3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Mango curvo con soporte de cuchara giratorio
Conjunto de dos piezas independientes: un mango curvo de 120 mm y un soporte de cuchara que se encaja sobre su extremo. La unión se hace con un tornillo M4 vertical, introducido desde arriba, y una tuerca en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Especificaciones Mango: 120 mm de largo, 25 mm en la base, 20 mm en el extremo, 16 mm de grosor. Lengüeta del mango: 4 mm de grosor, disco de 20 mm, orificio de 4,6 mm. Soporte: ranura de 4,4 mm, orificio pasante de 4,6 mm. Cabeza del tornillo alojada arriba; tuerca M4 hexagonal alojada abajo. Alojamiento de la cuchara: 14 × 5 mm. Tornillo y tuerca M4 no incluidos.
Cucharilla de dos piezas con conector
What it's for Mango curvo tipo banana y conector independiente con dos pestañas flexibles. El conector encaja con un clic en el alojamiento del mango y se retira pellizcando las pestañas a través de las ventanas laterales, sin herramientas. Dimensions Mango: 120 mm de largo, 25 mm de ancho en la base y 20 mm en la punta, 16 mm de grosor. Alojamiento: 16 × 6 mm, 23 mm de profundidad. Conector: núcleo de 22 mm, 5,6 mm de grosor, brazos de 1,6 mm con resalte de clic. Ventanas laterales de 4 mm donde se aloja el resalte. Remix ideas Añadir una cabeza de cuchara en la pestaña tope del conector. Ajustar el grosor de los brazos (1,6 mm) para un clic más suave o más firme. Cambiar el radio de curvatura del mango.
3×2 Fächergitter 40×40 mm, 60 mm hoch
Fächergitter mit sechs durchgehenden Schächten (3 nebeneinander, 2 hintereinander), oben und unten offen. Gedacht als Sortier- oder Einsatzraster für Teile, die in einen 40 × 40 mm Schacht passen. Maße Fach innen: 40 × 40 mm Höhe: 60 mm Wände: 2 mm, auch zwischen den Fächern Außenmaß: 128 × 86 × 60 mm Steg: umlaufender Rand bei 20 mm Höhe, 2 mm dick, 5 mm breit; Öffnung dort 30 × 30 mm Vor dem Drucken prüfen Der Steg ist eine Annahme: ein umlaufender Rand in jedem Fach. Ein Teil, das durch das Fach muss, braucht Platz im 30 × 30 mm Durchlass. Passt nicht Gegenstände über 30 mm Breite passen nicht durch die Stegöffnung.
Moldura A4 Vertical 250 × 337 mm, Fundo Aberto
Moldura para folha A4 (210 × 297 mm) na vertical, em duas metades unidas por pinos-guia, com a folha entrando por uma fresta na travessa superior. Medidas Externo: 250 × 337 × 15 mm Abertura visível: 202 × 289 mm, lábio frontal de 5 mm Bolso do papel: 212 × 299 mm Fresta superior: 206 mm de largura Fixação e encaixes 4 pinos-guia de Ø5 × 8 mm na metade superior, com alojamentos de Ø5,6 mm na inferior Keyhole para prego: entrada de Ø10 mm e fenda de 4,2 mm, na travessa traseira superior Gancho na borda inferior frontal Verifique antes de imprimir Cada metade mede 250 mm de largura, acima dos 220 mm de uma impressora comum. A traseira é aberta abaixo da travessa do keyhole, então nada segura a folha por trás. Não serve para papel muito fino ou ondulado.
108 mm Vent Grille Cap, Center-Rib Clearance
Closed 108 mm rounded-square cap for an installed round vent grille (about 99 mm body, 108 mm flange), with a dedicated recess over the raised center rib. Fit Fits over: round grille up to about 100 mm, flange up to about 101.5 mm square. Face: 4 mm, fully closed. Cavity: 100.5 mm round, 15 mm clearance above the grille, plus a 24 mm wide channel along X reaching 21 mm clear. Lip: 10 mm deep, 3 mm walls, 102 mm pocket, eight small friction bumps. Check before printing Measure the center rib's height and direction. The channel assumes it runs along X and stays under about 18 mm tall. Not compatible Flanges over 101.5 mm square or grilles wider than 100 mm.
Moldura de Parede A4 com Gancho
Moldura de parede para folha A4 com gancho em J fechado na borda inferior e suporte para prego escondido no verso. A folha desliza pela abertura no topo e fica num rebaixo atrás da janela. O gancho tem a aba de retorno voltada para a moldura, formando uma abertura fechada. O suporte com furo de fechadura fica na parte de trás, no topo, e não aparece de frente. Moldura externa: 240 x 327 mm Janela: 196 x 283 mm Gancho em J: 16 mm de largura, 24 mm de altura Suporte de prego: aba traseira de 4 mm com furo de fechadura
Ø20 mm Marker mit Zier-Fragezeichen
Runder Spielmarker, Ø20 mm und 3 mm hoch, mit einem verzierten Fragezeichen auf dem Sockel. Er passt als Hinweis- oder Rätselmarker auf Spielfelder. Maße und Aufbau Sockel: Ø20 mm, 2 mm dick, obere Kante mit 0,3 mm Fase Fragezeichen: 1 mm erhaben, Gesamthöhe 3 mm, ca. 14 mm hoch Details: Endknopf am Bogen, Zierperle im Schaft, Punkt mit zwei Zierspitzen Zierrand: schmaler Ring mit zwölf Perlen, 0,6 mm erhaben Vor dem Druck prüfen Der Zierring liegt bei Ø18 mm. Wenn der Spielfeldrand oder eine Halterung enger ist, vorher messen. Passt nicht Kein Ersatz für Marker mit anderem Durchmesser als 20 mm.
V2_Aşkım Love Letter Photo Frame
Ein winziger Bilderrahmen im Stil einer Liebeskarte: Der Name „Aşkım" thront als erhabene Schrift über dem Rahmen, auf der Rückseite wartet eine versteckte Botschaft samt großem Herz. Außenmaß 52 × 52 × 1,5 mm, Fach für ein 50 × 50 mm Foto Rückwand 0,6 mm, geschlossen Name 4 mm hoch in Arial-ähnlicher Schrift (Liberation Sans) Unterseite: Widmungstext und Herz, 0,25 mm tief graviert (lesbar von hinten)
Doll Wardrobe With Opening Doors
Doll wardrobe whose doors stay shut and never swing, because they are glued-on slabs. This one has two doors on pin hinges that actually open, with a centre divider and a hanging rail inside. Key numbers Overall size: 200 mm long x 50 mm deep x 200 mm high Walls and shelves: 6 mm; back panel 4 mm Doors: 4 mm thick, sit flush in the front opening with 0.6 mm clearance Hinge pins: 3 mm, in 3.8 mm sockets in the top and bottom panels Hanging rail: 5 mm round bar, 30 mm below the top Printing Print the body upright, open front facing you. Print the doors standing on their long edge, pins pointing up and down; pin ends need no supports. Drop each door's lower pin into its socket first, then tilt the top pin in. Rail and knobs are separate pieces to print and glue in place.
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament
Indian Number Plate Keychain HR82 6791
A rectangular Indian-style number plate keychain with the registration HR82 6791 in raised black letters on a white plate. 70 × 20 mm plate, 3 mm thick, with rounded corners Text raised 0.75 mm for clean printing with a 0.4 mm nozzle 4 mm ring hole on the left side Flat back, no supports needed Single connected piece, white base with black text
110×70 mm Himalaya School Visitor Pass
Two-body visitor pass for Himalaya Public Sr. Sec. School: a white 110 × 70 × 4 mm plate with 3 mm corner radius, and solid dark-blue raised lettering. Fit and dimensions Plate: 110 × 70 × 4 mm, rounded corners. Letters: 2 mm proud of the plate, flat bottoms seated on the top face (overall height 6 mm). Text: HIMALAYA PUBLIC / SR. SEC. SCHOOL / VISITOR PASS, centred, well inside the 4 mm margin. Check before printing Confirm the text stays within 4 mm of every edge in your slicer. Assign the white and blue bodies to separate filaments. There is no hole or lanyard slot.
Flat L Bracket 15mm Strap
A flat L-shaped strap bracket with a 15 mm wide, 5 mm thick strap. Inside edges measure 70 mm along X and 65 mm along Y, giving an overall footprint of 85 × 80 mm. Five 5.5 mm holes suit M5 screws in 2020 extrusion slots. Remix hooks Arm lengths: the inside lengths (70 mm X, 65 mm Y) are the main parameters to change. Strap width: 15 mm now. Widening it allows holes offset from the centreline. Hole pitch: pairs are 20 mm apart, with the first hole 12.7 mm from the free end. Change the pitch for other slot spacings. Hole size: 5.5 mm clearance. Go up for counterbores or down for M4. Pairs with: 2020 extrusion, M5 T-nuts and button-head screws.
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Apothecary Drawer Hex Key Rack
A row of nine upright hex pockets, like a pharmacist's labelled vial rack, scaled down for the workshop wall. Each long-arm Allen key stands in its own slot, sorted from 1.5 mm up to 10 mm, with the metric size embossed on the front face beside it so the right key is readable at a glance. Every pocket is a hex cut to its key's across-flats size plus 0.3 mm of clearance, 22 mm deep, so keys drop in and lift out without wobbling loose. Two counterbored screw holes near the ends let the rack mount flat to a wall. Design notes Fits the standard metric set: 1.5, 2, 2.5, 3, 4, 5, 6, 8 and 10 mm Overall size about 120 mm wide, 20 mm deep, 30 mm tall Embossed labels are a separate colour region for multi-colour prints or a filament swap Chamfered outer edges for a cleaner print and a softer look The 1.5 mm slot is the tightest fit, so check it on a first print Remix hooks: change pocket depth, enlarge the label text, or add more slots for imperial sizes
Lamp Bases, Shades and Diffuser Set
A set of mid-century lamp parts that all share one coarse 6 mm-pitch thread, so any shade fits any base. The set has two fluted shades (round and square ribs), a white adjustable diffuser and several bases: tall, short, grooved, two tripods, a flat-leg grooved tripod and a dowel-leg hub. Remix hooks Flat-leg tripod: legs are 16 mm wide slabs (before scaling) with two grooves, 3.2 mm wide, down each outer face. Change the groove count, offset (±4 mm) or width. Leg height and spread: hub height 70 mm and foot radius 70 mm set the splay. Raise both for a taller version. Thread spigot: 52 mm across, 38 mm long. Keep it to stay compatible with the shades. Pairs with: either fluted shade and the diffuser. The 42 mm bore runs straight through for the bulb and cord.
Teardrop Lamp Parts, Terracotta and Wood
A mid-century teardrop table lamp laid out as separate print pieces: fluted base, threaded crown collar, hollow prolate-spheroid diffuser and three dovetail-cleat prongs. A second set of the base, crown and prongs is included in a walnut-style wood tone, so one diffuser works with either finish. Remix hooks Wood finish: the wood set is the same geometry in a different colour. Print it in wood-fill or walnut-toned filament, then sand and oil it. Real grain would need a textured surface, which is a good next step. Fit: the thread clearance is about 0.4 mm and the cleat clearance about 0.3 mm. Adjust these to suit your printer. Bulb: it is sized for a 127 mm T10 or an ST19. The crown bore is 31 mm and the diffuser opening is 36.5 mm. Pairs with: an E26 socket, plus a small glue dab or set screw if you want the cleats locked. The tallest piece, a prong, is about 203 mm, so everything fits a 256 mm bed.
Wazowski — Hinged Arms, Viper Horns
Wazowski is a set of two hinged monster arms and two horns, made to sew onto a maternity shirt panel. Each arm splits into an upper arm and a forearm with hand, and the horns are slender, backward-curving thorns in the style of a desert horned viper. Features Upper arm with a single lower hinge plate. The top plate is left off so the forearm can be glued in place. Forearm and hand with three fingers and a thumb, plus a short pin that locates in the hinge hole. Two horns, 60 mm tall, tapering to a fine tip with a slight curve. Round flanges with six sewing holes on each arm and horn. Print notes Print the arms in TPU or another flexible filament so they move with fabric. Glue the forearm knuckle onto the hinge plate with the pin seated in the hole. Proportions are set for scaling, so resize in the slicer to fit.
Slipbar — Snap-On G Cap
Slipbar G Cap is a standalone G-shaped cover that snaps onto the corners of a 68 × 38 × 10 mm rectangular buckle frame. The plate itself is the letter G, stretched to fill the frame's face, with a small clip at each corner. Features G-shaped plate, about 71.6 × 41.6 mm Four corner clips with small inward lips that catch the frame's lower edge Mirrored so the G reads correctly from the front face when printed face-down Print notes Print with the front face on the build plate PETG flexes best for the clips Test-fit the snap and adjust the lip if it is too tight or loose
Mandarin Town — Colorful Community Scene
A bright miniature town for learning Mandarin community vocabulary. Each building carries its name in Chinese, pinyin and English, and every main building has its own wall colour. Signs, a park, a pond, houses, cars and people fill out the scene. Features Hospital, library, community center, store and school, each in a different colour Park with pond, benches and trees, plus a banner reading 一起参加活动 Road with cars, footpaths, lamps and neighbourhood houses Work and Service signs with people at the buildings Dimensions 200 × 200 mm base plate, 4 mm thick
Mandarin Community Town Model
A tabletop town for practising Mandarin place words, where flat labels get lost. Each building, sign and park area carries its Chinese characters, pinyin and English on the front face, so the vocabulary sits right on the thing it names. Details that matter Base: 200 × 200 mm, 4 mm thick plate Buildings: hospital, library, community center, store and school, each 46 × 28 mm footprint Extras: park with pond, road, footpaths, houses, cars, trees, lamps and figures Colour regions: ground, road, walls, roofs, doors, lettering, signs, trees, lawn, pond, paths Print: large bed needed (or scale down); multicolour or paint by region; lettering is 0.8 mm raised, so use a 0.4 mm nozzle
Mandarin Community Town Model
What it's for A small-town community model for a Mandarin class project. Each facility carries a Chinese, pinyin and English label, and the action words appear on signs, a banner and people scenes. Dimensions Base: 200 × 200 mm, 4 mm thick Buildings: 46 × 28 mm, 32 mm tall Labelled places: 医院, 图书馆, 社区中心, 商店, 学校, 公园 Action words: 工作 and 服务 on signs, 一起参加活动 on the park banner, with people grouped together Extras: road, paths, trees, houses, cars, benches, streetlights, neighbours Remix ideas Add more houses with 邻居 labels Swap the school for another facility Print in several colours to paint or assemble per group
Drill Press Column Tray with Key Slot
A C-shaped clip that snaps around a 60 mm drill press column, with a 120 mm round dished tray attached at the front. The tray holds drill bits, chuck keys and small parts within reach while you work. The clip opening is narrower than the column, so it snaps on and grips by spring tension. Lead-in lips on both sides of the opening guide it onto the column. A slot on the front rim of the tray holds the chuck key, so it stays off the floor. Clip: fits a 60 mm column, 30 mm tall, 5 mm wall Tray: 120 mm diameter, 18 mm tall, with a 3 mm floor and a dished cavity Key slot: on the front rim, 9 mm wide, sized for a chuck key shaft Print the clip upright with the tray on the plate. PETG or ABS gives the clip better flex and durability than PLA.
Wargaming Reroll and Modifier Tokens
A set of nine one-sided 25 mm tabletop tokens for tracking modifiers and rerolls: +2 F, +2 R, +1 R, Reroll impactar, Reroll herir, Rerrol 1's impactar, Rerrol 1's herir, -1 R and -1 F. Each token has a 3 mm navy base with a 1 mm raised rim, text and four compass dots, sized for a filament swap at Z = 3 mm. Remix hooks Text size: short labels use 6 mm, two-line labels use 3.5–4 mm. Longer strings need a smaller size to stay clear of the dots at 10.5 mm radius. Line spacing: two-line labels sit at ±2.5 mm from centre; widen it for taller text. Colours: base and accents are separate bodies, so any two-colour pairing works. Spelling: "Rerrol 1's" is kept as supplied; change it to "Reroll 1's" if that was a typo. Pairs with: the earlier Invuln./No hay dolor set on the same 30 mm grid.
Need a part that doesn't exist yet?
Start building →