Round Button With Raised Rim
Created today
Description
A flat round button with a raised, rounded outer rim and four holes at the centre, so thread or a finger doesn't slide off the edge.
Key numbers
- Diameter: 50 mm
- Face thickness: 3 mm, rim peaks at 5 mm
- Rim: 5 mm round bead around the edge
- Holes: four 4 mm holes in a 12 mm square pattern
- Print: flat side down, no supports, 0.2 mm layers
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Raised-Text Visitor Pass 110x70 mm
A 110 × 70 mm single-piece visitor pass for Himalaya Public Sr. Sec. School, with a 2 mm base plate and bold text raised 0.8 mm above it. The three centred lines read HIMALAYA PUBLIC, SR. SEC. SCHOOL and VISITOR PASS. Plate: 110 × 70 mm, 2 mm thick, rounded corners, flat bottom Text: 0.8 mm raised, fused to the plate Total thickness: 2.8 mm Single colour, no supports needed Text size unchanged from the previous version
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament
Women's Sunglasses Frame with Folding Arms
Printed sunglasses where the parts crowd each other on the plate and fuse: this set lays the frame, two folding arms, ribbon inserts and hinge pins out with clear space between them. Frame width: 145 mm, 50 mm tall, 5 mm plate, hinge ears 18.5 mm high Lens openings: 50 × 36 mm each, 16 mm bridge gap Arms: about 139 mm long, 8 mm wide, 6 mm thick, with at least 4.8 mm between each part on the plate Hinge pins: four, 2 mm across, in 2.4 mm holes Hearts and breast cancer awareness ribbons recessed 1 mm on the frame and arms Print flat, no supports needed for the arms
Platte mit Schrift
What it's for Kleine Beschriftungsplatte mit erhabenem Schriftzug HENKIES und zwei Befestigungslöchern, z. B. als Namensschild oder Anhänger. Dimensions Platte: 70 × 18 × 1 mm Löcher: 2 × Ø 4 mm, 55 mm Abstand (Mitte zu Mitte), mittig auf der langen Achse Schrift: HENKIES, 0,7 mm erhaben, mittig, Gesamthöhe 1,7 mm Schriftart: Liberation Sans (Arial-kompatibel) Remix ideas Ecken abrunden Größere Schrift oder andere Schriftart Zusätzliche Fase an den Plattenkanten
Pickleball Paddle Name Stamp with Handle
Custom ink stamp showing a tilted pickleball paddle with a perforated pickleball in the head and the name "Pat" centered below. The design is mirrored so it prints correctly when stamped, and a flared grip handle sits on the back of the plate. Plate: 62 × 86 mm base, 4 mm thick, rounded corners Relief: 2 mm raised design, paddle tilted 35° Ball: 17 mm diameter with 19 holes (1 center, 6 inner ring, 12 outer ring) Handle: 22 × 38 mm stem with 34 × 44 mm cap, about 36 mm overall height Print orientation: design face down on the bed, no supports needed
Print-in-Place Articulated Dragon Fidget Toy
Articulated dragon with a horned head, ten hinged body segments and back spikes. It prints as one piece with no assembly, and the body flexes in a wave when held. Joints: pin hinges with 0.4 mm clearance per side, alternating between side-to-side and up-down bending Segments: 10, tapering from an 18 mm wide head to a narrow tail Size: about 155 mm long, 12 mm tall without spikes Print: lay flat, no supports intended for the body; 0.2 mm layers, PLA or PETG After printing: bend each joint back and forth to break the hinges free Use: desk fidget, sensory toy