3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Hex Tube 40 mm Tall With Center Bore
A hex tube, 4 cm tall, for when a round spacer or standoff spins or rolls where a flat-sided one would hold still. The 2.5 mm bore runs the full length so a rod, wire or screw passes straight through. Key dimensions Height: 40 mm Width: 5.15 mm point to point Center bore: 2.5 mm diameter, through the full length Printing Print standing upright, no supports needed. Walls are thin at the hex flats, so use at least 2 perimeters and a small nozzle if possible.
Under-Sink Bag Roll Dispenser Barrel
A grocery-store bag-roll dispenser, shrunk down and bolted under the sink. A snug barrel holds a 60 mm roll of trash bags, and the next bag's edge hangs out of a slot in the bottom, ready to grab. A serrated lip along the front of the slot tears each bag off cleanly, so there's no more digging for the end of the roll. The barrel is closed at one end and open at the other. A separate press-fit end cap seals the open end once the roll is loaded. Design notes Bore: 64 mm diameter for a 60 mm roll, with 3 mm walls. Length: 130 mm overall. Dispensing slot: 20 mm wide, running along the bottom of the barrel. Tear lip: a row of downward-pointing teeth at 4 mm pitch on the front edge of the slot. Mounting: a flat back plate with two countersunk screw holes. The holes sit above the barrel, so screws never cross the bore. End cap: printed as its own piece, with a plug that fits the bore and a flange that matches the barrel. Print and remix notes The teeth are the lowest points as modelled, so plan on supports under the barrel. Printing the part on its back plate is an easy re-orientation. Slot length, tooth pitch and screw spacing are the obvious values to adjust for other roll sizes or cabinet layouts.
Round Water Bottle With Cap
A round water bottle with a tapered shoulder, a 24 mm mouth and a separate slip-on cap. Printed as a hollow vessel with 3 mm walls. Remix hooks Body diameter and height: 70 mm wide, 170 mm straight section. Change these to resize capacity. Wall thickness: 3 mm. Raise it for watertight prints in PLA, or lower it with vase mode in mind. Neck: 24 mm bore, 30 mm outside. Swap the plain cap for a threaded one using a threaded rod and nut. Pairs with: a silicone gasket, a carry loop through the neck ring, or a sleeve that fits the 70 mm body. The cap is a friction fit and not a sealed closure. Test before filling.
Pumpkin Phantom Witch Hat Figurine
A friendly ghost rising from a jack-o'-lantern, topped with a chunky witch hat. A 70 mm single-piece figurine with a flat base and no fragile tips. Remix hooks Hat height: the cone is two stacked segments (10 mm and 8 mm); stretch them for a taller hat. Brim: 36 mm wide, 3 mm thick. Widen it, but add support beyond about 40 mm. Face: carved triangle eyes and a rectangular mouth on the pumpkin; swap in a toothy grin. Ghost arms: simple 8 mm round nubs. Lengthen them into waving arms. Pairs with: a round display plinth, or a tealight-sized base for a lamp variant.
Caregiver Check Station Enclosure, Gray and Red
A caregiver check-in box with no obvious place to tap, and a back panel that fights you at every repair. This enclosure puts a large red TAP HERE panel on the front and a screw-on back cover behind it, so the electronics come out without disturbing the front. Size: 150 × 110 × 36 mm body, with a 3 mm back cover. NFC panel: 64 × 64 × 2 mm red panel, replaceable, behind a 1.5 mm lip. It is held by a separate holder with four M2.5 screws. Back cover: four M3 × 12 screws into body posts, with a 0.3 mm clearance skirt. Two keyhole slots handle wall mounting. Openings: PIR window 23 mm, three 5 mm LED holes (green, yellow, red), BME280 air slots, 12 × 6.5 mm USB-C slot, 5 mm reed-switch cable hole, and top and bottom vent slots. Printing: body and panel face-down, cover outside-down. PLA, no supports, 3 walls, about 15% infill. Not final: every board position is a placeholder. Measure the ESP32, PN532, PIR and BME280 before fixing the internal layout.
Printytron Extruder Figure, 85 mm Wide
Desk figure of the Printytron character, styled after an extruder. It prints lying on its back, so the whole underside sits flat on the plate and no supports are needed. The body has a recessed magenta screen with a face (eyes with pupil indents, curved eyebrows, smile), a teal button on a side box, curved arms ending in round hands, and a hexagonal tapered nozzle on a square collar. "Printy.dev" is engraved below the screen. Specs Overall size: about 85 mm wide, 76 mm long, 15.5 mm tall as printed Orientation: back face down, screen facing up Body thickness: 14 mm; arms 5 mm thick; hands 10 mm thick Side box: sloped underside (about 50° from the plate) so it prints without supports Antennae: run down to the back face, so they print flat Nozzle: hexagonal cone with a flat underside along its full length, on a 22 mm square collar with a 1 mm bottom chamfer Engraving: "Printy" at 8 mm and ".dev" at 4 mm, Space Mono, about 1 mm deep Colours: yellow body, magenta screen, teal button; suited to a multicolour print or painting after printing
Sliding AMS 2 Pro Riser with Tabs
A riser for the top of a Bambu X2D that holds an AMS 2 Pro on a tray and slides it forward on two drawer slides for loading and unloading. The tray has four upright locking tabs that engage the holes under the AMS. Tab outer edges are 355 mm apart in X and 232 mm apart in Y. Each tab is 11 mm thick and 30 mm tall. Overall footprint about 380 × 310 mm, inside the X2D's 392 × 406 mm top 2 × 300 mm side-mount ball-bearing drawer slides, 12.7 mm wide M4 heat-set inserts and M4 screws for slides and crossbars Frame, rails and crossbars print as separate parts
Tabletop Wildlife Alert, 100 mm Diamond Sign
Modular tabletop wildlife-warning prototype printed as separate parts that bolt together: base, three pole sections, four brackets, electronics enclosure with lid, PIR sensor housing with rain hood and lid, amber light housing with lid, and a diamond sign reading WILDLIFE CROSSING with no graphic. The stack runs bottom to top: electronics enclosure, PIR sensor facing forward, two amber LED openings, then the sign. Each housing screws to its own bracket, and each bracket clamps onto the pole with one cross-screw. Dimensions (mm, outside) Electronics enclosure: 70 × 60 × 50, interior about 65 × 57 × 45, with lid PIR housing: 60 × 40 × 35, 23 mm lens opening, rain hood, with lid Light housing: 70 × 35 × 30, two 8 mm LED openings, with lid Sign: diamond 100 point to point, 3 mm thick Base: 100 × 84 × 6 Pole: three sections, 20 × 20 × 58 Overall height: about 224 To confirm before printing Controller board size (a full Uno will not fit the interior) PIR lens diameter and LED diameter (23 mm and 8 mm are placeholders) Printer build area Electronics are untested
Tabletop Wildlife Alert, 100 mm Diamond Sign
Modular tabletop wildlife-warning prototype printed as separate parts that bolt together: base, three pole sections, four brackets, electronics enclosure with lid, PIR sensor housing with rain hood and lid, amber light housing with lid, and a diamond sign reading WILDLIFE CROSSING with no graphic. The stack runs bottom to top: electronics enclosure, PIR sensor facing forward, two amber LED openings, then the sign. Each housing screws to its own bracket, and each bracket clamps onto the pole with one cross-screw. Dimensions (mm, outside) Electronics enclosure: 70 × 60 × 50, interior about 65 × 57 × 45, with lid PIR housing: 60 × 40 × 35, 23 mm lens opening, rain hood, with lid Light housing: 70 × 35 × 30, two 8 mm LED openings, with lid Sign: diamond 100 point to point, 3 mm thick Base: 100 × 84 × 6 Pole: three sections, 20 × 20 × 58 Overall height: about 224 To confirm before printing Controller board size (a full Uno will not fit the interior) PIR lens diameter and LED diameter (23 mm and 8 mm are placeholders) Printer build area Electronics are untested
Hex-Embossed Storage Tub
This storage pot brings an industrial, sci-fi crate aesthetic to the workshop or pantry desk. The model measures exactly 145mm wide, 200mm long, and 100mm deep on the inside, leaving plenty of room to slot in boxed goods or bulk packaging. Design Notes Textured Shell: The outer walls feature a debossed hex-grid pattern that improves grip without compromising wall strength. Grip Handles: Both ends feature pill-shaped cutouts scaled for easy lifting, whether it's on a high shelf or tucked under a bench. Rounded Profile: Corners are filleted inside and out, making the tub easy to wipe down.
Clicker Fidget Keycaps A–Z, Heart, Star, Flower
Loose keycaps for clicker fidget toys: no more generic blank caps when a custom letter or symbol is wanted. Each cap is a separate 18 × 18 mm square with rounded corners and a hollow underside, with a bold red legend inlaid into a white top. Set: letters A–Z plus heart, star and flower (29 caps) Size: 18 × 18 mm, 9 mm tall Stem: MX-style cross socket, 4.1 × 1.35 mm arms Legend: bold, centered, inlaid 0.8 mm into the top Print: top face up, no supports needed for the caps; use white and red filament (or a pause for the colour change) Keys are spaced apart on the plate and not joined; split into individual files in the slicer
HexCatch — Geometric Coaster
Introducing HexCatch, a 90mm circular coaster engineered to keep surfaces perfectly dry. The surface features a recessed, concentric hexagon pattern that acts as a condensation trap, drawing moisture away from the base of glassware before it can pool and run onto the table. \n\n## Dimensions\n Overall footprint: 90mm diameter\n Thickness: 5mm \n Channels: 2mm wide and 1mm deep\n\n## Features\n Integrated drip reservoir: Geometric recesses hold condensation safely off the table.\n Modern profile: A clean circular exterior contrasts with the sharp hexagonal interior.\n Chamfered base: Slight angle on the bottom edge makes it easy to lift from flat surfaces.
Cartoon Cloud MagSafe Stand
A heavy, volumetric desktop stand for the iPhone 15 with a friction-fit MagSafe socket. The body is built as a fully rounded, bubbling cloud with a perfectly sheared flat front to carry the phone and a sliced flat bottom for desk stability. Mounted on a heavy, hidden pill base holding a 20-degree back-tilt. Fit: 56.5 mm cutout for a standard MagSafe puck, with an 8 mm channel for the cable routing down the face. Format: Two-piece assembly. The cloud and the base print separately and socket together. Volume: Bubbly 3D geometry across the back and sides; dead flat front surface for phone rest.
Heart Plaque With Levy and Leny
A heart-shaped plaque with two raised names, "Levy" on the upper line and "Leny" directly below it. The names are raised so they can be read by sight and by touch, and nothing else is written on the piece. Print details Heart footprint: about 85 × 78 mm Total height: about 10.3 mm (9 mm stepped, domed body plus 1.3 mm of lettering standing proud) Lettering: raised, printed as one piece with the heart Print flat, base down, with no supports needed Two colours are possible with a filament change at the lettering layer
Linked 20mm Compliant Clips
A pair of opposed 20mm compliant U-clips joined by a 40mm flexible meander strap. The part prints flat as a single monolithic body, using the thin 1.2mm wavy cord as a flexible tether and the thicker clip walls as rigid springs. Overall Footprint: 80mm long x 8mm wide x 8mm tall Clip Tolerance: 1.5mm resting gap, narrowing to 1mm at the front pinch points Tether Geometry: 1.5mm continuous meander, 40mm span Print Strategy: Prints flat on the bed; no supports required
Linked 20mm Compliant Clips
A pair of opposed 20mm compliant U-clips joined by a 40mm flexible meander strap. The part prints flat as a single monolithic body, using the thin 1.2mm wavy cord as a flexible tether and the thicker clip walls as rigid springs. Overall Footprint: 80mm long x 8mm wide x 8mm tall Clip Tolerance: 1.5mm resting gap, narrowing to 1mm at the front pinch points Tether Geometry: 1.5mm continuous meander, 40mm span Print Strategy: Prints flat on the bed; no supports required
Caixa 120x120x50 mm Estação Meteorológica
Caixa quadrada de 120 × 120 × 50 mm com paredes de 2 mm e tampa separada, fixada por quatro parafusos M3 nos cantos. Possui abertura para display, chave gangorra, entrada USB-C e fendas de ventilação, além de duas fendas para alça na parte superior da lateral. Parafusos: 4 colunas de canto, furo de 2,8 mm na base e 3,4 mm com escareado na tampa Display: abertura de 24,4 × 14,4 mm na tampa Chave gangorra: abertura de 15,3 × 10,3 mm na tampa USB-C: abertura de 9 × 4 mm na lateral +X Alça: duas fendas de 16 × 4 mm no alto da parede +Y, a 30 mm do centro para cada lado Ventilação: fendas nas laterais, longe das colunas, com fendas extras na região dos sensores Protoboard: dois trilhos baixos no fundo como guia provisório Impressão: base e tampa separadas, sem suportes necessários
69 mm Round Spacer, 5 Holes
A round spacer 69 mm in diameter and 10 mm tall with a 40 mm center bore and five 5.5 mm through-holes on a 54 mm bolt circle. Outer diameter: 69 mm Height: 10 mm Center hole: 40 mm Bolt holes: 5 × 5.5 mm on a 54 mm circle Hole spacing: 68°, 72°, 72°, 68°, 80° (the 80° gap is between the last and first hole) Prints flat with no supports
Four-Deck UNO Vault With Cap
A card-table caddy for four UNO variants: Classic, No Mercy, All Wild and Flip. Each deck lies flat in its own slot, split by 2 mm dividers, and a slip-over cap closes the box so nothing shuffles between slots. Slots sized from the supplied card dimensions plus clearance Walls 54 mm tall, so the tallest deck stays below the rim Finger hole through the floor of each slot to push decks up Front scoops for gripping Cap prints upside down and fits snugly over the outside of the rim
Stackable 20° Tilt Stand, Print Twice
A single 160 mm cylindrical half, cut on a 20° plane, that is printed twice. One piece alone holds a 120 mm cylinder tilted 20°. Two pieces, one flipped onto the other, stack into a straight block. Quantity: print 2 identical pieces. Seat: 124 mm diameter, 10 mm deep, on the tilted face. Lip: 175° arc, 7 mm thick, 15 mm tall, radius 62 to 69 mm. Step: 185° arc with 1.5 mm clearance per side and a 3 mm chamfered edge. Handles: three 30 mm finger scoops, 3 mm deep. Fit: slip fit, no snap. Bed size: at least 160 mm.
Script Plaque Planter Pot
A sturdy, functional planter featuring a prominent top rim and built-in bottom drainage. The outer face is permanently marked with custom lettering set directly into the curvature of the main body, ensuring the script perfectly traces the cylinder. Drainage: Five distinct bottom holes prevent water pooling Structure: Thick walls and a reinforced lip for easy handling Engraving: Carved to a uniform, shallow depth across the curved face
Print-in-Place Concentric Rings
A set of five concentric rings designed to print in place as a single piece. Excellent as a clearance test for your printer or just a satisfying desk fidget. Remix Hooks This design is built on a few key parameters that are begging to be tweaked depending on what you want to use it for: Wall Thickness: Currently set to 2mm for a solid feel. Clearance: Set to 0.4mm gap between rings. If your printer is finely tuned, drop this to 0.2mm or 0.3mm for tighter tolerances. Height: Currently 8mm, but you can scale this up on the Z-axis to turn them into nesting tubes. Inner Diameter: Starts exactly at 25mm to fit over standard dowels or large fingers.
Need a part that doesn't exist yet?
Start building →