Ribbed Bathroom Pot
Created 1 months ago
Description
Tall, top-heavy bathroom items have a habit of tipping over or leaving residue on the counter. This ribbed pot is built with thick walls to stay put, corralling toothbrushes, razors, or makeup brushes so they stop sliding around.
Fit & Print
- Outer diameter: 80 mm
- Height: 100 mm
- Internal diameter: 72 mm
- Features: The inside base has a 4mm fillet (a smooth curved transition) instead of a sharp corner, so toothpaste or dust can't get permanently stuck in the bottom rim.
- Printing: Prints straight on the bed. No supports required.
Images
More like this
Explore more in Kitchen & Bathroom →
Funnel 6 to 2.5 Inch
A one-piece funnel with a 6 in (152.4 mm) inner diameter at the wide end, tapering to a 2.5 in (63.5 mm) inner diameter spout. Each end has a 1 in (25.4 mm) straight wall. Remix hooks Taper length: 60 mm cone section. Lengthen for a gentler slope, shorten for a squat funnel. Wall thickness: 2 mm. Raise to 3 mm for rigidity with heavy contents. Spout diameter: 63.5 mm inner. Change it to match a specific container neck. Pairs with: a mesh strainer disc sitting in the 1 in top collar, or a rubber gasket on the spout. Variants: add a rim lip or hanging tab.
Brutalist T-Post Cap with Square Platform
A blocky sleeve that drops over a T-post and carries a flat square platform on top — a brutalist plinth silhouette in cap form, all hard edges and stacked planes. The pocket inside is T-shaped, cut generously around a typical steel fence T-post: a 38 × 7 mm flange opening and a 7 × 38 mm stem slot, leaving roughly a millimetre of play per side so it drops on without a fight. The sleeve is 40 mm deep with 3 mm walls and a 4 mm roof, and the whole cap stands 46 mm tall over a 60 × 60 × 6 mm platform. Design notes T-shaped pocket for a T-post — flange opening 38 × 7 mm, stem slot 7 × 38 mm. Pocket sized with a little slack per side; the 7 mm slot width is the fit-critical dimension on real posts. 40 mm deep sleeve, 3 mm walls, 4 mm roof. 60 × 60 × 6 mm square platform sits on top as one solid piece with the sleeve. Overall footprint on the print plate: 60 × 60 mm, 46 mm tall. Prints as a single part; no assembly and no fasteners. Good to know The pocket is shaped from a typical steel fence T-post rather than a measured one — check your post's flange width, stem length and metal thickness before committing to a long print. Platform size is independent of the pocket, so it can grow or thicken without touching the post fit. Tightening or loosening the pocket is a small change if the cap ends up sloppy or stubborn on the post. The sleeve's outside was widened to 44 mm to keep the walls at a full 3 mm around the bigger pocket, so the cap stays chunky rather than thin-shouldered.
Ribbed Milk Bottle Cap (3 start thread) with Tube Adapter
A low-profile screw cap for a 2L milk bottle, paired with a separate tube adapter that passes through the cap from the inside. The cap has a 3-start internal thread sized for a 37.4 mm bottle thread, a 16 mm hole through the lid, and 24 vertical grip ribs around the outside for easier tightening. The adapter has a 4 mm flange that stops it pulling through the lid, and a tube that tapers from 15.9 mm to 14 mm. Cap: 44 mm body, 13 mm tall, 3 mm lid, 16 mm centre hole Thread: 39.4 mm major diameter, 3.2 mm pitch, 3 starts Adapter: 30 mm overall, 24 mm flange, 10 mm bore Print the cap lid-down and the adapter flange-down
5-Point Star Cookie Cutter
A five-point star cookie cutter, 60 mm tip to tip, with 18 mm tall walls and a wide flat flange around the top edge. The flange gives a thumb a broad surface to press on, so pushing the cutter through dough doesn't put a thin edge against your skin. Remix hooks The values below are the ones worth changing. Everything else follows from them. Star size (R, 30 mm): This is the tip radius, so 60 mm across. Change it to scale the star. At about 40 mm across or less, check that the flange doesn't crowd the inner corners. Point sharpness (ratio, 0.5): This is the inner radius divided by the outer radius. Lower values like 0.4 give spikier points. Higher values like 0.6 give a chubbier, more rounded star. Very spiky points are harder to press out of dough. Flange (flangew 4 mm, flanget 2 mm): Widen it for a more comfortable press, or thicken it for more stiffness. Rounding the flange's outer corners is an easy variant if you want it softer on the thumb. Wall (wall, 1.2 mm): This is about three nozzle widths on a 0.4 mm nozzle. Thinner cuts more cleanly but is more fragile. Thicker is sturdier but pushes dough aside more. Height (H, 18 mm): Lower it for thin cookies, or raise it for thick dough or a deeper grip. Pairs well with A set of different sizes, made by changing R and nothing else. Other shapes that reuse the same wall and flange values, such as a heart or circle, so the whole set feels the same in the hand. A matching stamp or embossing plate that fits inside the cutter opening. Printing Print it flange-up or flange-down on the bed. Flange-down needs no supports, and the thin walls grow straight up from the flange. Use food-safe filament if you want to use it on dough.
65° Kitchen Counter iPad Stand
A wide, flat iPad stand for kitchen counters. The cradle sits at 65° from horizontal, a steep reading angle for recipes while standing. The underside of the base has a shallow recess that leaves a perimeter rim, so the edge seals against the counter and crumbs and flour are less likely to creep under. What it's for Reading recipes on an iPad at standing height without bending over. Use on a kitchen counter, where the wide base resists tipping. The stopper at the bottom of the cradle holds the iPad's lower edge, and the two side tabs keep it from sliding sideways. Dimensions Base: 240 × 170 × 5 mm, with 1.5 mm chamfered edges. Underside recess: 228 × 158 mm, 1.6 mm deep, leaving a rim around the perimeter. Cradle plate: 200 × 150 × 5 mm, tilted at 65° from horizontal. Bottom stopper: 8 mm deep and 11 mm tall, measured from the plate. Side tabs: 6 mm wide, 40 mm long and 16 mm tall, one on each side. Supports: five ribs, each 6 mm thick, spaced 45 mm apart under the cradle. Overall height: about 143 mm. Print notes Print the base face-down on the bed. The underside recess then faces up and needs no supports. PETG or ASA suits a kitchen better than PLA, which softens in heat. The cradle prints as one piece with the base and ribs, so no assembly is needed. Remix ideas Add a raised lip on top of the base to catch spills. Change the tilt angle for a lower or steeper view. Narrow the cradle and tabs for a smaller tablet. Add a cable slot in the stopper for charging while reading. Stick a thin rubber or silicone pad inside the rim for extra grip.
Softflow — M22 Faucet Splash Diffuser
Softflow is a screw-on splash diffuser for faucets with an M22x1 male outlet thread. The base is perforated with a staggered hex grid of small holes, breaking the flow into many fine streams for a softer, wider spray. A short open chamber between the thread and the perforated floor lets water spread across the whole hole pattern before it exits. Features M22x1 female thread, 8 mm deep, with a beveled lead-in at the opening Staggered hex grid of 1.5 mm holes at 2.6 mm spacing, inside an 18 mm circle 3 mm perforated floor with a relief chamber above it Chamfered top and bottom edges on a round body Dimensions Outer diameter: 28 mm Overall height: 16 mm Thread: M22 x 1 mm pitch, 8 mm engagement depth Floor thickness: 3 mm Print notes Print with the perforated face down on the bed, opening facing up; no supports are needed. Thread fit has not been tested against a real faucet. If it binds, increase the thread clearance slightly. A fine layer height (0.12–0.16 mm) keeps the small holes and thread crisp. PETG or ASA suits wet, warm-water use better than PLA.