Pioneer-Era Wright Flyer Biplane Model
Created today
Description
A detailed tribute to the 1903 Wright Flyer, the fragile-looking biplane that first took powered flight. Two ribbed wings span about 123 mm, held apart by open strut bays, with a double-surface front elevator on booms ahead, twin rudders behind, and long skids beneath. An engine, a prone pilot, and two pusher propellers complete the machine.
Design notes
- Ribbed upper and lower wings with open strut bays.
- Front elevator mounted on booms; twin rudders at the tail.
- Prone pilot lying on the lower wing, matching the Flyer’s flight position.
- Two pusher propellers shown as simplified flat blades.
- Chain drive and wing-warping wires are omitted.
- Grouped as Wings, Wood Frame, Engine, Pilot and Propellers.
Photos
Technical views
More like this
Explore more in Decor & Display →
Male SandWing Dragon with Spread Wings
A standing four-legged male SandWing dragon with two fully spread wings, a continuous sail along the head, neck and spine, and a curved stinger at the tail end. A gold hoop earring passes through the left ear. Colors: sandy-gold body, cream underside, ivory horns and claws, black eyes Wings: continuous membranes on finger-like supports Tail: tapers directly into the curved stinger Base: low flat plate under all four feet
Small City Model with Park and Trees
A 230 × 170 mm town plate laid out as a small city: a row of five tall buildings along the back, a main road with crosswalk, side buildings, houses, cars, streetlights and a park with a pond, crossing paths, a bench, people and many trees. All lettering has been removed. Base: 230 × 170 × 4 mm plate Park: lawn, pond, two crossing paths, 19 trees, bench City: buildings 14–34 mm tall with windows and doors Extras: streetlights, cars, people, crosswalk Print: no supports needed for most parts; trees are cones and print best with a slow top layer
wigwam
Scale model of a wigwam-style domed hut on an 88 mm round base, with an arched front doorway, a top smoke hole, three binding bands and hay thatch strands angled down the dome. Fit and dimensions Base disc: 88 mm diameter, 2 mm thick Dome: about 80 mm wide, roughly 32 mm tall overall Doorway faces -Y; thatch is left clear of it Check before printing Hay strands are about 1 mm thick. Use a 0.4 mm nozzle and expect fine, fragile detail. Not a functional enclosure, and not scaled to fit any figure or miniature line.
model saat
A slim protective sleeve for the SIBIONICS SiWatch with its own reinforced strap lugs, so strap load bypasses the broken originals. The screen, back sensors and charging contacts stay open, and two separate button openings sit on one side edge. Remix hooks button1offset / button2offset: Y position of each opening along the side, measured from the watch centre. Starting values are -5 mm and +5 mm. Each moves independently. btnz, btnlen, btn_h: opening height above the back (5.5 mm), length (6 mm) and height (3.5 mm). btn_side: 1 for the +X edge, -1 for -X. Cavity: watchw 38, watchl 44, watchh 11 and cornerr 9 mm are placeholders to measure. Strap: strapw 22, bard 3, barz 6.5 and bary 1.5 mm. Pairs well with a test-fit print in cheap filament before the final one.
Funfair Swing Ride with Crank, 100 mm Base
Funfair swing ride with a hand crank on top. Turning the crank spins the canopy and seat ring around a fixed central pin, and each of the six seats hangs from a captive ball joint so it swings outward as the ride turns. Base: 100 x 100 x 6 mm plate with a 30 mm column and 14 mm mast Spinning top: 70 mm seat ring and cone canopy on a 8 mm pin, 0.3 mm bearing clearance Seats: six, each on a 7 mm captive ball with a 3 mm rod, printed in place Crank: 30 mm arm with a 7 mm handle on top of the canopy Print in place, no supports needed for the base; the ring cavities bridge over the balls Overall height about 112 mm
OO Scale Arched Door Frame 13x26mm
Arched door frame and separate door for an OO scale (1:76) house, sized for a 13 x 26 mm wall opening with a semicircular top. The frame is 2 mm deep and continues around the inside of the arch, leaving a semicircular glass gap above the door. Frame: 12.8 mm wide, 25.9 mm tall, 2 mm deep Glass gap: semicircle, 8.8 mm across Door: 8.4 x 17.8 mm, printed as a separate piece Door detail: four raised panels, round handle, letterbox plate Fit: 0.1 mm clearance per side in the wall opening Print with a fine layer height; panel relief is 0.4 mm