3D-printable workshop tools & shop upgrades
Drill guides, tool racks, sanding blocks, dust-collection adapters — functional shop gear with real dimensions, ready to print. Browse what makers built, or describe the exact tool you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Kapsel-Ratschenschlüssel Halterung
Eine maßgefertigte, stark abfallende Halterung für Ratschenschlüssel. Das Design kombiniert technische Präzision mit einer modernen, abgerundeten Formsprache. Kompakt: Unter 165 mm Gesamtlänge, passend für enge Werkzeugschubladen. Geometrie: Fallende Stege (30 mm auf 13 mm) und schrumpfende Lücken (7 mm bis 3 mm) halten die Schlüssel perfekt im Winkel. Details: Eingelassene Beschriftung (22 bis 8), abgerundete Ecken an den Aussparungen und volle Halbkreise an den Enden, durch die die äußeren Schlitze optisch ansprechend auslaufen. Stabilität: Ein massiver 8-mm-Boden sorgt für die nötige Steifigkeit beim Ablegen der massiven Stahlschlüssel.
GripTurn — M12x1.25 Knurled Cap
Ova zaštitna kapa donosi jednostavno, pouzdano zatvaranje za svaki M12x1.25 navoj. Dizajnirana s urezanim rebrima po cijelom vanjskom opsegu, omogućuje čvrst hvat i lagano ručno zatezanje, dok precizan profil čuva navoj od prljavštine i oštećenja. Gornja strana zatvara kapu, a mali otvor služi za provlačenje konca, sajle ili ventilaciju. Specifikacije Navoj: M12 × 1.25 (unutarnji, dubina 20 mm) Vanjske dimenzije: Promjer 20 mm, visina 22 mm Gornji otvor: Promjer 2.8 mm Površina: Rebrasta za lakše okretanje prstima
Clay Cutter with Pressing Rim
A sharp clay cutter that won't dig into your hand when you press down. The cutting edge is shaped to print cleanly with a standard 0.4 mm nozzle, dropping to a precise two-perimeter thickness at the tip. Internal diameter: 100 mm Overall height: 10 mm Tip thickness: 0.8 mm (tapered on the outside only) Pressing rim: 6 mm wide with a rounded upper edge for comfort Prints exactly as oriented, no supports needed.
Bullone M8x30 Testa Quadrata e Dado
Bullone M8x30 con testa quadrata da 23 x 23 mm e spessore 3 mm, abbinato a un dado esagonale M8 con filettatura reale. I due pezzi si stampano separati. Gambo: M8, passo 1,25 mm, filettato per l'intera lunghezza di 30 mm Testa: quadrata 23 x 23 mm, spessore 3 mm Dado: M8, spessore 6,5 mm, 13 mm tra le facce Tolleranze: 6g per il bullone, 6H per il dado Stampa: testa del bullone appoggiata sul piano consigliata, dado con asse verticale
FaceGuard — 2" 300# RF Flange Cap2
FaceGuard is a protective cap for a 2" Class 300 raised-face weld neck flange (Sch 40). It covers the flange face and rim, keeping the sealing surface clean and protected during storage and transport. Features Rim cavity fits over the 6.5" flange OD with light clearance Pocket over the 3.62" raised face Center plug seats in the Sch 40 bore Eight bolt-hole plugs on a 5" bolt circle, sized to fit the 3/4" holes with chamfered tips Print notes Print base-down; no supports needed Dimensions are from standard flange tables. Check against your actual flange before printing.
Bajan Wave — Flag Mold Master
Bajan Wave is a purpose-built 3D-printable master designed for silicone mold-making. It features a sweeping, parametric undulating perimeter that mimics a flag fluttering in the wind, standing out against basic rectangular forms. The basin precisely follows this waving profile and includes the defining elements of the Barbados national flag—vertical section dividers and the iconic broken trident, carefully proportioned to match official specs. The entire underside is perfectly flat, ensuring it sits securely against your casting box base without flashing underneath, while a consistent 8mm perimeter rim includes two integrated resting grooves. Specifications Overall Master Size: 120 mm x 70 mm x 15 mm Basin Floor: 4 mm thick Rim Width: 8 mm constant width following the wave Relief Details: Features a 2 mm raised broken trident and divider bars for high-contrast resin fills.
Empreinte Éventail Rayonnant 50mm
Matrice d'empreinte rigide reproduisant la géométrie d'un éventail ouvert. Conçue pour marquer l'argile, la cire ou d'autres pâtes malléables, la pièce est construite sur un plan de référence plat garantissant une pression uniforme. Le motif est généré par un réseau radial de nervures profilées, sans contre-dépouilles, pour assurer un retrait propre du matériau embouti. Dimensions hors-tout : Hauteur de 50 mm, ouverture de 140 degrés. Épaisseur de base : 3 mm (socle rigide). Motif : 13 nervures coniques s'évasant vers l'extérieur, arrêtées 2 mm avant la bordure pour garantir une marge nette. Démoulage : Les arêtes extérieures sont adoucies et les nervures présentent un profil elliptique aplati (mise en dépouille) évitant l'arrachement de la matière. Tirage : Aucun support requis, fond parfaitement plat adapté au plateau de l'imprimante.
Interlocking Socket Organizer Board
Ein Organizer für Stecknüsse rutscht in der Schublade meist hin und her oder passt im Ganzen nicht auf das Druckerbett. Dieses Board bringt Ordnung in ein sehr umfangreiches Nuss-Sortiment (1/4", 3/8", 1/2" und E-Profil) und teilt sich nahtlos auf, um problemlos gedruckt zu werden. Druck und Montage Drei Teile: Das Board ist über Puzzle-Verbinder mit 0.25 mm Toleranz in drei Stücke à maximal 187 mm geteilt. Farbwechsel: Platte und Zapfen bleiben in der Datei als separate Teile deklariert, ideal für einen Farbwechsel beim Drucken (z. B. auf Z=3 mm). Kein Kleben: Die Teile rasten sauber ineinander ein. Sitzt ein Zapfen genau auf der Schnittkante, wird er mitgetrennt und die Nuss überbrückt später beim Aufstecken den Spalt.
VakuumRačva — Ojačani Model
VakuumRačva je robustan, ojačan T-profilni razvodnik namenjen za pouzdano povezivanje vakuumskih vodova. Ovaj model poseduje namenski M10 navoj na zadnjem delu koji je sada dodatno stabilizovan konusom protiv pucanja slojeva pri bočnom opterećenju. Specifikacije Glavni navoj: Unutrašnji 1/4" BSP (dubine 15 mm) za prihvat vakumetra. Dodatni navoji: Spoljni M12 (korak 1.25) na debljem kraku i spoljni M10 (korak 1.5) na zadnjem delu. Protok: Unutrašnji kanali obezbeđuju ravnomeran prenos bez suženja (6 mm i 6.2 mm). Ojačanja: Konusne baze ispod svih kritičnih priključaka čuvaju integritet komada. Preporuke za štampu Štampajte od PETG ili ABS materijala zbog mehaničke otpornosti. Manja visina sloja osiguraće da navoji lakše prihvate spojeve.
П-Shape Bracket Profile
A custom rectangular П-shaped bracket or profile section. Overall dimensions: 29mm wide, 37mm deep, 111mm high Wall thickness: 3mm continuous on top and sides Open base and through-cut depth
Emergency Stop collar
A high-visibility collar for an emergency stop button. The lettering is set in heavy sans-serif and extruded for clear tactile and visual feedback, making it ideal for multi-color filament swaps. Dimensions Outer Diameter: 64 mm Bore: 25 mm Base Thickness: 2 mm Total Height: 3.5 mm (including text) Print Notes Color Swap: Pause at 2.0 mm (or Z=2.2 mm depending on layer height) to swap to an accent color for the text. Line Width: A 0.4 mm nozzle will handle the bold Archivo Black lettering nicely.
Ojačana Vakuum Račva Sa Navojima
Ojačana račva u obliku slova T za spajanje cevi i vakumetra. Glavno telo: Prečnik 21 mm, dužina 44 mm, zatvoreno sa jedne strane. Na otvorenom kraju nalazi se integrisani ženski 1/4" BSP navoj za vakumetar, sa plitko oborenom ivicom. Krak sa navojem: Ukupna dužina 27 mm (12 mm glatki deo, 15 mm navoj na vrhu). Spoljni navoj je M12 sa korakom 1.25. Kroz njega prolazi kanal od 6.2 mm. Glatki krak: Dužina 26 mm, spoljni prečnik 10 mm. Kanal za protok je 6 mm. Ojačanja na spoju oba kraka sa glavnim telom smanjuju stres pod uglom od 90 stepeni i sprečavaju lomljenje slojeva tokom upotrebe.
Screw-On Large-Hole Spool Holder
A plate-mounted spool holder for filament spools with large central holes. A hollow 48 mm spindle rises from a flat mounting plate and ends in a flared lip that keeps the spool from sliding off. Remix hooks Spindle diameter (48 mm): change to suit your spool bore; most big-hole spools measure 50–58 mm, so leave 2–4 mm of play. Spindle length (70 mm): stretch for wide spools, shorten for slim ones. Plate (110 × 64 × 6 mm): screw holes sit 44 mm either side of centre, 4.5 mm with countersinks. Move them to match your panel, or add a third hole. Lip: 58 mm with a 45° underside so it prints without supports. Make it a removable cap for easy spool swaps. Wall (3 mm): thicken for heavy 3 kg spools, or add ribs. Prints plate-down with the spindle pointing up. Mount with the plate against a vertical panel so the spindle points sideways; a pair stacks well for dual spools.
100mm Concentric Breakaway Disc
100mm concentric stepped disc connected entirely by breakaway tabs. Used to verify dimensional accuracy, extrusion multipliers, and single-wall adhesion on FDM toolheads. Critical Fitment Outer Diameter: 100 mm exactly. Bridges: 0.6 mm wide (designed to lay down as 1 to 2 perimeters on a standard 0.4 mm nozzle). Clearance Gap: 1 mm radial gap between rings. Notes If the flow rate is dialed in, the rings will break away clean under manual pressure. If the printer over-extrudes, the bridges will fuse solid and refuse to yield. Standard 3 mm thickness flat stock — do not run on a raft.
Set van 5 Tandwielen
Een set van vijf tandwielen met een vaste tandgrootte (moduul 2), waardoor ze met elkaar kunnen ingrijpen. Ze zijn naast elkaar geplaatst met een kleine tussenruimte zodat ze direct als losse onderdelen geprint kunnen worden. Specificaties Tandwielen: 5, 10, 15, 20 en 25 tanden Tandgrootte: Moduul 2 Dikte: 5 mm Asgat: 2 mm diameter Tussenruimte: 2 mm (klaar om te printen)
Steckschlüssel-Halterung für 1/2-Zoll
Drei schlanke Steckschienen, passgenau für 1/2-Zoll-Stecknüsse. Jede Schiene misst 246 mm in der Länge, mit erhabenen Größenangaben für schnelles Finden der richtigen Nuss. Die Konstruktion: Format: Schmale 28 mm Breite und 3 mm starke Grundplatten sparen Platz in der Schublade. Aufnahmen: 12,5 mm Seitenlänge mit leichter Einführschräge für optimales Aufstecken ohne Klemmen. Ordnung: Vorgesehen für Größen von 11 bis 32, aufgeteilt in logische Gruppen.
Split-Span Laser Gantry
A modular laser mounting gantry spanning an exact 330mm width. Built for smaller print beds, the two-piece frame locks together in the centre with a clearance-tuned puzzle joint that draws the span tight when seated. Adjustments & Tolerances The Joint: 0.5mm clearance around the jigsaw neck. Best printed flat to put layer strength along the span. The Slider: Sits exactly over the seam and locks down with an M4 tap bolt through the top. Laser Mount: Single 6.5mm hole on the face block, ready for standard laser unit clamps. Table Mount: Four 5.5mm mounting holes positioned straight down through the feet for screwing straight into your baseboard.
Anello Frazionato da Palo
Un anello di spessoramento diviso a metà, progettato per essere montato attorno a un palo da 137 mm di diametro. Profilo: Parete spessa 3 cm Fori: Quattro fori passanti verticali, diametro 4 mm, disposti in quadrato con lato 121 mm Assemblaggio: Spaccato centralmente per consentire l'installazione su tubi e pali esistenti senza doverli sfilare. Utile per creare spessori o basi su tubolari in metallo o PVC.
Screwdriver Handle With Bit Storage
Digging through a loose pile for the exact bit wastes time, so this 1/4-inch hex screwdriver handle keeps six spare bits loaded directly in the base. The main driving socket holds the active bit with a recessed magnet, while the spare slots are kept out of the way so the sharp ends stay clear of your grip while turning. Fit and Hardware Overall Size: 100 mm long by 30 mm diameter. Main Socket: 1/4-inch (6.35 mm) hex, sized to 6.6 mm for printed clearance, with a pocket at the bottom for a standard 6x3 mm neodymium magnet. Spare Magazine: Six hex slots cut 18 mm deep, leaving roughly 7 mm of a standard 1-inch bit exposed so they can be pulled out by hand. Grip: Six flutes offset from the bit holes to maintain wall thickness and provide torque.
Wide Stance Filament Spool Stand
Filament spools that hang off the edge of undersized holders are a constant source of drag and jams. This A-frame stand widens the track, catching oversized spools before they can derail. Fit and Bed Limits Inner Clearance: 160 mm between the uprights Base Width: 180 mm Spindle Height: 192 mm Printability: The entire layout is spaced to fit on a 220x220 mm bed without needing rotation or supports.
160mm Square Base Plate
What it's for A simple, flat 160mm square plate, suitable as a foundational base, shim, or blank canvas for further structural modifications. Dimensions Width & Length: 160 mm x 160 mm Thickness: 4 mm Remix ideas Subtract precise mounting holes to use it as an electronics sled. Carve out a hex grid to create a lightweight mesh panel. Emboss or deboss a logo into the top face.
20 mm Round Disc, 2 mm Thick
A flat 20 mm round disc, for when a 2D circle needs to become something you can print and hold. A bare circle has no thickness, so this gives it enough to print as a solid piece. Print details Diameter: 20 mm Thickness: 2 mm (assumed, since a plain circle has no height) Sits flat on the bed, no supports needed Prints in any filament
Embroidery Hoop Clearance Frame
A single-piece clearance frame for testing fabric fitment against the dimensions of the Brother SA431 / EF61 small embroidery hoop. Designed for FDM printing as a rigid, continuous ring, it skips mounting hardware in favour of a plain profile for preliminary dimensional checks. Inner clearance: 50 mm × 38 mm Overall footprint: 60 mm × 48 mm Frame width: 5 mm uniform wall Thickness: 4 mm Z-height
montre
What it's for A 3D-printable watch case modelled on dive-watch proportions. Features a scalloped rotating-style bezel with minute markers, a fine threaded base for the case back, and integrated lugs for a standard watch strap. The inner cavity tapers to secure a movement, with a lip cut for a domed crystal. Dimensions Overall Case: 42 mm diameter Inner Cavity: 41 mm base, tapering to 40.4 mm at the dial Lugs: Spaced for a 20 mm strap Crystal Seat: 41.4 mm diameter, 1 mm deep Stem Hole: 1.1 mm diameter at the 3 o'clock position Threads: 0.5 mm pitch, matching case back included Print notes The case back uses a very fine 0.5 mm thread pitch. This requires a well-calibrated printer and low layer heights (0.12 mm or finer) to print cleanly. You may need to scale the case back slightly on the X and Y axes depending on your printer's tolerances.
Need a part that doesn't exist yet?
Start building →