3D-printable workshop tools & shop upgrades
Drill guides, tool racks, sanding blocks, dust-collection adapters — functional shop gear with real dimensions, ready to print. Browse what makers built, or describe the exact tool you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Hoof Evener Thumb Ring 1.2
A low-profile thumb ring designed to index a farrier's hoof-evener ruler. 1/8" Slim Ring: Keeps bulk out of the way while holding the thumb perfectly on zero. D-Profile Peg: The 6mm mounting peg is shaved flat on the back, allowing the entire model to print dead-flat on the bed without any supports. Flex Slit: Open front ensures it can comfortably accommodate varying thumb sizes.
Farrier Hoof Evener Ruler V 1.12
A print-ready pair of hoof evener rulers, 6-inch and 8-inch, with four marker assemblies laid out on the same plate. Each ruler has an open viewing window, a solid center bridge, raised tick marks on the inside of each rail and numbers on the outside. A 3.5 mm hole at dead center takes a slim flexible ring. Scales end exactly at 6 and 8 inches, with extra length at each end for the sliders to reach 0 and the end mark Two sliders per ruler, so each end can hold a marker Each slider has a thin blade foot, a round peg with an M2 pilot hole and an arrow cap with a small notch to see the hoof edge Domed pins on the foot click into hidden dimples under the ruler at each quarter inch Printed flat, no supports needed for the rulers
Hex Tube 40 mm Tall With Center Bore
A hex tube, 4 cm tall, for when a round spacer or standoff spins or rolls where a flat-sided one would hold still. The 2.5 mm bore runs the full length so a rod, wire or screw passes straight through. Key dimensions Height: 40 mm Width: 5.15 mm point to point Center bore: 2.5 mm diameter, through the full length Printing Print standing upright, no supports needed. Walls are thin at the hex flats, so use at least 2 perimeters and a small nozzle if possible.
69 mm Round Spacer, 5 Holes
A round spacer 69 mm in diameter and 10 mm tall with a 40 mm center bore and five 5.5 mm through-holes on a 54 mm bolt circle. Outer diameter: 69 mm Height: 10 mm Center hole: 40 mm Bolt holes: 5 × 5.5 mm on a 54 mm circle Hole spacing: 68°, 72°, 72°, 68°, 80° (the 80° gap is between the last and first hole) Prints flat with no supports
J-Shaped Pocket Edge Fabric Clip
A 40 mm wide J-clip that grips a fabric pocket edge. A flat back plate holds two countersunk M3 screw holes, and a sprung leg closes back toward it. Remix hooks Relaxed gap: 1.5 mm, set by the leg angle (about 6°). Raise it for thick cloth, lower it for more grip. Tooth: 0.8 mm round bump 12 mm from the leg tip. Make it larger, or remove it for a smooth clamp. Mouth flare: 25° over the last 6 mm. A wider flare helps with thick fabric. Bend radius: 3 mm inner, with 2.6 mm walls. Print with layers running along the width so the bend doesn't split. Holes: 25 mm apart, 20 mm up from the bottom, 3.4 mm with a 6 mm countersink. Change the spacing to match a mounting pattern. Plate is 45 mm tall and the leg is 42 mm long. It pairs well with PETG or nylon for spring.
Fabrication-Ready Welded Railing explode
A heavy-duty 2-meter railing section designed for real metal fabrication. The components are drafted with realistic 2mm root gaps at every joint and heavy 4mm chamfers simulating weld bevels, so the model accurately reflects standard weld-prep fitment. Overall Size: 2000mm long by 1500mm tall. Post Size: 60mm square stock. Rails: 50x40mm profile, with a 120mm bottom clearance. Balusters: 20mm square, 150mm on-center spacing. Joinery: Ends are shortened by 2mm and heavily chamfered to provide a realistic V-groove root gap for welding.
Industrial Pull Plate
A heavy-duty mounting plate featuring an integrated pull tab and precise counterbored holes. Designed for easy handling and a flush fit with socket head hardware. Mounting Interface: 4x 4.3mm thru-holes with 6.5mm counterbores (4mm deep) Spacing: 72mm x 40mm pattern Convenience: Rounded 35mm pull tab with a 10mm grip hole
door lock
Rectangular block, 100 mm long, 24 mm wide and 15 mm tall, with a 16 mm wide by 11 mm deep groove running the full length along the top centre. The groove size is engraved into the groove floor as "16 x 11 mm". Overall size: 100 x 24 x 15 mm Groove: 16 mm wide x 11 mm deep, open at both ends Side walls: 4 mm; floor: 4 mm Engraving: 0.6 mm deep, readable from above Prints flat with no supports
608 Bearing Level Wind Shaft
A continuous reversing lead screw shaft, designed to drive a reciprocating carriage without needing the motor to switch direction. Ends are dimensioned for a 608 bearing (8 mm bore). The track is a 5 mm spherical U-groove; pair it with a 4.5 mm or 4.8 mm round follower pin so it can swivel without binding at the turnarounds. Total effective travel between reversing points is 75 mm.
Metabo Schlauchadapter 35mm zu 39mm
Wofür es ist Ein massiver Werkstatt-Schlauchadapter, der speziell für Metabo Industriesauger ausgelegt ist. Er verbindet Schläuche oder Anschlüsse mit 35 mm und 39 mm Außendurchmesser. Dimensionen Gesamtlänge: 85 mm Steckbereich schmal: 45 mm Länge, 35 mm Durchmesser (gerade) Steckbereich breit: 30 mm Länge, 39 mm Durchmesser Wandstärke: 2,5 mm Druckhinweise Ausreichend Perimeter (mindestens 3-4) drucken, damit die Wandung stabil und luftdicht bleibt. PETG oder ABS sind für den harten Werkstatteinsatz zu empfehlen, PLA geht bei leichterer Beanspruchung auch in Ordnung.
Brændpunktsskinne til ellipsetegning
En flad skinne med 11 nummererede huller og to pinde, der bruges til at tegne ellipser med en snorløkke. Skinnen er 170 × 18 × 4 mm med afrundede hjørner (radius 6 mm), og hullerne sidder med 15 mm afstand. Remix-muligheder Antal huller: n = 11 giver 170 mm i længden. Brug et ulige tal for at beholde 0 i midten. Hulafstand: 15 mm. Mindre afstand giver finere trin i excentriciteten. Hjørneradius: 6 mm. Kan sættes op til ca. 8 mm uden at ændre bredden. Pinde: Skaft 8 mm, krave 11 mm, hals 5 mm til snoren. Gør skaftet 0,2 mm tykkere, hvis pindene skal sidde fast. Passer til: En snorløkke på ca. 200 mm indvendigt og et A4-papir.
outside hat
A plain flat disc in the spirit of an oversized washer or a vinyl-record blank: 3 inches across, 1/8 inch thick, with a clean 1 cm hole through the centre. Prints flat with no supports. Diameter: 76.2 mm (3 in) Thickness: 3.175 mm (1/8 in) Centre hole: 10 mm Good for spacers, coasters, templates, or as a base for other builds
12-Inch L-Profile Bracket
A straightforward 90-degree L-profile extrusion, built to a 1.5" × 3" footprint and spanning 12 inches in length. Perfect as stock geometry for building custom brackets, rails, or edge guards. Remix Hooks Thickness: Currently set to a sturdy 1/4" (6.35 mm). This is the most obvious candidate for tweaking if you need a lower profile or a heavy-duty structural piece. Mounting: It's a blank slate. Drop in some counterbored holes along the Y-axis leg if you're mounting it to a wall, or slot it for adjustable brackets. Edge Treatment: The corners are left sharp for flush mounting, but adding a fillet to the inner vertex would strengthen the joint significantly for load-bearing use.
Canal Skimmer Prototype
This is a 1:1 scale educational prototype of a floating litter skimmer, designed to illustrate canal and river clean-up strategies for a science fair or engineering project. The model integrates common upcycled materials into its conceptual design, showing how basic geometry can tackle surface flow. The assembly features: Buoyancy Pontoons: Four simulated plastic bottles that keep the frame level and balanced on the water. Catchment Ramp: An angled, perforated mesh ramp that dips below the surface line to channel floating debris upward. Filtration Basket: A removable, slotted rear basket for detaining waste while allowing water to pass through. Sample Load: Included simulated litter (bottles and leaves) to demonstrate the collection path in action.
Canal Skimmer Prototype
This is a 1:1 scale educational prototype of a floating litter skimmer, designed to illustrate canal and river clean-up strategies for a science fair or engineering project. The model integrates common upcycled materials into its conceptual design, showing how basic geometry can tackle surface flow. The assembly features: Buoyancy Pontoons: Four simulated plastic bottles that keep the frame level and balanced on the water. Catchment Ramp: An angled, perforated mesh ramp that dips below the surface line to channel floating debris upward. Filtration Basket: A removable, slotted rear basket for detaining waste while allowing water to pass through. Sample Load: Included simulated litter (bottles and leaves) to demonstrate the collection path in action.
Baluster Drill Jig
A precise drill guide for 1.375-inch square balusters. Centers a 3/8-inch bore perfectly in the end grain. Features an open-corner skirt that drops down two inches to grip the baluster on all four sides, ensuring plumb alignment while letting you easily verify the jig is seated fully against the wood. The center windows in the tabs save print time and reduce material waste. Printing Fitment The internal bore is modeled with clearance for a 3/8-inch bit so it spins freely without melting the plastic, and the skirt has 0.5mm total clearance to slip cleanly over milled lumber. Measure your balusters before printing — milled dimensions can vary depending on moisture and the lumber yard.
Triple Spool Wire Dispenser
A desktop dispenser for keeping hookup wire and solder from turning into a bird's nest. It runs three separate spools on a shared drop-in rod, with individual funnel-shaped feed holes so the lines pull smoothly without catching. Printed spacer washers sit between the spools to keep them turning independently. Remix Hooks & Starting Dimensions The Rod: The printed shaft sits at 7.6mm to clear the 8.5mm U-slots, but the obvious durability upgrade is swapping it out for a standard 8mm aluminum tube or wooden dowel. Spool Capacity: The internal bay is 115mm wide and easily clears spools up to 60mm in diameter. If you are using wider spools, the main block width is the parameter to stretch. Feed Clearances: The front guides are built from 4mm cylinders that widen to 10mm funnels on the inner wall. Bump the 4mm base diameter up if you are pulling heavy-gauge wire or thick heat shrink.
Closed Helical Micro Spring
A miniature closed-end helical spring. Designed to rest squarely on flat surfaces, the outer coils taper into a zero-pitch ring to distribute force evenly across the ends. Overall height: 7 mm Outer diameter: 3.5 mm Wire thickness: 0.45 mm FDM Printing Note: Printing at this scale usually produces parts much stiffer than their injection-molded counterparts. Expect rigid behavior unless printed in highly compliant TPU.
Klipper Telemetry Console
A compact enclosure for Klipper printer telemetry, mounting to standard 2040 extrusion. This version features revised back cover mounts that embed securely into the enclosure walls, ensuring robust assembly. Revised Mounts: Structural corner blocks anchor the back plate safely to the frame. Component Fits: Room for a 1602A LCD and 32x32mm MAX7219 matrix. Mounting: Flush side flange with M4 t-nut clearance.
Klipper Display and Status Console
Compact left-side mounting enclosure for Klipper printer telemetry, designed specifically for the Ender 3 Pro 2040 vertical extrusion. Hardware Compatibility: Fits a 1602A I2C LCD, a 32x32mm HW-109 MAX7219 LED Matrix, and a standard 5mm RGB LED. Internal Clearance: 36mm cavity depth cleanly clears standard I2C backpacks. Mounting System: Left-oriented 5mm side flange using dual slots for M4 t-nuts. Flange sits flush to the bottom, leaving top clearance for gantry travel. Assembly: Snap-fit 2mm front panel with internal screw bosses; back plate secured via four M3 interior corners. The housing prioritises rigidity and short wiring paths over bulk, anchoring firmly without compromising structural frame limits.
Precision Rectangular Spacer Frame
Ein präziser, flacher Rechteckrahmen mit zentriertem Ausschnitt. Das Profil eignet sich gut als Abstandshalter, Passepartout oder Montage-Shim. Außenmaße: 39 × 30 mm Dicke: 3 mm Ausschnitt: 29 × 25 mm (mittig) Wandstärken: 2,5 mm seitlich, 5 mm an den Enden
Precision Imperial Gauge Blocks
A set of five exact imperial gauge blocks with flush text inlays. 1 inch, 2 inch, 3 inch, 6 inch, and 8 inch blocks Exact 1-inch width and 0.5-inch thickness Flush text inlays for multi-color printing without breaking the outer dimensional envelope
Uchwyt latarki Dragon HT05
Wsuwany boczny uchwyt do hełmu strażackiego Dragon HT05, przystosowany do latarek typu Iskra LED. Zaprojektowany jako jeden zwarty element. Zaczepy do modyfikacji Obejma latarki: Otwór ma 30 mm, a szerokość wcięcia wynosi 72% tej wartości (dobry zatrzask dla materiałów takich jak PETG). Szyna montażowa: Standardowo profil 25 mm na 4.5 mm, z drobną sferyczną wypustką do wyczuwalnego zablokowania w slocie hełmu. Orientacja: Model w całości zorientowany jest tak, by leżeć płasko na stole – nie używaj tu podpór, wydrukuje się gładko w jednym przejściu osi Z.
5-Way Flat H-Manifold
What it's for A flat pneumatic or fluid splitter featuring five branches. Arranged in an H-configuration with an additional trailing branch, keeping the entire assembly planar for simple routing and straightforward printing. Dimensions Branch outer diameter: 10 mm Branch inner diameter: 7 mm (1.5 mm walls) Overall length: 50 mm (from the closed cap to the tail tip) Overall width: 40 mm (across the parallel arms) Spacing: 25 mm between the two cross sections Print notes Lays entirely flat on the print bed. The horizontal pipes print safely without supports on most standard FDM setups.
Need a part that doesn't exist yet?
Start building →