تربة حسينية100
Created 4 days ago
Description
A round pocket case in the spirit of Islamic tilework: a dark cylindrical base with a threaded neck, and a gold-toned cap that screws down over the outside. The cap's top carries a raised eight-point star, petal ring and beaded borders, all geometric with no lettering.
- 40 mm diameter body, 15 mm tall base with a 32 mm storage cavity
- External male threads on the base neck; matching internal threads in the 4 mm cap
- About 0.35 mm radial thread clearance
- Keychain lug with a 3.5 mm hole fused to the base side
- Ornament raised 0.1 mm
Images
More like this
Explore more in Keychains & EDC →
35 mm Threaded Keychain Container, Rosette Lid
Round screw-top keychain container: a deep base with a 35 mm bore and a thin matching lid with an ornamental rim and a twelve-petal rosette centre. Fit Bore: 35 mm diameter, 10 mm deep. Thread: 42 mm major diameter, 2.5 mm pitch, lid cut 0.7 mm oversize. Outer diameter: 48 mm on both pieces. Keyring tab: 4.8 mm hole, on the outside of the base. Check before printing Measure how your printer holds the 35 mm bore. Print the lid first to test the thread fit. Not included No Arabic calligraphy. The lid uses a geometric rosette and scalloped border.
Round Turbah Keychain Container
A 40 mm round container with a press-fit lid and a keyring loop, sized for a 35 mm turbah disc. The lid carries a red medallion with a silver ornamental pattern of petals, dots and rings. It has no text. Remix hooks Interior fit: the cavity is 36 mm wide; change ID for a tighter or looser disc. Height: the base is 11 mm and the lid adds 3 mm for a stack of about 14–15 mm; raise the base height for thicker discs. Ornament: petal count (12 at 30° steps), ring diameters and relief height (0.4 mm) are easy to change. Lid grip: the 30 ribs around the rim can be removed or swapped for a knurl. Colours: print black, red and silver as separate colour regions in a multicolour slicer. Pairs with: a split ring or lanyard clip through the 6 mm loop hole.
Hollow Sphere Keychain, 33 mm Screen Opening
Two-piece hollow sphere keychain with a 33 mm round screen opening in the front and a 3.3 mm ring hole through the top wall. The halves snap together with small bead pegs and can be pulled apart by hand. Body: about 56 mm sphere with two ear bumps, 2 mm wall, flat front face Screen opening: 33 mm diameter, through the front wall into the hollow interior Ring hole: 3.3 mm, a plain hole through the top wall on each side, with no inner sleeve Joint: three bead pegs and undercut sockets, pull apart along the left-right axis Print: each half sits cut-face down, no supports needed for the outer curve
Star Apple Watch Keychain Enclosure
A rounded five-point star shell that holds an Apple Watch SE 44 mm (A2352) as a keychain, with the real display open at the front. Two printed parts: a front shell (print mating face down) and a rear cover (flat face down) joined by four M2 screws. Remix hooks Watch fit: case 44 x 38 mm, 0.4 mm clearance per side, cavity depth 11.2 mm, corner radius 8 mm. Change clr, D and cav_r to tune the fit. Display window: 38.4 x 32.8 mm. This is an estimate, so confirm it against the watch. Crown, button, mic and speaker cutouts: positions are placeholders on the right and left sides. Measure the watch and move them before printing. Star size: the star_pts radii (50 / 33 mm) set the roughly 80 mm span. Shrinking the valley radius thins the wall near the cavity corners. Keyring hole: 5 mm at the top point. Raise ringd or move ringpos for a bigger ring. Charging opening: 32 mm round hole in the rear cover (charge_d). Pairs with: M2 x 8 mm screws, a small split ring, or a TPU bumper variant. Still to verify Crown and button height and position Speaker and mic positions Exact display window size Rear sensor bulge depth Treat the first print as a fit prototype. It is not load-rated.
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
21mm Disk Holder with Snap Lip
What it's for A round holder for a 21 mm by 2.5 mm disk, with an eyelet on each side for a strap, cord or ring. A 0.5 mm lip around the top edge snaps over the disk to keep it in place. Dimensions Outer diameter: 27 mm, 4.7 mm tall Disk pocket: 21.4 mm diameter, 2.5 mm deep Retaining lip: 0.5 mm overhang with a tapered lead-in Rear window: 17 mm, for pushing the disk out Eyelets: 4 mm holes, 9 mm pads, on both sides Remix ideas Increase the lip overhang for a firmer grip Remove the rear window for a closed back Add text or a chamfer ring around the edge