Finger Trunking with Snap-On Lid
Created today
Description
Finger trunking that blocks access to your mounting holes is a problem. This one has floor slots cut where the screws and the access hole need to be, plus a snap-on lid.
The walls are free-standing fingers with barbs at the tips. The lid's inward lip clips under the barbs.
- Size: 340 × 30 × 35 mm, with 2 mm walls and a 2 mm floor.
- Fingers: 4 mm gaps on a 10 mm pitch.
- M3 slots: Four slots, 3.4 mm wide and 5.4 mm long. They sit at 10, 100.75, 191.5 and 282.25 mm from the left end, 90.75 mm apart.
- Access hole: 7 mm diameter, 201.5 mm from the left end.
- Slot line: All slots sit 10.786 mm toward +Y from the centreline.
- Printing: The trunking is longer than most print beds. Print it diagonally or split it. The lid lip is a small overhang when printed flat.
Images
More like this
Explore more in Home & Fixtures →
100x59 Oval Body Hole Cover with Snap Clips
Einsteckbare Abdeckung für eine ovale Öffnung von 100 × 59 mm in etwa 1 mm dickem Blech. Die Frontplatte ist vollständig geschlossen und liegt mit einem 3 mm breiten Auflageflansch rundum auf dem Blech auf; außen misst die Abdeckung 106 × 65 mm bei 2,5 mm Plattendicke. Auf der Rückseite zentriert ein Rahmen mit 2 mm Wandstärke und einer Innenöffnung von 96 × 55 mm als ovales Langloch mit Endradius 27,5 mm. Der Rahmen reicht 7 mm über den Flansch hinaus. Die vier flexiblen Clips – je zwei an den langen Kanten – haben 0,8 mm hohe Haken und angeschrägte Einführflächen; die Rastkante sitzt 7 mm über der Flanschfläche. Mit den verlängerten Federschlitzen baut die Abdeckung insgesamt 13 mm hoch. Bei 1 mm Blech bleibt zwischen Blech und Rastkante in Einsteckrichtung Luft; der Clip rastet erst nach 7 mm Einstecktiefe ein. Werkzeuglose Montage und Demontage Einteiliger Körper, keine Schrauben und kein Kleber Flansch nach unten drucken, in PETG oder ASA Clipsitz beim ersten Druck prüfen, da die Federwirkung des Materials schwankt
70 × 108 × 25.5 mm Box Snap-Clip Frame
Snap-clip mounting frame for a 70 × 108 × 25.5 mm box, with two 20 mm clips joined by a lightweight frame. Fit Clips sit 108.6 mm apart, inside to inside. Four 20 mm corner blocks locate the box sideways, with 0.3 mm of play per side. Three countersunk screw holes: one in each clip flange and one at the center. Check before printing Confirm the box measures 70 × 108 × 25.5 mm. It does not suit other sizes without changing the clip spacing and block positions. Structure The frame is 3 mm thick. It uses two edge rails, three crossbars and a center screw pad, and prints flat on its back.
Bug Zapper Battery Cover 27.65 x 60 mm
Sliding battery compartment cover plate for a bug zapper, 27.65 mm wide (X) by 60 mm long (Y), with a locating lip underneath, a latch tab at one end and grip grooves on the outer face. Dimensions are estimates and should be checked against the original cover before printing. Plate: 27.65 x 60 x 2 mm, chamfered edge Locating lip: 23.65 x 56 x 1.8 mm Latch tab: 10 mm wide, 4.5 mm tall overall Grip grooves: four, 18 mm long Material: PLA or PETG, printed flat
Anglewright — 90° L Profile
Anglewright is a clean 90° L profile with unequal legs: 2 in along one axis and 1.2 in along the other, standing 2 in tall. Both legs are 0.5 in thick, giving a simple right-angle section for corner bracing, spacing, or building up a frame. The form is a single continuous L, so the shape itself carries the function. Dimensions Overall height: 2 in (50.8 mm) Leg lengths: 2 in × 1.2 in (50.8 mm × 30.5 mm) Leg thickness: 0.5 in Corner angle: 90° Print notes At 2 in tall the profile sits comfortably within a typical print bed, so it can be printed standing up on its end with no special base. Lying on its side also works and keeps the flat L section stable on the plate. No supports are needed either way; the 0.5 in legs give plenty of contact area. Features Single-piece right-angle profile with no assembly Unequal legs for mixing offsets in two directions Small enough to print several at once for a set of matched braces
Cactus Pot With Drainage Hole
A cactus pot with a drainage hole, so water leaves the soil instead of rotting the roots. A separate saucer catches the runoff so it doesn't end up on the windowsill. Key numbers Pot: 70 mm base, 90 mm opening, 75 mm tall, 96 mm rim lip Drainage hole: 10 mm diameter, centred in the 6 mm floor Saucer: 90 mm diameter, 12 mm tall, 2.5 mm floor. The pot's 70 mm base sits inside it. Print: no supports needed, both pieces print upright. 0.2 mm layers, PETG or PLA.
