Tranca de Sobrepor com Tampa Removível
Created today
Description
Tranca de sobrepor compacta (56,5 × 39 × 35,6 mm) em que toda a parte superior do corpo é uma tampa única. Ao retirar os 4 parafusos M3, a tampa sai inteira e deixa o interior à mostra.
O conjunto inclui base com piso de 3 mm, ferrolho, manípulo elevado com serrilha, pino de aço Ø4 mm e receptor separado.
Ideias para remix
- Altura da divisão: a tampa começa no piso (3 mm). Subir esse corte deixa paredes na base e uma tampa mais rasa.
- Manípulo: disco Ø24 mm com 8 mm acima da tampa. Uma alavanca alongada dá mais braço.
- Fixação: 4 furos Ø3,4 mm (34 × 29 mm) com rebaixo, para parafusos 3,5 × 25 mm.
- Combina com: receptor de 40 × 38 mm, que pode ser aparafusado na porta ou no batente.
Images
More like this
Explore more in Home & Fixtures →
Bug Zapper Battery Cover 27.65 x 60 mm
Sliding battery compartment cover plate for a bug zapper, 27.65 x 60 mm. A locating lip sits in the compartment opening, a latch tab sits at one end, and two low retention tabs at the opposite end keep the cover from falling out. Plate: 27.65 x 60 x 2 mm, chamfered edges Lip: 23.65 x 56 mm, 3.8 mm total height Retention tabs: two, 5 mm wide, flush with lip height, at X = ±8 mm Latch tab: 10 mm wide at the +Y end Grip grooves on the outer face Dimensions are estimates; verify against the original opening
Kampas — Mini pakaba su pakeltais galais
Kompaktiška vaikiškos suknelės pakaba su stačiakampe kilpa ir stipriai pakeltais galiukais, kad petnešėlės nenuslystų. Savybės Plotis 10 mm Galiukai pakelti 45° kampu Stačiakampė atvira kilpa Plokščia apatinė dalis pailginta 0,8 mm
Capstop — Magnetic Wall Bottle Opener
Capstop is a wall-mounted bottle opener built around a simple idea: the cap should not hit the floor. A flat back plate carries a cap-catching lip, and a recess behind the opening holds a disc magnet that grabs the cap as it comes off the bottle. The magnet pocket is sized for a 20 mm diameter, 5 mm thick disc magnet, with a small clearance so it seats without forcing. Two countersunk screw holes let the plate sit flush against the wall. Features Back plate, 60 mm wide and 100 mm tall, with chamfered edges Opener lip with a cap slot, projecting from the front face Magnet recess for a 20 × 5 mm disc magnet, located behind the opener Two countersunk screw holes for wall mounting Slim funnel and removable cup intended to sit below the opener to collect caps Dimensions Plate: 60 × 10 × 100 mm Opener lip: 40 mm wide, 14 mm projection, 8 mm thick Magnet pocket: 20.4 mm diameter, 5.2 mm deep Screw holes: 4.5 mm shank, 9 mm countersink Print notes Print the plate on its back or side; the opener lip prints best flat. PETG or ASA is suggested for durability against repeated cap contact. Secure the magnet with a drop of glue if the wall mount sees heavy use.
100x59 Oval Body Hole Cover with Snap Clips
Einsteckbare Abdeckung für eine ovale Öffnung von 100 × 59 mm in etwa 1 mm dickem Blech. Die Frontplatte ist vollständig geschlossen und liegt mit einem 3 mm breiten Auflageflansch rundum auf dem Blech auf; außen misst die Abdeckung 106 × 65 mm bei 2,5 mm Plattendicke. Auf der Rückseite zentriert ein Rahmen mit 2 mm Wandstärke und einer Innenöffnung von 96 × 55 mm als ovales Langloch mit Endradius 27,5 mm. Der Rahmen reicht 7 mm über den Flansch hinaus. Die vier flexiblen Clips – je zwei an den langen Kanten – haben 0,8 mm hohe Haken und angeschrägte Einführflächen; die Rastkante sitzt 7 mm über der Flanschfläche. Mit den verlängerten Federschlitzen baut die Abdeckung insgesamt 13 mm hoch. Bei 1 mm Blech bleibt zwischen Blech und Rastkante in Einsteckrichtung Luft; der Clip rastet erst nach 7 mm Einstecktiefe ein. Werkzeuglose Montage und Demontage Einteiliger Körper, keine Schrauben und kein Kleber Flansch nach unten drucken, in PETG oder ASA Clipsitz beim ersten Druck prüfen, da die Federwirkung des Materials schwankt
Vileda Broom Bar Hook
A bare metal broom top snags on everything, and the mushroom-shaped anchor on a Vileda stick gives a plain hook nothing secure to grab. This replacement end cap sleeves 20 mm down over the sharp top of the stick, then snaps over the anchor on four flexing collet fingers with locking pads. The open hook sits centered over the sleeve so the broom hangs straight on a 27 mm bar, and the flared mouth catches the bar without needing perfect alignment. Fit and print Broomstick: fits a 25.3 mm Vileda stick; the sleeve drops 20 mm over the sharp top edge. Anchor: clears the 13 mm mushroom cap and locks around the 10 mm shaft. The four fingers are 3 mm at their weakest point and taper to 4.5 mm at the base, with a 24 mm relief void and 2 mm slits so they splay outward without binding. Hook: open downward U-channel for a 27 mm bar, not a closed loop; the flared mouth funnels the bar in. Wall: solid plastic separates the flex mechanism from the hook cavity, and the hook sits raised clear of the flex chamber. Printing: lay the 2 mm flat plateau on top of the arch on the bed and print upside down — no supports, the internal ceiling bridges. Feel: the thicker fingers take a firmer push to seat, and hold once they do. Size: 31 mm wide, 63.5 mm deep, 118 mm tall as oriented for printing.
Holdfast — Curtain Rod Wall Bracket
Holdfast is a single-piece wall bracket for a 28 mm curtain rod. A flat 60x60 mm plate carries a 100 mm arm that ends in an open-top half-round cradle, so the rod drops in from above. A small set screw hole through the front wall of the cradle lets the rod be locked in place once seated. The cradle is sized at 28.5 mm inside diameter, giving a snug fit around a 28 mm rod without binding. The arm is kept compact and the cradle walls are thick enough to carry a set screw. Features 60 x 60 x 5 mm wall plate with chamfered edges Four countersunk screw holes (4.5 mm) for flush mounting 100 mm arm projecting from the plate 28.5 mm half-round cradle, open on top for drop-in rod loading 4.2 mm set screw hole through the cradle, level with the rod centre Print notes Tap the set screw hole by hand or use a self-tapping M4/M5 screw. Print with layers running along the length of the arm, since the arm is only 12 mm thick and works under leverage. Use PETG or a similarly tough material for load-bearing use. Parts Wall Plate Arm and Cradle