Swivel Quran Stand
Created today
Description
A rehal-style book stand with a turntable base and two backward-leaning panels, pierced with eight-pointed khatam stars. The stars cut filament use while leaving a solid perimeter frame. A narrow gap between the panels takes the book's spine, and a rounded lip along the bottom edge holds the pages.
- Base: 214 mm disc with a coarse threaded pivot post and low bearing rings.
- Swivel carriage: spins 360° on the post. Two angled slot blocks are printed into it, with no supports needed.
- Retaining cap: screws onto the post to lock the carriage on, no metal or glue.
- Panels: two mirrored panels, 150 × 215 mm, with a flat tongue that slides into each carriage slot.
- Designed around a 170 × 240 mm book of about 1.5 kg, on a 220 mm bed with a 0.4 mm nozzle.
- Panels print flat on their backs. Flip the cap so its top is on the bed.
Images
More like this
Explore more in Home & Fixtures →
Finger Trunking with Snap-On Lid
Finger trunking that blocks access to your mounting holes is a problem. This one has floor slots cut where the screws and the access hole need to be, plus a snap-on lid. The walls are free-standing fingers with barbs at the tips. The lid's inward lip clips under the barbs. Size: 340 × 30 × 35 mm, with 2 mm walls and a 2 mm floor. Fingers: 4 mm gaps on a 10 mm pitch. M3 slots: Four slots, 3.4 mm wide and 5.4 mm long. They sit at 10, 100.75, 191.5 and 282.25 mm from the left end, 90.75 mm apart. Access hole: 7 mm diameter, 201.5 mm from the left end. Slot line: All slots sit 10.786 mm toward +Y from the centreline. Printing: The trunking is longer than most print beds. Print it diagonally or split it. The lid lip is a small overhang when printed flat.
Bug Zapper Battery Cover 27.65 x 60 mm
Sliding battery compartment cover plate for a bug zapper, 27.65 mm wide (X) by 60 mm long (Y), with a locating lip underneath, a latch tab at one end and grip grooves on the outer face. Dimensions are estimates and should be checked against the original cover before printing. Plate: 27.65 x 60 x 2 mm, chamfered edge Locating lip: 23.65 x 56 x 1.8 mm Latch tab: 10 mm wide, 4.5 mm tall overall Grip grooves: four, 18 mm long Material: PLA or PETG, printed flat
Anglewright — 90° L Profile
Anglewright is a clean 90° L profile with unequal legs: 2 in along one axis and 1.2 in along the other, standing 2 in tall. Both legs are 0.5 in thick, giving a simple right-angle section for corner bracing, spacing, or building up a frame. The form is a single continuous L, so the shape itself carries the function. Dimensions Overall height: 2 in (50.8 mm) Leg lengths: 2 in × 1.2 in (50.8 mm × 30.5 mm) Leg thickness: 0.5 in Corner angle: 90° Print notes At 2 in tall the profile sits comfortably within a typical print bed, so it can be printed standing up on its end with no special base. Lying on its side also works and keeps the flat L section stable on the plate. No supports are needed either way; the 0.5 in legs give plenty of contact area. Features Single-piece right-angle profile with no assembly Unequal legs for mixing offsets in two directions Small enough to print several at once for a set of matched braces
Cactus Pot With Drainage Hole
A cactus pot with a drainage hole, so water leaves the soil instead of rotting the roots. A separate saucer catches the runoff so it doesn't end up on the windowsill. Key numbers Pot: 70 mm base, 90 mm opening, 75 mm tall, 96 mm rim lip Drainage hole: 10 mm diameter, centred in the 6 mm floor Saucer: 90 mm diameter, 12 mm tall, 2.5 mm floor. The pot's 70 mm base sits inside it. Print: no supports needed, both pieces print upright. 0.2 mm layers, PETG or PLA.
Kampas — Mini pakaba su pakeltais galais
Kompaktiška vaikiškos suknelės pakaba su stačiakampe kilpa ir stipriai pakeltais galiukais, kad petnešėlės nenuslystų. Savybės Plotis 10 mm Galiukai pakelti 45° kampu Stačiakampė atvira kilpa Plokščia apatinė dalis pailginta 0,8 mm
Capstop — Magnetic Wall Bottle Opener
Capstop is a wall-mounted bottle opener built around a simple idea: the cap should not hit the floor. A flat back plate carries a cap-catching lip, and a recess behind the opening holds a disc magnet that grabs the cap as it comes off the bottle. The magnet pocket is sized for a 20 mm diameter, 5 mm thick disc magnet, with a small clearance so it seats without forcing. Two countersunk screw holes let the plate sit flush against the wall. Features Back plate, 60 mm wide and 100 mm tall, with chamfered edges Opener lip with a cap slot, projecting from the front face Magnet recess for a 20 × 5 mm disc magnet, located behind the opener Two countersunk screw holes for wall mounting Slim funnel and removable cup intended to sit below the opener to collect caps Dimensions Plate: 60 × 10 × 100 mm Opener lip: 40 mm wide, 14 mm projection, 8 mm thick Magnet pocket: 20.4 mm diameter, 5.2 mm deep Screw holes: 4.5 mm shank, 9 mm countersink Print notes Print the plate on its back or side; the opener lip prints best flat. PETG or ASA is suggested for durability against repeated cap contact. Secure the magnet with a drop of glue if the wall mount sees heavy use.