Made by a Guest
Created 1 months ago
Description
Standard rectangular tag drilled for a 5 mm split-ring.
Dimensions to check:
Does not include chamfers for sliding into tight leather key wallets. Matches Simao.
Images
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge
Bharat Key is a miniature Indian-style number plate keychain made to carry the exact registration PB 12 V 6821. The long, slim plate pairs a light grey/white base with a thin raised black border and bold black lettering raised on a single horizontal line. The keyring hole sits at the extreme left, ringed with raised black for strength, while the registration stays centred in the space that remains. No blue IND strip, flag, extra colour or decoration is present, so the tag keeps a clean number-plate look while staying sturdy enough for a keyring. Dimensions Plate: 75 × 20 × 2.5 mm Raised border and text: 0.6 mm above the base; border 1 mm wide Keyring hole: 4 mm diameter, cut fully through at the extreme left Hole ring: raised black ring around the hole for extra strength Features Exact registration text: PB 12 V 6821 on one horizontal line Bold black lettering raised above a light grey/white base Thin raised black border around the whole plate One circular keyring hole at the extreme left, fully through the plate Raised black ring around the hole to reinforce the keyring area Flat rectangular body with slightly rounded corners and a smooth flat backside Light grey/white base and black details only — no blue, no flag, no logos or decorations Print notes Print flat on the back; no supports are needed. The raised border and lettering sit 0.6 mm above the base and read clearly at miniature scale. Keep the 4 mm hole clear so the plate hangs cleanly on a keyring.
Chaveiro em formato de esfera de 30 mm com argola no topo e dois pontos amarelos de 5 mm embutidos na face frontal. Esfera: 30 mm de diâmetro Argola: 11 mm externo, 6 mm furo, 2,4 mm de espessura Pontos amarelos: 5 mm, embutidos 0,6 mm abaixo da superfície Impressão em duas cores (preto e amarelo)
A two-piece luggage tag that holds a standard business card and hides the address behind a sliding cover panel. The body is 96 × 66 mm with an 86 × 56 mm card window (a 5 mm border on every side) and a side tab with a 6 mm strap hole. The cover prints flat beside the body and slides in from the right end through grooves in the border. Remix hooks Card window (86 × 56 mm): sized for an 85 × 55 mm card with 0.5 mm play per side. Change both numbers together for other card sizes, and adjust the body size to keep the border. Border width (5 mm): the body is window size plus 10 mm per axis. A wider border gives more room for the grooves and a sturdier tag. Groove clearance: the groove has 0.8 mm of side play and 0.2 mm of height play around the cover. Tighten or loosen these to suit your printer, since this is the fit most likely to need tuning. Detent bump: the cover can slide open on its own, and the card drops in from the top, so it is the only thing keeping the card in. A small bump on the cover and a matching dimple in the groove would hold it shut. Strap tab: 22 × 30 mm and 2.6 mm thick, with a 6 mm hole. Enlarge the hole for wider straps or cable loops. Body thickness: 4.6 mm overall. Thinning it saves filament but shortens the groove and window walls. Pairs well with Split-ring or lanyard clip through the strap hole A different colour for the cover, so the sliding piece reads at a glance Embossed or engraved text on the cover top, such as a name or a "contact owner" line Print notes Print both pieces flat, as laid out on the plate. Check the cover fit after the first print before committing to a batch.
Sei portachiavi con una raganella in rilievo e la scritta FAMIGLIA RAGANELLA, per distinguere le chiavi di casa senza provare tutte le copie. I sei pezzi sono disposti su due file da 3, con 40 mm tra un portachiavi e l'altro lungo X e 56 mm tra le file in Y: si stampano tutti insieme su un'unica piastra, pronti da separare e da agganciare agli anelli. La disposizione resta compatta e tra una piastra e l'anello della fila successiva rimangono pochi millimetri. Le zampe della raganella, davanti e dietro, sono abbassate fino a toccare la piastra del portachiavi, così non restano sospese. Misure e stampa Sei portachiavi in due file da 3 Passo di 40 mm in X, 56 mm tra le file in Y Ingombro totale sul piatto: 114 × 108 × 11,4 mm Piastra singola: 34 × 44 mm, spessore 3 mm Foro per l'anello: 5 mm Corpo della raganella e scritta in rilievo, circa 1 mm sopra la piastra; zampe a contatto con la piastra Stampa piatta, senza supporti, anche in PLA Note Lo spazio tra le file è stretto: se serve più margine attorno ai pezzi, si possono distanziare o stampare in due passaggi.