3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Raspberry Pi 5 Gehäuse mit Lüfterplatz
Zweiteiliges Gehäuse für den Raspberry Pi 5 mit Ausschnitten für alle Anschlüsse und einer Montageoption für einen 30×30-mm-Lüfter im Deckel. Lüfter: 30×30 mm, Lochabstand 24 mm, runde Öffnung 27 mm über dem Prozessor Befestigung: vier Domen innen im Deckel, Bohrung 2,7 mm für M3-Schrauben (selbstschneidend, ca. 10–12 mm) Ausschnitte: USB, Ethernet, USB-C, 2× Micro-HDMI, FPC, SD-Karte, GPIO, Lüfter-/RTC-/PCIe-Anschluss Lüftung: Bodenschlitze und Deckelschlitze Druck: Unterteil und Deckel liegen getrennt auf dem Druckbett
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
Yoshi Saddle Shell Backpack Mount
A red Yoshi-style shell dome on a white base plate that straps onto a backpack. What it's for Turns a backpack into a Yoshi costume piece. Webbing passes through four slots in the base plate, so the shell sits on the backpack's outer face. Dimensions Overall: about 214 × 175 × 94 mm, fits a 256 mm bed in one piece Dome wall: about 4 mm, hollow underneath Base plate: 6 mm thick Strap slots: four, each 44 × 7 mm, at X ±60, Y ±32 Remix ideas Add white spots or a ridge band on the dome Widen the slots for thicker webbing Add a foam pad under the base plate
Elipsa
Izduženi ovalni okvir u obliku glatke kontinuirane trake, širine 80 mm, kao elegantna orbita bez ikakvog teksta unutra. Donji luk je širi i izraženiji od ostatka, a cijela traka leži na ploči, bez dijelova koji vise u zraku. Visina gornjeg i bočnog dijela: 0,8 mm Visina donjeg luka: 1,8 mm Širina trake: 2,4 mm, a na donjem luku 3,8 mm Ravna baza, prilagođena FDM štampi
Star Apple Watch Keychain Enclosure
A rounded five-point star shell that holds an Apple Watch SE 44 mm (A2352) as a keychain, with the real display open at the front. Two printed parts: a front shell (print mating face down) and a rear cover (flat face down) joined by four M2 screws. Remix hooks Watch fit: case 44 x 38 mm, 0.4 mm clearance per side, cavity depth 11.2 mm, corner radius 8 mm. Change clr, D and cav_r to tune the fit. Display window: 38.4 x 32.8 mm. This is an estimate, so confirm it against the watch. Crown, button, mic and speaker cutouts: positions are placeholders on the right and left sides. Measure the watch and move them before printing. Star size: the star_pts radii (50 / 33 mm) set the roughly 80 mm span. Shrinking the valley radius thins the wall near the cavity corners. Keyring hole: 5 mm at the top point. Raise ringd or move ringpos for a bigger ring. Charging opening: 32 mm round hole in the rear cover (charge_d). Pairs with: M2 x 8 mm screws, a small split ring, or a TPU bumper variant. Still to verify Crown and button height and position Speaker and mic positions Exact display window size Rear sensor bulge depth Treat the first print as a fit prototype. It is not load-rated.
Folding Hex Easel Vise With Strut Links
A folding bench-vise and easel stand: a honeycomb-cut backrest on a hinged base ledge, two jaws driven by threaded crank rods, and a rear support leg held by a two-stick folding strut on each side. The strut is built from two flat sticks joined at an elbow pin. Push the leg in and the elbow bends, so the two sticks fold down alongside each other and act as one. The sticks sit outside the handwheels in X, so they pass beside the cranks and not through them. Remix hooks link_k (0.52): stick length as a fraction of the base-to-knee distance. It must stay above 0.5. Higher values give a bigger elbow bow and a longer reach. platelean (20°) and legang (25°): raise them together for a steeper recline. rodz (60 mm) and jawx (27 mm): crank height and jaw start position. hd and wall in the hex cutter (11 mm and 3 mm): change them for a denser or sparser honeycomb. phonew, phonet and phone_d (80, 10.5 and 3 mm): the phone slot. leg_lock: switches the knee stop tabs on or off. Pairs with Longer or thicker stick bars (4 mm wide now) for heavier loads. 4 mm filament offcuts as hinge and elbow pins.
Smart tap attachment
Assembled touchless tap attachment: a 110 × 80 × 60 mm ABS enclosure with every internal component mounted in place, plus a specification plaque in front. What it mates with Tap adapter for 15–24 mm taps, with a 20 mm ID / 28 mm OD / 3 mm silicone O-ring beneath it 6 mm OD / 4 mm ID PU tubing to 1/4" (6 mm) quick-connect fittings and a 12 V NC solenoid valve E18-D80NK IR sensor through an 18.5 mm bore in the front wall Inside the enclosure 50 × 40 mm control PCB and 35 × 25 mm SPET driver on standoffs with M3 screws 35 × 25 mm relay module and a 12 V power supply block Red wiring harness between boards, sensor, solenoid and power supply Floor tube clip and four lid screw bosses (M3 × 10 mm) Check before printing The lid sits beside the enclosure so the interior stays visible. The power supply is a 30 × 40 × 22 mm representative block, since no size was specified, so check it against your actual unit. The sensor bore suits an 18 mm body only. Other enclosure sizes are not covered.
Kabelhalter 3 Kabel für 25 mm Tisch
C-förmige Klemme für Tischplatten mit 25 mm Dicke. Der untere Arm hat drei offene Kabelschlitze, in denen Ladekabel senkrecht nach unten geführt werden. Das Teil liegt beim Drucken flach auf der Seite und braucht kein Stützmaterial. Maße Gesamtbreite: 36 mm Gesamthöhe: 37,5 mm Armlänge: 40 mm Spalt für Tischplatte: 25,5 mm Armstärke: 6 mm, Rückwand: 6 mm Kabelschlitze: 3 Stück, Ø 8 mm, Mittenabstand 12 mm, Öffnung 6 mm Kanten 1 mm gefast Druckhinweise Ausrichtung: auf die Breitseite legen (wie modelliert) Material: PETG oder PLA, 3 Wandlinien empfohlen
Arcade Console Desk Clock Case
A compact desk-clock enclosure with a gaming-rig attitude: chamfered shoulders, vented flanks and grooved front stripes under the OLED window, like a mini console from a late-night LAN party. Window for a 0.96" OLED on the front Standoffs for an ESP32 WROOM-32 devkit USB slot at the back Four corner screw bosses and a separate screw-on lid Side vent slots for airflow
Bracelet Link Fit Gauge Block
A bracelet repair print that turns out too tight or too loose wastes hours. This fit gauge block is a 15-minute test piece that checks the fork slot and pin bores before the real part gets printed. Key numbers Block: 14 x 32 x 6 mm, origin at center, 1.2 mm edge fillets Fork slot: 5.2 mm wide, 12 mm deep, open at the -Y end, flat end wall at Y = -4 Prongs: 4.4 mm wide each Bores: Ø1.6 along X at Y = -10 (through both prongs) and Y = +10 (solid section) Tongue sample: 4.4 x 4.6 mm, 8 mm long on the +Y end, 0.9 mm end fillets, Ø1.6 bore at Y = +19 (40 mm overall) Printing Flat on the bed, PLA or PETG, 0.4 mm nozzle, 0.2 mm layers 4+ walls, 100% infill, 3 mm brim, no supports, 40 mm/s or slower Ream both bores once by hand with a 1.5 mm drill bit Checks A bracelet tongue link should enter the slot with slight friction. An original pin should slide through the -Y bore.
Ten-Port Keystone Panel With Fan
A 270 × 61 mm mounting panel with a 60 mm fan opening on the left and ten snap-in keystone ports on the right. A rounded, squircle-style notch is cut into one long edge near the right end. Remix hooks Notch span: runs from 216.25 mm to 258 mm along X, 15.25 mm deep in Y. Move either end to resize it. Corner radius: both inner corners use a 7 mm radius. Raise it for a softer shape; keep it under about 7.6 mm to stay within the notch depth. Corner material: the notch stops at 258 mm, leaving the right-end 3.5 mm mounting hole (5 mm from the end) fully surrounded. Keystones: 14.5 × 16 mm openings with a 1.8 mm front lip and rear clip relief. Dimensions are provisional, so test one jack before printing all ten. Pairs with: a cable-management bar or a fan grille over the 58 mm vent. It's meant for a particular 12U rack.
Eiffelturm-Gitter auf Klemmring
Ein filigraner Gitterkorb auf vier nach innen geknickten Pfosten, die an eine Eiffelturm-Silhouette erinnern. Unten sitzt ein Klemmring für Zylinder mit 73 mm Durchmesser. Gesamthöhe ca. 54 mm Klemmring 12 mm hoch, mit Schlitz und M4-Querbohrung Vier Pfosten enden unten am Korb Korb aus Stäben und Ringen
Electronics Box With Solar Panel
A wildlife alert electronics box with a tilted solar panel on top, and no post or base to tip over. The box sits flat on the table, and its two front holes stay stacked on one centre line. Box: 110 × 70 × 60 mm, 3 mm walls, lid held by four screws Front holes: 5.2 mm amber LED above a 24 mm PIR sensor opening Solar panel: 110 × 100 mm at 30°, on two printed brackets Printing: FDM, no supports needed for the lid; print the box with its open back facing up
Watch Bracelet Mid-Link 14 x 31 mm
Replacement mid-link for a metal watch bracelet, 14 mm wide and 31 mm long, with a crowned top, a forked female hinge end and a single-tongue male hinge end. Pin holes are 1.6 mm for reaming. The underside is pocketed to save material. Body: 14.0 x 31.0 x 3.4 mm, 1.4 mm edge fillets Crown: raised 0.8 mm above the body top Female end: two 5.2 mm diameter ears, 5.2 mm slot Male end: 4.6 mm diameter tongue, 4.4 mm wide Pin holes: 1.6 mm, at Y = ±17.9 (35.8 mm pin to pin) Underside pocket: 1.9 mm deep, 0.7 mm corner radius Wrist curve not applied; exported flat Intended for PETG, printed bottom face down
Armoured Oyster Bracelet Mid-Link
A reinforced stand-in for a broken oyster-style solid link, with a crowned top and an R45 concave underside that follows the wrist. The hinge ends are built to take the load. Female end: two Ø5.2 ears around a 5.2 mm gap; male end: one Ø4.6 × 4.4 mm tongue. Ø1.6 pin bores, 35.8 mm pin to pin. Underside pocket stops 11 mm from centre, leaving solid hinge zones. Filleted webs where the ears meet the body. Ream the pin holes to 1.5 mm after printing.
Drehscheibe Neu
Zwei übereinanderliegende Scheiben (Ø75 mm, je 2 mm dick) mit Randzapfen, die sich gegeneinander drehen lassen. Der Zapfen sitzt an der unteren Scheibe, geht durch die obere und hat oben einen flachen Kopf, der die obere Scheibe hält. Untere Scheibe mit Ø30-mm-Mittelloch Zapfen Ø6 mm, 30 mm links der Mitte Loch in der oberen Scheibe Ø7 mm (0,5 mm Spiel pro Seite) Kopf Ø10 mm, 1,5 mm dick, 0,3 mm über der oberen Scheibe 0,3 mm Spalt zwischen den Scheiben, druckbar in einem Stück Obere Scheibe ist geschlossen, nur Drehbewegung
G1 1/4" BSPP Bull Nose Plug, Concave End
A male G1 1/4 BSPP threaded plug with a 50 mm hex head and a concave dish in the threaded end, made for a bull nose fitting with a female G1 1/4 port. Fit check Fits: female G1 1/4 BSPP ports (11 TPI, 2.309 mm pitch). Thread is cut at 41.5 mm against the 41.91 mm nominal for print clearance. Does not fit: NPT ports, metric ports, or male-threaded fittings (those need a female cap). Thread form: 60° flanks, not true 55° Whitworth. Fine for a plastic plug, not an exact BSP profile. Measure first: the internal thread diameter of the fitting. Dimensions Thread length 18 mm, hex head 50 mm across flats, 10 mm tall. Concave dish: about 32 mm across and 8 mm deep in the threaded end. No sealing washer face is included; use a bonded seal or thread tape.
Reifen mit offenem U-Profil innen
Ring mit Ø27,5 mm außen und Ø18,5 mm innen, 6 mm breit, mit nach innen offener U-Nut (4 mm breit). Der Nutgrund liegt bei Ø23,5 mm, damit die Wand am Außenumfang 2 mm stark bleibt. Remix-Ansätze Außendurchmesser (27,5 mm): Nutgrund mitführen, er sollte immer 4 mm unter dem Außendurchmesser liegen, um 2 mm Wand zu behalten. Nutbreite (4 mm): Bei 6 mm Gesamtbreite bleiben je 1 mm Flanke. Schmalere Nut oder größere Breite macht die Flanken stabiler. Innendurchmesser (18,5 mm): Bestimmt die Öffnung und damit, was der Ring aufnimmt. Kombiniert gut mit: Rollen, O-Ringen oder Gummiauflagen, die in der Nut sitzen.
StudyDock Desktop Phone Stand
What it's for A one-piece desktop phone stand for students, holding a phone at a 65° viewing angle on a desk. Dimensions 65 mm wide, 75 mm deep, 70 mm tall 4 mm flat base, 4–5 mm walls 14 mm deep shelf with a 6 mm front lip Two triangular side supports Remix ideas Widen the shelf for phones with cases. Add a cable slot through the backrest. Lower the backrest angle for typing-height viewing.
Posable Dragon With Friction Joints
A posable toy dragon that holds its pose, with detailing so it doesn't look like a plain chain of balls. The old version looked like a bare stick of linked beads. This one adds belly plates, scale studs and a trimmed base. What's on it Cream belly plates under each body link Dark-red scale studs along both flanks, plus the back spike row Raised gold trim around the edge of the base Same 12 ball-jointed body links and ball-jointed head Print notes 0.2 mm joint clearance: raise it if the joints fuse, lower it if they sag Print in PETG for repeated bending Multi-colour print or paint the belly plates, trim and spikes
Pad Plate — Offset Square Marker
Pad Plate is a flat base plate with a small raised square pad near one end, built as a clean surface for labels, stickers, or a colour swap. The pad is sized to sit comfortably on the plate and stays low enough to print cleanly in a few layers. Dimensions Plate: 28.5 × 40 × 3 mm Pad: 11 × 11 mm, 0.7 mm thick Pad position: centred in X, 2 mm in from the Y- edge Print notes 0.7 mm pad suits a 0.2 mm layer height at roughly 3 to 4 layers. Print flat, no supports needed. Pad and plate are separate colour regions, so a filament swap at the pad layer works well.
200 mm Pen with Compact RC Mount
A 200 mm display pen with an 11 mm round barrel, a tapered tip, a pocket clip and "HECTEC SONDEREN" engraved on the front. A small base plate with two cradles sits under the barrel near the tip end, for mounting the pen on an RC car. The pen is held in the cradles with zip ties, and the plate is fixed down with one central screw. Pen length: 200 mm, barrel diameter 11 mm Mount plate: 46 x 24 mm, located at the tip end of the barrel Two cradles with zip-tie slots beside each One 3.6 mm screw hole in the plate centre Solid barrel, display use only
Spider Web Plaque with GARTH Name
What it's for A flat spider web ornament with the name GARTH raised across its centre. Suitable for wall hanging, Halloween decor or a themed gift. Dimensions Web diameter: about 132 mm Thickness: 2 mm web, 4 mm with lettering 12 spokes, 4 concentric rings, hanging loop at top Lettering: 10 mm size, Permanent Marker font Remix ideas Swap the name or change the font Add a plush spider on a ring Scale down for a keychain or ornament
T-Rex Holding LUKE Sign
A standing T-rex on a flat base, gripping a name sign that reads LUKE in raised lettering. Prints as one piece, sign facing front. Remix hooks Name: swap "LUKE" for any short name; keep the sign about 60 mm wide, or widen it for longer names. Font and size: Luckiest Guy at size 12 fills the 60 x 22 mm sign; drop the size if the name grows. Base: 70 x 100 x 3 mm, easy to enlarge or turn into a keychain-sized stand. Colour split: base, dino and sign are separate regions, ready for multicolour prints. Pairs with: a desk shelf, or a row of dinos with different names.
Need a part that doesn't exist yet?
Start building →