfers handle the overhang PETG or similar; 3 perimeters for stiffer barbs
100x59 Oval Body Hole Cover with Snap Clips
Push-in cover for a 100 x 59 mm oval opening in 1 mm sheet metal. The front plate is fully closed, with a 3 mm overlap flange all round (106 x 65 mm outer, 2.5 mm thick). A 2 mm wall locating frame (99.4 x 58.4 mm, 5 mm deep) centres the cover in the opening. Four flexible cantilever clips (two per long edge) have tapered lead-ins and 0.8 mm hooks that lock behind the sheet metal. Tool-free install and removal Single solid body, no screws or glue Print flange-side down in PETG or ASA
30° Ceiling Vent Air Deflector
A clip-on deflector for a 10 x 10 cm ceiling vent. A blade tilted 30° redirects cold air sideways across the room instead of straight down onto a desk. Four spring tabs grip the vent edges and flex over a 5 mm thick lip. What it's for Redirects airflow from a square ceiling vent away from a desk or seat. Mounts without screws or adhesive: the four tabs snap over the vent lip. The blade spans the opening at a fixed 30° angle. Dimensions Frame: 108 x 108 mm outer, 96 x 96 mm opening, 3 mm thick. Spring tabs: four, one per side, 16 mm wide, with a 5.4 mm gap under the hook for a 5 mm lip. Tabs reach about 10.4 mm above the frame base. Blade: 96 mm wide, 2.4 mm thick, tilted 30°. Overall height is about 22.6 mm. Assumes a 100 x 100 mm vent opening with the frame sitting around it. Print notes PETG is the better choice, since the tabs flex and PLA is more likely to snap. Print the frame flat, with its base on the bed. Check the lip thickness on your vent. Adjust the tab gap if it is not 5 mm. Remix ideas Change the blade angle for a steeper or shallower sweep. Make the tabs wider or thicker for a firmer grip. Resize the frame for a different vent size. Add a second blade to split the airflow in two directions.