Pay For Photos At Till Sign
Created today
Description
A "Please pay for photos at the till" sign for counters and shop windows, where customers walk off with prints without paying. Raised white lettering on a flat blue plate reads clearly from a distance.
Print details
- Plate: 160 × 60 × 8 mm, rounded edges
- Lettering: two lines, raised 1.2 mm from the front face
- Print flat on its back; switch filament for the letters, or paint them
- No supports needed
- Attach with double-sided tape or foam pads
Images
More like this
Explore more in Home & Fixtures →
Cardboard Sign Corner Holder for Wall
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad. Slot height: 3.4 mm for 3 mm cardboard Leg length: 40 mm per corner Back plate: 2 mm, flat side faces the wall Front lip: 1.6 mm, with a cut-out window Print: flat on the back, no supports, one per corner (4 for a sign)
Vileda Broom Bar Hook
A bare metal broom top snags on everything, and the mushroom-shaped anchor on a Vileda stick gives a plain hook nothing secure to grab. This replacement end cap sleeves 20 mm down over the sharp top of the stick, then snaps over the anchor on four flexing collet fingers with locking pads. The open hook sits centered over the sleeve so the broom hangs straight on a 27 mm bar, and the flared mouth catches the bar without needing perfect alignment. Fit and print Broomstick: fits a 25.3 mm Vileda stick; the sleeve drops 20 mm over the sharp top edge. Anchor: clears the 13 mm mushroom cap and locks around the 10 mm shaft. The four fingers are 3 mm at their weakest point and taper to 4.5 mm at the base, with a 24 mm relief void and 2 mm slits so they splay outward without binding. Hook: open downward U-channel for a 27 mm bar, not a closed loop; the flared mouth funnels the bar in. Wall: solid plastic separates the flex mechanism from the hook cavity, and the hook sits raised clear of the flex chamber. Printing: lay the 2 mm flat plateau on top of the arch on the bed and print upside down — no supports, the internal ceiling bridges. Feel: the thicker fingers take a firmer push to seat, and hold once they do. Size: 31 mm wide, 63.5 mm deep, 118 mm tall as oriented for printing.
70mm Desk Hole Cap, Hollow
A hollow, fully closed cap for a 70 mm desk hole. A 69.6 mm barrel fits the hole and an 86 mm flange sits on the desk surface. Both ends are closed with 3 mm caps, and the interior is left empty to save filament. Barrel: 69.6 mm diameter, 20 mm tall Flange: 86 mm diameter, 3 mm thick, chamfered edge Caps: 3 mm solid at both ends Interior: sealed hollow, 63.6 mm diameter Print with the flange side down; no supports needed
White 4 x 10 Inch Flat Vent Grill
Flat slotted vent grill, 10" x 4" with a thickness of 1/4". Two banks of eight through-slots are separated by a center rib for stiffness, inside a solid border. Size: 254 x 101.6 x 6.35 mm Slots: 8 per side, 5 mm wide, 112 mm long, rounded ends Border: about 10 mm solid on the long edges, 15 mm on the ends Print flat, no supports; PETG or ASA suits warm airflow Edges: 4 mm rounded vertical corners
12V-Stabschiene 6 mm Klemmplatte für Ø80 Spot
Zweiteilige Trägerplatte für einen runden 220V-Spot mit 80 mm Basis auf einem 12V-Stabsystem: zwei parallele Stäbe Ø6 mm, 35 mm Mitte zu Mitte. Die Oberplatte trägt den Spot, die Unterplatte klemmt die Stäbe von unten dagegen. Passt auf Zwei Rundstäbe Ø6 mm, Abstand 35 mm Mitte zu Mitte (Nuten Ø6,3 mm) Runde Spotbasis Ø80 mm (Senkung Ø80,4 mm) Passt nicht auf Stäbe mit anderem Durchmesser oder anderem Abstand Spots mit abweichendem Lochbild: angenommen sind drei Löcher Ø4,5 mm auf Lochkreis 60 mm Vor dem Drucken prüfen Lochbild des Spots und Stabdurchmesser nachmessen. Montage Sechs Schrauben M4 von unten durch die Unterplatte (Senkung für den Kopf) in die Oberplatte; Bohrung Ø3,4 mm schneidet das Gewinde selbst. Kabeldurchlass Ø14 mm in der Mitte. Beide Teile liegen mit offenen Nuten nach oben auf dem Druckbett, ohne Stützen. Ein 220V-Spot an einer 12V-Schiene braucht eine saubere elektrische Trennung. Das Druckteil ersetzt keine Schutzisolierung.
70 × 108 × 25.5 mm Box Snap-Clip Frame
Snap-clip mounting frame for a 70 × 108 × 25.5 mm box, with two 20 mm clips joined by a lightweight frame. Fit Clips sit 108.6 mm apart, inside to inside. Four 20 mm corner blocks locate the box sideways, with 0.3 mm of play per side. Three countersunk screw holes: one in each clip flange and one at the center. Check before printing Confirm the box measures 70 × 108 × 25.5 mm. It does not suit other sizes without changing the clip spacing and block positions. Structure The frame is 3 mm thick. It uses two edge rails, three crossbars and a center screw pad, and prints flat on its back.