3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Raised-Text Visitor Pass 110x70 mm
A 110 × 70 mm single-piece visitor pass for Himalaya Public Sr. Sec. School, with a 2 mm base plate and bold text raised 0.8 mm above it. The three centred lines read HIMALAYA PUBLIC, SR. SEC. SCHOOL and VISITOR PASS. Plate: 110 × 70 mm, 2 mm thick, rounded corners, flat bottom Text: 0.8 mm raised, fused to the plate Total thickness: 2.8 mm Single colour, no supports needed Text size unchanged from the previous version
Phone Stand with Cable Channel
A phone stand that holds the phone upright in portrait or landscape, with a cable channel so the charger doesn't pin the phone down or dangle off the edge. Most stands either tip the phone back too far to tap or force the cable to loop around the outside. This one leans the phone at 70° from horizontal and routes the cable up through the stand to the back of the phone. What decides fit and print Lean angle: 70° from horizontal, steep enough to tap the screen and upright enough to watch video. Groove: runs the full 90 mm width, so the phone sits in it in either orientation. It is sized for a phone in a thin case. Cable channel: 12 mm wide, open on the underside of the base. It runs in from the back, then rises through a 12 x 12 mm opening in the groove floor. Overall size: 90 mm wide, about 56 mm deep and 70 mm tall. Printing: the flat base goes down on the bed. The underside channel is a 7 mm-tall tunnel, so print it with bridging on or light supports. No other supports are needed. Material: PLA or PETG both work. Use 3 or more perimeters for a stiffer groove lip.
Single-Colour Raised Text Visitor Pass
A 110 × 70 mm visitor pass with a 1.2 mm plate and bold raised lettering standing 0.6 mm proud, 1.8 mm total. It prints flat-side down in one colour with no supports. Remix hooks Text sizes: 6.5 mm for the school lines and 7.5 mm for VISITOR PASS. Raise them for a bolder look, but keep 4 mm of edge clearance. Plate thickness: 1.2 mm. Thicker gives a stiffer card, though the total height rises with it. Relief height: 0.6 mm. Match it to your layer height, for example 3 layers at 0.2 mm. Pairs with: a lanyard slot or clip tab added at one end.
Jennifer — Two-Colour Baptism Cake Topper
Jennifer is a two-colour baptism cake topper with a slim Latin cross, a laurel wreath ring, the name in flowing script, a curved Baptism banner and a pointed stake for the cake. Features Slim Latin cross with a long stem, shorter crossbar and ivory inset Gold ring with mirrored leafy branches Ivory "Jennifer" script connected to the ring by thin bars Curved banner with evenly spaced raised "Baptism" letters Pointed stake; wrap it in food-safe film or a cake dowel before use Print notes Designed for two-colour printing in gold and ivory Base 1.6 mm, raised details up to 2.8 mm (banner letters 4.1 mm)
Stitch Head Bead With Ears
A round Stitch-style head bead with two pointed ears, a lighter face patch, eyes and a nose, threaded by a vertical hole for cord or wire. Remix hooks Head size: the head radius is 13 mm (26 mm across). Scale it down for jewelry-sized beads; keep the hole at 3.5 mm or larger for cord. Hole diameter: 3.5 mm runs top to bottom between the ears. Widen it for paracord or narrow it for thin elastic. Ear angle and length: ears are about 21 mm long, splayed 55° outward. Lower the angle for droopy ears, or shorten them for a chunkier keychain bead. Colours: the head, face patch, inner ears and eyes are separate regions, so they suit multicolour printing with filament swaps. Pairs with: plain round spacer beads, a keyring clasp, or a row of beads for a bag charm.
Cross Arm Traffic Light Pole Model
A miniature traffic light pole with a horizontal cross arm, built as a single-piece STEM teaching model. A hexagonal base keeps the 90 mm round pole upright. The 45 mm arm carries a slide-in holder at its end for a 52 × 22 mm traffic light PCB module. Pole: 12 mm diameter, 90 mm tall, on a 44 mm hexagon base Arm: 45 mm from the pole axis, with a 45° brace underneath so it prints without support Holder: 2.2 mm walls, edge lips, and a top stop. The board slides in from below Rear clearance: 6 mm gap behind the board, open on the cable side for the 5-pin connector Board fit: assumes 1.6 mm thickness with 0.2 mm play per side Prints upright in PLA as one piece.
Mister Box Holder with Open Front
A wall-mounted cradle for a 2.25" x 4.75" x 2" mister box, sized with extra width clearance and a little extra depth so the box slots in easily but can't tip forward out of it. The front is open below a solid top rim so the buttons stay reachable, and a low lip along the bottom front edge holds the box in. Two identical ears on the back face carry countersunk screw holes for mounting to the side of furniture. Full 4.75" (120.65 mm) wall height 10 mm width gap, 3 mm depth gap Cord notch in the left rim only, 15 mm wide, centered 1.5" from the inside back wall, open at the top Window cutouts on the sides to save filament Two back ears with countersunk screw holes
Anel de Guardanapo com Cruz
Anel de guardanapo com cruz lisa à frente, ligados por uma ponte sólida, para o tecido não escorregar nem o conjunto soltar. Medidas principais Furo do anel: 38 mm de diâmetro (raio interno 19 mm), aberto de ponta a ponta Parede do anel: 3 mm Altura do anel e da ponte: 7 mm Cruz: 57,2 mm de altura, braço de 39,6 mm Ponte: 10,4 mm de largura Impressão Peça única, sem partes soltas O anel fica elevado, então pode pedir suporte sob ele PLA ou PETG
Moldura A4 Vertical em Três Peças
Moldura para folha A4 (210 × 297 mm) na vertical, dividida em duas metades com pinos-guia, mais um gancho impresso separadamente que encaixa na borda inferior. Externo: 250 × 337 × 15 mm Abertura visível: 202 × 289 mm Bolso do papel: 212 × 299 mm, entrada pela fresta superior 4 pinos-guia de Ø5 mm entre as metades, folga de 0,15 mm Keyhole para prego na travessa traseira superior Gancho separado: dois pinos de 4 × 5 × 8 mm encaixam em furos na metade inferior O gancho é impresso apoiado no pé, com os pinos para cima. Cada metade mede 250 mm de largura, então confira o tamanho da mesa antes de imprimir.
Saipa Pride 111 Clock Bezel Phone Cradle
Preliminary replacement for the Saipa Pride 111 (2011 / 1390) dashboard clock bezel, with a landscape cradle for the Samsung Galaxy A54 5G. All bezel dimensions are placeholders and not taken from the car. Fit status Host: Saipa Pride 111 clock opening. Bezel size, spigot depth and clip positions are placeholders. Phone: Galaxy A54 5G, 158.2 × 76.7 × 8.2 mm, plus 3 mm case allowance and 1 mm clearance per side. Does not fit other Pride trims or other phones. Measure before printing Dash opening width, height, depth, corner radius and clip or screw positions. Notes The cradle is wider than the clock opening, so it projects forward of the dash. Open-top slide-in loading, side lips, a bottom ledge and a USB-C side slot. Tilt is 15° back. Check it against the dash and your sight line. Print in ASA or PC-CF. PETG softens in a hot parked car.
Klassisk spillebrik uden support
En traditionel spillebrik til brætspil som gåsespil: bred rund fod, aftagende kegleformet krop, en lille krave og et kugleformet hoved. Samlet højde ca. 33 mm, fodens diameter 22 mm. Hele brikken printes stående uden support. Remix-muligheder Fodens diameter (22 mm): gør den bredere for mere stabilitet, eller mindre, hvis felterne på brættet er små. Højde: kroppen er 14 mm høj. Forlæng den for en mere slank brik, der er nem at gribe. Hovedet (14 mm kugle): skift til en terning, en cylinder eller et nummer, så hver spiller kan kende sin brik. Farve: print i forskellige filamentfarver, eller lav et hul i bunden til en lille magnet eller en vægt. Passer til andre brætspil, hvor brikkerne skal stå på felter på ca. 25 mm eller mere.
Domed Wickiup Terrain Shelter
A hollow dome structure designed to represent a wickiup or wigwam shelter. Useful as tabletop terrain or a diorama element. Overall Size: 100 mm diameter footprint Structure: 3 mm wall thickness Features: Domed exterior, arched front entryway, and a central top vent hole Base: Sits flat on the build plate for easy printing
5 x 5 x 1 mm Square Block
A plain square block measuring 5 mm by 5 mm by 1 mm, flat on the bed and ready to print. Remix hooks Footprint: 5 x 5 mm is the starting value. Change it to make a tile, spacer or shim. Thickness: 1 mm is about five layers at 0.2 mm. Raise it for a sturdier piece. Edges: Add a small chamfer or rounding for a softer look. Keep it under 0.5 mm at this size. Pairs with: Use it as a test cube for tolerance checks, or as a base for a hole, text or a peg.
siena
A flat, solid back panel that closes the open back of the doll wardrobe. It matches the wardrobe's outer outline exactly, so it can be glued straight onto the back face. Remix hooks Thickness: 3 mm now, matching the original back frame. Raise to 4–5 mm for a stiffer back. Size: 250 × 250 mm, the same as the wardrobe body. Change both values together if the wardrobe is resized. Edge treatment: left square. A small chamfer would help with elephant foot, but would leave a visible gap at the corners. Glue area: the 10 mm frame and the side walls give the contact surface. A shallow locating lip could be added if you want self-alignment. Pairs with: the hinged-door wardrobe body, printed flat on its back.
Square Bust Base Removable Lid
What it's for A removable square lid with a cornice top and a hollow locating lip. It was designed to cap a box-style bust base and lift off. Dimensions Cornice: 62 × 62 mm Upper step: 57 × 57 mm Lip: 46.6 × 46.6 mm outer, 1.5 mm wall, 4 mm deep Printed upside down so it sits flat Remix ideas Add a matching base sized to the lip. Engrave a name or date on the top face. Change the lip size for a looser or tighter fit.
Cyclops Visor Smart Goggles Chassis
A wearable housing for smart-glasses electronics, with a chunky sci-fi visor silhouette: twin rounded lens bays, front camera ports, and downward sensor holes. Hollow temple arms hold speakers and haptics, and a separate electronics box carries the main board. The frame now comes with two cover caps that close the rear eye cavities, so the electronics inside stay protected. Design notes Frame caps: 56 x 48 mm plates with a plug lip that seats in each eye cavity Camera ports: 8 mm wide, 24 mm deep Electronics box with its own lipped lid Arms hinge with 3 mm pins or filament offcuts Prints as separate flat parts, no supports needed
Ripple Dune Twist-Lock Lamp
A soft, dune-rippled shade sits on a rounded pedestal base, like a small sand-sculpture lamp. The two pieces lock together with a printed twist-lock joint, so no hardware is needed. A bulb holder pocket sits inside the shade, and the cable runs through the base. Design notes Three lugs on the base neck drop into slots in the shade, then a short twist locks them. The cable hole enters the rear of the base and rises through the neck into the bulb pocket. The 24 mm pocket suits a small E14-style lamp holder. Use a low-heat LED bulb. Prints as two parts, base flat on the bed and shade open end down.
Eccentric Duct Adapter 125mm
What it's for Bathroom duct adapter that connects a round duct to a flat rectangular duct. Both ends are female sockets, and the airflow passage is fully open. The round socket has a wide bore for a loose, free fit. Dimensions Round socket: Ø142.5 mm inner, Ø147.3 mm outer, 30 mm long, 1.5 mm entry chamfer Flat socket: 222 × 92 mm inner, 5 mm corner radius, 30 mm long Transition: 160 mm, smooth round-to-rectangle loft Vertical offset of the flat socket: 72.5 mm Wall thickness: 2.4 mm Overall length: 220 mm Remix ideas Change the bore diameter to tune the fit for a different duct. Adjust the vertical offset for another mounting position. Lengthen the sockets for a deeper grip.
Mango con soporte de cuchara giratorio
Mango recto de 9,4 cm con un soporte giratorio para pegar una cuchara. Son dos piezas independientes, dispuestas lado a lado en la cama para imprimir sin soportes en el soporte. Se unen con un tornillo M4 × 16 mm y una tuerca hexagonal M4 (no incluidos). Ideas para remezclar Holgura mango–soporte: 2 mm ahora. Bájala a 1 mm para limpiar mejor, o súbela si buscas más seguridad para los dedos. Holgura vertical: 0,4 mm entre soporte y disco. Si las piezas quedan pegadas al imprimir, sube a 0,5 mm. Brazo del soporte: 36 × 20 mm y 10,6 mm de grosor. Ensanchar la cara plana o añadir un asiento para el mango de la cuchara es el cambio más útil. Material: PETG recomendado por el calor de la cuchara. Combina con: tornillo y tuerca de acero inoxidable, o una tuerca autoblocante. Medidas: largo total 12 cm, ancho máximo 2,8 cm, alto 1,6 cm.
Christmas Tree Lantern for LED Tealight
A Christmas tree lantern that sits over a battery LED tealight, so the light stays hidden inside instead of glaring from a bare tealight on the table. The walls are perforated with rings of small round holes that throw dots of light, and the bottom is open so the LED can be placed or swapped without taking anything apart. Key numbers Height: about 135 mm including star Base diameter: 90 mm, open underneath (inner opening about 87 mm) Wall: 1.6 mm, three stacked tiers Perforations: 4.2 mm holes, staggered rings Star: separate colour, peg-mounted into the top tier Printing Print upright, open end down, no supports needed for the cone walls Green for the tree, gold or yellow for the star Use a 0.4 mm nozzle; a lighter or translucent filament glows more
3-Inch "Glad to Be of Service" Door Plaque
A 76 × 76.2 mm (3 in) square plaque carrying "GLAD TO BE OF SERVICE" in raised lettering, styled after the cheerful talking doors of The Hitchhiker's Guide to the Galaxy. Layout GLAD and SERVICE are set large for emphasis; TO BE OF sits small between them. Retro sci-fi lettering, a raised border and a small smiley under the text. Backing plate is 2 mm thick; lettering and border rise 1.6 mm above it. Check before printing Overall height is 76.2 mm. Scale the whole plate if you need a different size. The smallest line, TO BE OF, is 7 mm tall, so use a 0.4 mm nozzle or finer. There are no mounting holes or stand.
バルブ、サーボケース（仮）
A small bunker of a box: thick walls braced by tapered buttress ribs, a ribbed underside, and a flat screw-down lid that lifts straight off the top. Built as a housing for a servo-driven rotary valve, with a completely empty interior. Design notes Size: 60 × 100 × 40 mm overall, including the lid and all ribs. Ribs: tapered gusset-style ribs on all four walls, plus underside ribs the body stands on when printing. Corners: rounded, with four blended screw bosses that double as corner reinforcement. Lid: 4 mm, with countersunk M3 clearance holes into pilot holes in the bosses. Hose holes: 6 mm, on one shared vertical axis; the Y and X positions are editable parameters (Y defaults to 20 mm off centre). Floor: flat and clear of obstructions.
Organischer Kopfhörerständer in Rosa
Kopfhörerständer mit breitem, abgerundetem Bogen, geschwungenen, sich kreuzenden Streben und einer flachen, wellenförmigen Standfläche. Ein zusammenhängender Körper, flach druckbar, gedacht für pastellrosa PLA. Remix-Ansatz Bogen: Außenradius 65 mm, Strebenbreite 22 mm. Größerer Radius für breitere Kopfbügel. Streben: Vier Kurven, Kontrollpunkte frei verschiebbar für andere Öffnungen. Basis: ca. 224 × 150 mm, 8 mm hoch. Dicker oder mit Gewicht-Einlage für mehr Standsicherheit. Tiefe der Streben: 36 mm, anpassbar. Gesamthöhe ca. 260 mm.
Mango recto con soporte giratorio
Mango recto con soporte giratorio para cuchara, de 12 cm de largo total, 2,8 cm de ancho y 1,6 cm de alto. Se compone de dos piezas independientes unidas por un tornillo M4 vertical y una tuerca hexagonal en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Largo total: 12 cm Mango: unos 9,4 cm, se afina hacia el extremo Lengüeta de 4 mm con disco de 20 mm y orificio de 4,6 mm Soporte con ranura de 4,4 mm y alojamiento para cabeza de tornillo y tuerca M4 Tornillo y tuerca no incluidos
Need a part that doesn't exist yet?
Start building →