Made by PeterF
Created 1 months ago
Description
A 4mm scale (OO gauge) wooden side gate, complete with an outer frame. Features standard vertical planking on the front, Z-bracing on the back, and basic hinge and latch hardware.
Images

A flat-pack 4mm/OO scale Georgian townhouse half-relief facade. Features separate drop-in windows and a six-panel door with an ornate canopy hood, plus 45-degree mitered side walls for a seamless glued corner finish. What it's for Designed for model railway backdrops and dioramas, this building prints flat to minimise print time and eliminate the need for supports. The individual pre-coloured inserts allow you to paint the facade and glazing separately before dropping them into place. Dimensions Scale: 1:76 (OO Gauge) Assembled Footprint: 76 mm wide × 18 mm deep Facade Height: 130 mm (Three storeys) Print notes Supports: None required. The canopy and all window frames are designed to print vertically from the build plate. Fitment: The window and door cutouts are oversized by 0.5 mm for an easy drop-in fit. Use standard plastic cement or superglue on the rear locator blocks.
A half-relief take on a Victorian terraced house in OO gauge: brick front with quoins, mitred corners and a roof that pitches back at 45° from the eaves, like the shop-front buildings that sit flat against a layout backscene. The side walls rise in a 45° slope to meet the roof, and the two tiled roof panels are sized to overhang the front and both sides. Brick front with separate window and door inserts Two mirrored side walls, 15 mm deep, with sloped tops Floor piece spanning between the sides Two tile-pattern roof panels, 36 × 25 mm each 45° mitred corner joins
A semi-detached OO gauge house pair with stone walls, a one-piece roof, separate door and window inserts, and chimneys supplied as flat-pack panels. The two 72 mm frontages sit side by side (144 mm overall) with quoins only at the outer ends. Each chimney is four panels plus a capped top, printed flat and joined by a thin 0.4 mm web. A second web holds the windows and door together on the plate. Remix hooks Chimney slope: side panels run 9 to 18 mm high at 45°. Change the two heights to suit a different roof pitch. Panel thickness: 1.5 mm. Thicker panels give stronger glue joints. Web: 0.4 mm tall with 1.2 mm bars. Cut it away after printing, or thin it further. Pairs with: the L-shaped corner brackets (10 × 10 mm legs, 15 mm long) for gluing the walls square.
What it's for A small straight-cut involute spur gear for miniature gear trains, hobby motors and small mechanisms. It is a single solid body with a bore that passes fully through. Dimensions Teeth: 10 Module: 0.5 mm (pitch diameter 5 mm) Outside diameter: 6 mm Pressure angle: 20° Bore: 2.5 mm, through Face width: 5 mm Remix ideas Pair it with a larger module 0.5 gear for a reduction stage. Add a set-screw hub for a motor shaft. Swap the round bore for a D-shaped one.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
A single-arm servo horn for the SG90 micro servo, with a 3.2 mm linkage hole 12 mm from the output shaft centre. Fitment Fits: SG90 and compatible 9 g servos with the 21-tooth, ~4.8 mm output spline. Does not fit: MG90S metal-gear servos with a different spline count, or 25T servos such as MG995/MG996. Arm: 12 mm centre distance, 4 mm thick, rounded edges. Check before printing Test the spline bore on a scrap print. Bore size is ~4.9 mm with small tooth notches, and printer tolerance varies. Adjust it if the fit is loose or tight. The part prints flat with no supports, and PLA works.