3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
kraancakehouder 35/25/15 totaal
Caketoren met drie schijven en een vakwerkkraan met vierkante voet van 50 mm. Wat past waar Onderste plaat (Ø350 mm): vier kwarten met een opstaand vierkant middenblok. Samen vormen ze een zitting van 30,6 mm vierkant, 8,6 mm diep. Kraanmast 1: heeft een vierkante voet van 30 mm met vier klikbolletjes. Die klikt in de zitting. Middelste en bovenste plaat (Ø250 en Ø150 mm): een rond centrumgat van Ø16 mm voor de kraan. Platen: kwarten verbonden met losse pennen Ø6 mm. Controleer voor het printen Meet de voet van mast 1 na. Die moet 30 mm zijn, tegenover een zitting van 30,6 mm. Past niet op een bed kleiner dan 300×300 mm.
Balance Coffee Raised Letter Sign
A flat rectangular sign with raised "BALANCE COFFEE" lettering in Archivo Black, sized for a shelf, counter or wall. Remix hooks Plate size: 140 × 40 × 4 mm with a 1 mm chamfer. Widen it for a longer sign, or stack the two words on two lines and make the plate taller. Letter height: 2 mm raise, text size 11. Go to 1 mm for a quicker print, or 3 mm for stronger shadows. Colours: the plate and letters are separate regions. Print with a filament swap at layer 4 mm for a two-tone sign. Mounting: no holes yet. Add two screw holes near the ends, or a rear slot for hanging. Pairs with: a small stand or a wall bracket.
Ember Drake Charizard Mini Figure
A miniature Charizard collectible with a smooth rounded head, snout, small horns and green eyes, plus a cream belly that follows the curve of the torso. Two broad blue-green wings sit on the upper back, and a long tapering tail curves up to a red-and-yellow flame. Design notes Wings, arms and tail sit on captive ball joints with 0.35 mm clearance, so they can swivel after printing. Legs and feet are fixed to the body, which gives the figure a stable stance. Wing membranes are 2.4 mm thick with rounded edges. Colour regions: orange body, cream belly, teal wings, green eyes, red flame with a yellow core.
Snake Tail Phone Stand
A one-piece orange phone stand with a low front lip, a short flat seat and a backrest leaning up to about 60 mm. A zig-zag snake of humps runs along the back. Remix hooks Lip height: the front stopper is about 5 mm of strip plus the strip's rounded end, roughly 7.5 mm in total. Raise it for a more secure hold, or lower it further to keep captions clear. Seat depth: 12 mm. Deepen it for thick cases, though a steeper backrest helps more. Backrest angle and height: it rises about 18 mm in Y over 55 mm in Z, so it is steep. Both are easy to change. Snake humps: 4 peaks, each about 14 mm high. Add more humps, or raise or lower the peaks. Width: 70 mm, with a 5 mm strip thickness. Pairs well with a non-slip pad on the seat.
Minecraft Grass Block Keychain
What it's for A keychain shaped like a Minecraft grass block: smooth brown dirt body, green grass cap that overhangs slightly, and blunt, irregular grass drips on all four sides. A sturdy corner loop takes a key ring. Dimensions Approx. 27 × 27 × 28 mm Cap about 5 mm thick; drips 3.5–8 mm long Loop hole about 4 mm, at one top corner Remix ideas Swap colours for mycelium or snow blocks Change drip layout Enlarge the loop hole for a lanyard
Tape Spindle and Zip Tie Bench Caddy
Bench caddy that keeps a tape roll and a bundle of zip ties in one fixed spot on the bench. A 24 mm spindle holds a roll with a 25 mm core. A serrated tear bar runs along the front edge so tape can be pulled across the teeth and torn. A block on the right has three slots for zip ties up to 90 mm long. Specs Base: 150 × 100 × 5 mm plate with 1.5 mm chamfered edges Spindle: 24 mm diameter, about 46 mm tall, with a 34 mm foot and a 30 mm top flange. Sized for a 25 mm core with 1 mm clearance. Tear bar: 70 mm long, 4 mm thick wall with 14 serrated teeth. It sits along the front (-Y) edge, beside the spindle. Tie trough: 34 × 100 mm block, 28 mm tall, with three 6 mm wide slots, each 90 mm long, in a row across X. Overall height: about 54 mm, measured at the top of the spindle flange. Material: PLA or PETG. Print flat on the base with no supports. Notes Fit has not been tested against a physical roll. If the roll is tight on the spindle, reduce the spindle diameter slightly. Slot width suits standard narrow zip ties. Wider ties need wider slots.
Fan and Keystone Mounting Plate
A 270 x 61 mm flat plate, 4 mm thick, combining a 60 mm fan mount with a row of ten keystone jack openings. The fan opening sits at the left end with four screw holes on the standard 50 mm spacing. The right side carries ten rectangular openings on an 18 mm pitch for standard keystone jacks. A 3.5 mm mounting hole sits 5 mm from each end on the centerline. Plate: 270 x 61 x 4 mm Fan: 56 mm opening, 4.3 mm screw holes at 50 mm spacing Keystones: 10 openings, 14.8 x 19.8 mm Mounting: 2 x 3.5 mm holes
Sleeve — 0.385" OD Spacer Tube
Sleeve is a plain, precise hollow cylinder sized in inches: a straight-through bore and a clean outer wall, ready to use as a spacer, bushing or standoff. Dimensions Outer diameter: 0.385" (9.78 mm) Inner diameter: 0.26" (6.60 mm) Length: 0.75" (19.05 mm) Wall thickness: about 0.0625" (1.59 mm) Print notes Print standing on end, no supports needed. Bore may print slightly tight; ream or scale up a touch if fit matters.
Two-Piece Gridfinity Caliper Box
A 6 x 3 unit Gridfinity caliper box split at the middle into two halves, each about 126 x 126 x 25.4 mm, so each fits a 150 mm print bed. Two dovetail keys join the halves. The stepped pocket holds a 9.25 in caliper: a 15.9 mm body slot and a 78 x 97.5 mm head recess, both 12.7 mm deep. The stacking lip and finger scoops are kept. Remix hooks Split position: the cut is at X = 0, on a Gridfinity cell boundary. Moving it in whole 42 mm steps keeps the cells intact. Dovetail size: 8 mm at the root, 13 mm at the tip, 16 mm tall, at Y = ±35. The socket has 0.25 mm clearance. Loosen or tighten it to suit your printer. Joint type: swap the dovetails for round pins or add glue grooves. Pairs with: other Gridfinity bins on a 42 mm baseplate.
Extruder Figure on Cloud Plate
A printable extruder-style character lying on its back, standing in front of a solid 2 mm cloud plate. The name "Printytron" is raised on the body below the screen and is a separate part, so it can be coloured on its own. Boxy body with a recessed magenta screen showing a face with curved eyebrows and pupil indents Curved arms, thick hands, side box with teal button Hexagonal nozzle with a chunky square collar, flat on the plate Raised Space Mono lettering in its own colour Cloud backing plate whose bottom edge lines up with the hands and nozzle so the print can stand on a desk
75 mm Drehscheibe, Randzapfen, Mittelloch 30 mm
Zwei übereinanderliegende Drehscheiben mit je 75 mm Durchmesser, verbunden über einen Zapfen am Rand (8 mm Schaft, 14 mm Kopf, 28 mm von der Mitte). Der Zapfen ist mit einem roten Punkt markiert. Maße, die vor dem Druck zu prüfen sind Lochdurchmesser in der unteren Scheibe: 30 mm, mittig, durchgehend durch 4 mm Material Spiel zwischen Zapfen (8 mm) und oberer Scheibe (9 mm Bohrung): 0,5 mm Abstand Lochrand zu Zapfenkopf: ca. 6 mm Hinweise Die obere Scheibe ist über dem Loch geschlossen. Die Scheiben liegen nur 0,5 mm überlappend aufeinander und können beim Druck verkleben, wenn das Spiel zu knapp ausfällt. Nicht für Zapfen-Verschiebung außerhalb des 28-mm-Radius ausgelegt.
Drehscheibe
Zweiteiliger Aufbau: eine Klebeplatte mit Achse nahe am Rand und eine darüber drehbare Scheibe, beide Ø74 mm. Die Scheibe schwenkt um die außermittige Achse und hat am gegenüberliegenden Rand einen gebogenen Schlitz. Remix-Ansatzpunkte Durchmesser: 74 mm, lässt sich für beide Teile gemeinsam ändern. Achsposition: 26 mm aus der Mitte. Weiter außen lässt weniger Wand um das Senkloch. Schlitz: 6 mm breit, etwa 60° Bogen, ca. 2,5 mm Wand zum Rand. Länge über den Winkel anpassbar (z. B. 90° oder 120°). Loch in der Klebeplatte: Ø8 mm, 27 mm vom linken Rand (Blick von unten), 2 mm über der Mitte. Passt für Schraube oder Senkung. Spiel: 0,4 mm zwischen Platte und Scheibe, für andere Drucker anpassbar.
Fidget Spinner Planetario Ø70 mm
Fidget spinner a ingranaggi planetari stampabile in un solo pezzo (print-in-place), diametro esterno 70 mm, con ingranaggio solare centrale, 5 satelliti e anello esterno dentato internamente. L'anello è alleggerito da 10 fori passanti e non ha coperchi, così gli ingranaggi restano visibili. Diametro esterno: 70 mm, spessore 8 mm Modulo 1,5; solare 15 denti, satelliti 10 denti, corona 35 denti Denti elicoidali a spina di pesce (25°) che trattengono i satelliti senza assi Gioco sui denti: 0,25 mm Fori centrali Ø7 mm (solare) e Ø5 mm (satelliti) per alleggerire Stampa piatta, senza supporti; PLA o PETG
16 mm Ball Track with Support Post
A 350 mm ball track (250 mm slope at 17.5° plus 100 mm flat) with a matching target ball support post for a 16 mm ball. Fit Track: 24 mm wide, 17.5 mm U-groove, 16 mm ball. Post: 24 mm base, 9 mm rod, 22 mm tall, flaring to a 20 mm head. Seat: 16.5 mm diameter, 3.5 mm deep spherical pit. Post axis sits so the ball-to-ball gap from the groove end is about 12.5 mm. Check before printing Measure your ball. The seat is sized for 16 mm and will not suit balls much larger or smaller. Known incompatibilities The post is a separate part that sits on the table. Its ball centre sits higher than the ball centre at the groove exit, so shim the track up or trim the post height to match.
Antalya Kebap Untersetzer 3.0
Runder Getränkeuntersetzer im Kebap-Stand-Look: Die Schrift ANTALYA KEBAP II steht 1 mm erhaben auf einer glatten Fläche, umgeben von einem hohen Rand, der Kondenswasser und Verschüttetes im Zaum hält. Durchmesser 100 mm, Boden 5 mm stark Umlaufender Rand bis 6 mm Höhe Schrift 1 mm erhaben, Bebas Neue Die Schrift endet auf Randhöhe, daher bleibt oben alles bündig
Plate With Offset Square Pad
A flat 28.5 × 40 × 3 mm plate with an 11 × 11 mm raised square pad, 0.5 mm thick, centered in X and set 2 mm from the Y- edge. Remix hooks Pad thickness (0.5 mm): a multiple of your layer height keeps the pad clean. 0.5 mm is about 2 or 3 layers. Pad offset (2 mm from the Y- edge): move it along Y to centre it or push it to the other edge. Plate length (40 mm): the pad is 11 mm, so any length above roughly 15 mm still holds it. Pairs with: a label, a sticker, or a second pad in a different colour for a multi-colour swap.
Figure8 — Clip-On Cord Winder
Figure8 is a compact cord winder that snaps onto the flex of a kettle, toaster or similar appliance and takes up the slack. Wrap the spare cord around the two end horns in a figure-eight pattern, and the curled horn tips hold the turns in place so the wrapped cord can't spring loose. It is designed for cluttered counters where appliance cords tend to tangle. The spine carries a round channel with a narrower snap-in slot, so the winder stays on the cord instead of sliding off. The cord is pressed through the slot, and the lips flex to let it pass. Dimensions Overall length: 80 mm Overall width: about 46 mm across the horns Height: 9 mm Cord channel: 5 mm diameter, running the full spine Snap-in slot: 4 mm opening Features Four horns with tips curled back toward the centre Chamfered spine edges Single-piece body with no assembly Compatibility Intended for standard 6–7 mm appliance cords, which squeeze through the slot and sit snugly in the channel Print notes PETG or TPU is recommended, since the slot lips need to flex Stiff PLA may crack at the lips when the cord is pushed in Prints flat on the bed; the curled tips are short, so supports are only needed if the slicer flags them
Obsidian — Ribbed Can Cooler with Handle
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports. Dimensions Inside diameter: 68 mm Inside height: 105 mm (above a 3 mm base) Wall: 2 mm, base: 3 mm Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel Features Diagonal ribs outside, perfectly smooth bore inside Rounded top rim Broad, rounded handle, 24 mm wide Flat front panel, 40 × 66 mm Print notes Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers No supports expected; fits a 180 mm build volume
Welcome — Cursive Neon Strip Holder
Welcome is a script-lettered sign form with an open channel running through every letter, built for pressing flexible LED neon strip into place. Fill the channel, wire it up, and the flowing lettering glows like a custom neon sign. Features Heavy brush-style "Welcome" lettering 1.6 mm walls around an open top channel 2 mm floor, 10 mm overall height Wire exit holes through the floor at the ends of the word Print notes Prints flat with no supports Strip width varies by brand, so check the channel width against your strip first
3.2 mm Jump Ring Georgie Letter Links
Seven individual letter links spelling G-e-o-r-g-i-e, made to be joined by metal jump rings into a name bracelet. Fitment Each link is a 14 × 14 mm plate, 3 mm thick, with the letter raised 1.5 mm in Luckiest Guy. A 3.2 mm hole runs front to back through a round tab on each side, so a ring passes through the flat face. Hole centres are 19 mm apart on each link; adjacent links join with one jump ring through facing holes. Check before printing Jump ring wire must be under about 3 mm, or the holes will not take it. Does not fit Rings with wire thicker than 3 mm, or links with a closed clasp-style bail.
14 x 14 x 13 mm Palm Cavity Hand
A stylised hand with the middle finger extended and the other fingers folded, with a square 14 × 14 mm cavity, 13 mm deep, centred in the palm. Fit and check Cavity: 14 × 14 mm opening, 13 mm deep, open on the palm side, blind (does not exit the back of the hand). Palm is 22 mm thick, leaving about 9 mm of material behind the cavity floor. Measure the cavity after printing if a 14 mm part must fit; FDM usually shrinks holes slightly. Not included No reference image was available, so proportions are generic. Fingernail is a small raised plate on the back of the middle finger. It does not show from the palm side. Scaled compact, about 104 mm tall, so it is not life-size.
Hoof Evener Thumb Ring 1.2
A low-profile thumb ring designed to index a farrier's hoof-evener ruler. 1/8" Slim Ring: Keeps bulk out of the way while holding the thumb perfectly on zero. D-Profile Peg: The 6mm mounting peg is shaved flat on the back, allowing the entire model to print dead-flat on the bed without any supports. Flex Slit: Open front ensures it can comfortably accommodate varying thumb sizes.
Farrier Hoof Evener Ruler V 1.12
A print-ready pair of hoof evener rulers, 6-inch and 8-inch, with four marker assemblies laid out on the same plate. Each ruler has an open viewing window, a solid center bridge, raised tick marks on the inside of each rail and numbers on the outside. A 3.5 mm hole at dead center takes a slim flexible ring. Scales end exactly at 6 and 8 inches, with extra length at each end for the sliders to reach 0 and the end mark Two sliders per ruler, so each end can hold a marker Each slider has a thin blade foot, a round peg with an M2 pilot hole and an arrow cap with a small notch to see the hoof edge Domed pins on the foot click into hidden dimples under the ruler at each quarter inch Printed flat, no supports needed for the rulers
Need a part that doesn't exist yet?
Start building →