Pool Noodle End Cap Plug
Created today
Description
A pool noodle end cap that plugs the hole so water, sand and grit stay out of the foam, and the open end stops getting chewed up. The plug uses the same barbed shaft as the noodle connector, so it grips the foam instead of working loose.
Key numbers
- Shaft: 22 mm diameter, 56 mm long, tip chamfered for easy starting
- Barb rings: four, 28 mm diameter, 14 mm apart, chamfered both sides
- Head: 70 mm diameter, 8 mm thick, rounded top edge, stops flush against the noodle end
- Sized for a roughly 25 mm centre hole; foam stretches over the rings
Printing
- Print head-down on the plate, shaft pointing up
- No supports needed, the ring chamfers handle the overhang
- PETG or similar; 3 perimeters for stiffer barbs
Images
More like this
Explore more in Home & Fixtures →
100x59 Oval Body Hole Cover with Snap Clips
Push-in cover for a 100 x 59 mm oval opening in 1 mm sheet metal. The front plate is fully closed, with a 3 mm overlap flange all round (106 x 65 mm outer, 2.5 mm thick). A 2 mm wall locating frame (99.4 x 58.4 mm, 5 mm deep) centres the cover in the opening. Four flexible cantilever clips (two per long edge) have tapered lead-ins and 0.8 mm hooks that lock behind the sheet metal. Tool-free install and removal Single solid body, no screws or glue Print flange-side down in PETG or ASA
Wavy Bobby-Pin Sock Clip
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece. Remix hooks Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin. Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more. Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks. Hook radius: 15 mm. Enlarge it for thicker rack rails. Pairs well with a mesh laundry bag. The clip section is 70 mm long and about 15 mm wide. The hook sits above that.
G 1 1/4" Plug with Concave End
What it's for A male-threaded plug for a G 1 1/4" (BSP parallel) port, such as a bull nose fitting. The end face is dished (concave) so it seats against a rounded nose. Dimensions Thread: G 1 1/4", 41.91 mm major diameter, 2.309 mm pitch (11 TPI) Thread length: 20 mm Hex head: 50 mm across flats, 10 mm tall Concave dish: 30 mm sphere radius, 5 mm deep Remix ideas Change the dish radius or depth to match a different nose profile. Add a gasket groove under the hex head. Swap the hex for a knurled round head for hand tightening.
Cricket Calcium Duster Tube With Inner Screen
A cricket calcium duster tube that keeps powder in one end and crickets in the other. Crickets get dusted when the tube is shaken, because the powder passes up through a screen. The fix is a threaded screen collar between the tube and the powder cap, so nothing prints inside the tube. Key numbers (75% scale) Tube: about 56 mm outside diameter, about 115 mm long, walls about 1.9 mm Threads: about 3.75 mm pitch, same thread on all pieces, so the caps are interchangeable Screen collar: 19 round holes, about 4.5 mm each, in a separate print Powder cap: deep cup for powder, threaded only at the rim Stop flanges: on the tube, so caps seat at a fixed depth Printing Prints open end up, no supports needed PETG recommended, 0.28 mm layers, 10 to 15% infill Four separate parts: tube, powder cap, cricket cap, screen collar
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma