3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Zahnbürstendose Zahnheld
Elektrische Zahnbürsten rutschen samt Ladestation bei der kleinsten Berührung vom Waschbecken. Diese Box umschließt Basis und Bürste und zwingt sie in eine stabile Position. Das Ladekabel wird flach am Boden nach hinten abgeführt, der Klappdeckel rastet über einen einfachen Klickverschluss ein. Druck und Maße: Scharnier: 3.2 mm Bohrung. Zum Verbinden wird eine M3-Schraube oder ein Stück 1.75 mm Filament durchgesteckt. Toleranz: 0.4 mm ringsum, damit die Komponenten sauber gleiten. Druckbett: Der Deckel liegt kopfüber, sein Scharniergelenk ist bereits so abgeflacht, dass es ohne Support auf der Platte haftet.
Onewheel Trunk Cradle
A thirty-pound wheel rolling freely in the back of a moving car is a problem that solves itself by smashing your groceries. This cradle stops the board from tipping and sliding on every sharp turn. Footprint: 180mm wide by 160mm deep — fits cleanly on most printer beds. Fit: The 290mm curve holds XR and GT tires perfectly, and Pints will seat securely against the slopes. Anchors: Features four 5.5mm countersunk holes for bolting directly to a cargo floor or wood base, plus two side channels for hooking a standard bungee cord over the tire. Printing: Needs a decent amount of infill (15-20% minimum) to handle the board's weight. No supports required.
Onewheel Charger Port Plug
Mud, sand, and metallic dust have a habit of finding their way straight into the exposed charge port, packing it solid until the charger refuses to seat properly. This plug seals the port to stop the debris before it becomes a problem. Fit and Printing Insert Diameter: 15.3mm, designed to friction-fit a standard Onewheel XLR charge port. Alignment: Features a 2.5mm keyway rib to match the port's orientation slot. Removal: Includes an extended tab with a 3.5mm hole for a lanyard, making it easy to yank out even with gloves on. Material: Print this in TPU (flexible filament) for a watertight seal and best friction fit, though PETG will work if your printer's tolerances are dialed in.
Ancient Duelist: Free Bounce
A 3D-printable proxy dueling card for house games. This layout trades out standard monsters for a red cup bounce shot, leaving the description box filled with scaled-up, illegible hieroglyphs. Card Details Title: Free Bounce Art: Single bounce path into a table cup Text: Ancient mystery symbols (house rules apply) Printing: Raised features across a multi-depth plate, perfect for color swaps on the top layers.
Supporto iPhone
Un supporto iPhone che si stringe con degli elastici per capelli e dietro dove ci saranno gli elastici deve esserci anche un attacco vesa lo standard più piccolo
12mm Schranktür Handtuchhalter
Ein robuster Handtuchhalter, der exakt über eine 12mm starke Schranktür greift. Konstruiert als flach liegendes Profil, um die Schichten entlang der Belastungsrichtung zu orientieren – das verhindert ein Brechen unter Gewicht. Ansatzpunkte für eigene Anpassungen Das Design ist bewusst simpel gehalten, um es schnell an andere Gegebenheiten anpassen zu können: Die Türstärke (12mm): Ist der Kern der Konstruktion. Aktuell sind 0.6mm Luft (Clearance) eingerechnet, damit der Halter gut aufgesteckt werden kann, ohne den Lack der Tür zu zerkratzen. Die Haken-Ausladung (22mm): Ausreichend für ein gefaltetes Handtuch oder einen Waschlappen. Wer dicke Badetücher aufhängen will, kann diesen Wert problemlos erhöhen. Die Breite (25mm): Gibt dem Halter Stabilität gegen seitliches Verrutschen auf der Türkante. Lässt sich ohne Stützstruktur drucken. Ideal für Küche oder Bad.
Flexure-Action Piano Octave
A single-octave, print-in-place keyboard array. Built on a common back-rail using living hinges, allowing each key to travel independently when pressed. Specifications Action: 1.0mm flexure (living hinge) Clearances: 0.6mm gap between neighboring keycaps Dimensions: Standard octave proportioning, miniaturized for rapid printing Material Note: Requires PETG or a reasonably ductile PLA to prevent flexure snapping after repeated cycles.
Pegboard Utility Knife Holder
A drop-in holder built for standard utility and carpet knives, mounting flush to small-pitch pegboards. A generous front thumb cutout makes retrieval quick, while the three-peg top row distributes the weight. Form & Fit Internal Clearance: Sized at 40x20mm internally to comfortably swallow standard sliding break-off blades. Board Specs: Engineered specifically for 12mm center-to-center grids with 4mm holes. Pegs are 3.6mm to provide an easy slip-fit. Drop Spacing: The lower stabilizing bumpers sit exactly 36mm (three 12mm increments) below the main hooks to align with the board's grid. Orientation: Best printed upright. The 45-degree angle on the hooks easily clears standard overhang rules without supports.
M2 Slotted GO 3S Mount
Fixed-angle TPU sleeve for the standalone Insta360 GO 3S camera, geared for flat-top drone frames like the AOS series. The Fit: Holds the bare GO 3 / GO 3S camera unit only (not the Action Pod). The Mount: Slotted M2 tracks spanning 19mm to 27mm, meant to catch 20x20 or 25.5x25.5 top plate hardware. The Pitch: Locked at 25 degrees of up-tilt. Print in TPU. Do not try this in rigid plastics; you'll never get the camera seated.
Print-in-Place Flexible Crocodile
Toy reptiles are fine until you try to pose them and realise they're cast into a single, rigid block that snaps if you push it. This fixes that. It’s an eight-segment articulated crocodile that prints entirely assembled, right on the bed. The joints are enclosed captive hinges with a 0.45mm clearance, meaning they fuse just enough structure to print safely before breaking free instantly for a massive range of motion. The body tapers from a stylized head down to a narrowed tail, with distinct rib extensions and legs built into the mid-sections. Print Instructions Clearance: 0.45mm gaps in the hinges — make sure your flow rate is dialed in to avoid the joints fusing. Layer Height: 0.2mm recommended. The internal pin tapers rely on standard layer heights to bridge successfully. Adhesion: It prints flat. No brim is required unless you have severe warping issues on small footprints (like the tail tip). Supports: None. The hinge pins use 45-degree chamfers so they print perfectly in mid-air inside their sockets.
Round to Rectangular Duct Adapter
A heavy-duty transition duct adapter for shifting airflow smoothly from a round inlet to a rectangular port. Designed with a continuous linear loft and constant 3mm wall thickness to minimize turbulence. Round inlet: 250 mm inner diameter Rectangular outlet: 300 x 220 mm inner dimensions Total height: 200 mm (including 30 mm attachment collars on each end) Wall thickness: 3 mm
AquaDart — Garden Hose Nozzle
AquaDart introduces a streamlined approach to targeted water pressure. This single-piece nozzle adapts a standard garden hose down to a precise 0.2-inch exit stream. The internal geometry is specifically contoured to accelerate water smoothly, while the exterior features deep grooves for secure hand-tightening even when wet. Dimensions Overall height: 63 mm Base diameter: 38 mm (at the grip) Exit bore: 5.08 mm (0.2 inches) Interface: Standard 3/4" Female Garden Hose Thread (11.5 TPI) Compatibility & Usage Designed to thread directly onto standard North American garden hoses and spigots. Requires a standard rubber hose washer to sit on the internal ledge. Without the rubber washer, standard garden hose threads will leak under pressure. Print Notes Prints completely completely upright and support-free as oriented. Thick walls (4+ perimeters) and 100% infill are heavily recommended to contain the water pressure and prevent layer separation. PETG or ABS is preferred if this will be left outdoors in the sun.
Tandenborstelhouder Voor Gegolfd Potje
Een opzetstuk dat een potje met een golvende rand verandert in een strakke houder voor twee Oral-B tandenborstelkoppen. Een houder op een golvende rand gaat normaal direct wiebelen. Dit model heeft asymmetrische poten die exact zijn uitgesneden met dezelfde wiskundige golf als het potje — hierdoor grijpen de poten als zadels over de rand en zit de houder muurvast, mits geplaatst in de juiste positie (0 of 180 graden). Pot diameter: 50 mm buitenkant (42 mm binnenkant) Golfdiepte: 10 mm verloop Tandenborstel-insteek: 14.5 mm sleuven met een kleine trechtervorm ('flare') zodat je de koppen er blind in kunt schuiven. Print-advies: Geen supports nodig; de bodem overbrugt netjes zolang je part-cooling goed aan staat.
30mm Print-in-Place Hinged Box
A compact, support-free storage case designed to print as a single assembled unit. The clamshell design lies flat on the build plate, using internal conical pins to create a working 180-degree hinge straight off the printer. Dimensions: 30mm square footprint when closed; 20mm total height. Mechanism: Integrated conical barrel hinge with 0.4mm clearances. Closure: Friction-fit horizontal snap ridge on the front lip. Print Setup: Requires no supports. Best printed in PLA or PETG with standard 0.2mm layer heights.
Hexagonal Space Wedding Planter
A simple, flat-faced hexagonal planter designed to tessellate easily for bulk printing. The straight walls ensure flawless surface details without the sagging you get on angled faces. Two of the faces feature vertical embossed text with small stars, and the remaining faces carry subtle celestial elements. Remix Hooks: Two faces are currently left entirely blank, making this a perfect canvas to map your own constellations, drop in an SVG logo, or add extra text. Dimensions: Roughly 90mm across the flats (45mm circumscribed radius) and 60mm tall, with a solid 3mm wall. Printing: Prints flat on the base with zero supports required. The straight sides allow them to pack tightly together on the build plate.
Tessellating Space Wedding Planter
A robust, hexagonal planter intended for bulk printing as a wedding favour. It features completely vertical walls allowing multiple units to pack tightly side-by-side without gaps. Printability: Zero-support geometry optimized for FDM slicing in batches. Engravings: Deeply set names ("Dan & Ash"), a stacked numerical date separated by varied stars, and the Orion constellation. Aesthetic: Clean, minimalist lines offset by randomized 2D star placements around the main text. Clearance: Engraved elements are kept clear of the face edges to ensure crisp lines on all sharp corners.
Rim Bead Saddle Sanding Block
A custom sanding block cut with a compound saddle shape to finish the outer lip of a 20-inch rim. Primary Curve: Matches the 20-inch overall rim diameter. Secondary Groove: Sweeps a 15mm-radius profile along the main curve to cup the bead lip. Grip: Pinch grooves along the sides for better control while sanding.
Index Card Desk Sign
A minimalist desktop stand that holds a standard 4x6-inch index card in landscape orientation. The frame is tilted back at 15 degrees for optimal reading from a seated position, and features an open-top U-shape slot so cards can be dropped in or swapped out instantly. No Supports Required: Prints perfectly flat on its base, with the frame angled to avoid steep overhangs on the inner cavity. Drop-In Fit: Sized at 154mm x 103mm internally to easily accommodate standard and slightly oversized cards. 4mm Retaining Lip: Overlaps the bottom and sides of the card just enough to hold it flat without covering your text.
Sentinel Backup Camera Pod
A rugged, underslung surveillance pod designed to give a powered wheelchair rear-view capabilities. The enclosure mounts flush against T-slot tracking, holding an ESP32-S3 and camera module securely out of the elements. Hardware Integration Board Mounts: Internal standoffs spaced for a standard ESP32-S3 DevKit, sized for M3 heat-set inserts. Rear Panel: Dedicated cutouts for power switch (11.5 x 8.5 mm) and a USB-C feed (12 x 6 mm). Camera: 6mm forward-facing aperture. Lid: 2mm flat plate secured by four M3 screws into corner bosses. Mounting: Twin M3 clearance holes in the base (the "top" when mounted) to bolt directly into T-slot nuts.
Antiquity Signet Ring
A classic signet-style band featuring a flattened bezel to host the engraving. Sized to roughly a US men's 10 (20.2mm inner diameter), it includes inner comfort bevels to soften the top and bottom edges against the finger. The face is deeply engraved with the classical Latin inscription VTERE FELIX (wear in good health). Design Notes Inner diameter: 20.2mm Band width: 9mm Profile: Tapered outer hull transitioning into a 16mm wide flat face Font: Forum (Display) for a traditional Roman cut
M3 Socket Head Diamond Knob
What it's for A compact thumbscrew knob designed to press-fit or glue onto the head of an M3 socket head cap screw. The closed top provides a clean finish while the heavy diamond knurling ensures excellent grip. Dimensions Overall Size: 12mm diameter × 8mm height Recess: 5.5mm diameter, 3mm deep (sized for an M3 socket head) Knurling: 35-degree pitched V-groove diamond hatch Print notes Print flat on its base. No supports are required. If the bolt head is slightly loose, a drop of CA glue in the recess will lock it in permanently.
Support-Free Brain Disco Ball
Having a massive bald spot on the forehead just makes the whole thing look unfinished, but printing the bumps straight into the eye sockets ruins the face entirely. I narrowed the clearance zone down to just the immediate space around the eyes—the upper forehead is covered in brain folds again, but they stop right before crashing into the eyes. Base fits an 11mm dowel Completely solid core Prints without supports
Velocity — Armed Mascot Figure
A stylized geometric interpretation of a fast blue hedgehog mascot, designed as a static desktop figure. Organic modelling isn't native to this format, so the design uses bold, primitive shapes to capture the silhouette—complete with sweeping back-spikes, oversized eyes, and a blocky tactical blaster clamped in the jawline. Details Geometric Spikes: Arrayed in a swept-back pattern to simulate motion. Multipart Colouring: Segments are broken out for the snout, eyes, and hardware to stand out clearly. Integrated Stand: A flat 60mm circular base keeps the figure stable on a desk.
Arcane Tracery Bracer
A 180mm rigid forearm cuff designed around a continuous, self-supporting gothic tracery pattern. The interlocking pointed arches and diagonal cross-cuts mimic the organic load-paths of topology optimization while keeping a distinctly high-fantasy arcane aesthetic. It features a 70-degree slip gap at the back, thick structural armor bands, and rounded comfort edges. Remix hooks Dimensions: Currently scaled for an average arm (35mm inner radius at the wrist, 48mm inner radius near the elbow). To resize it for a different wearer, adjust the wristr and forearmr base variables. Flexibility: The 4mm wall thickness makes this a rigid piece. If you want it to flex open over the wrist rather than sliding on, drop wall_thickness to 2mm and print in PETG. Tracery density: The lattice overlaps heavily to create the branching web. Scaling the width and height of the pointed_cut calls will tighten or open up the negative space. Supportless: The vesica piscis (pointed arch) cutouts are radially oriented and all internal angles exceed 45 degrees, meaning this prints straight up from the wrist with zero supports.
Need a part that doesn't exist yet?
Start building →